Study guide

11.6 After Journeyman: Master, Contractor, and Continuing Education

Journeyman Electrician Study Guide Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Exam Orientation and Source Control

1.1 ICC R17, T17, G17, and Jurisdiction Variance 1.2 Current Format, Cost, Time, and Passing Score 1.3 Licensing Board vs. Exam Provider 1.4 Official References, Open-Book Rules, and Calculators 1.5 Domain Weights and Study Map 1.6 Using the Practice Bank, Error Log, and NEC Index

2 Chapter 2: NEC Navigation, Definitions, and Code Strategy

2.1 NEC Book Structure and Article Map 2.2 Article 100 Definitions and Exam Language 2.3 Index, Table, and Annex Navigation 2.4 Shall, Shall Not, Permitted, and Informational Notes 2.5 Using Code References Without Overlooking Context 2.6 State Amendments and Code Edition Control 2.7 NEC Navigation Case Lab

3 Chapter 3: Electrical Theory and Calculation Foundations

3.1 Ohm's Law, Power, and Basic Units 3.2 Series, Parallel, and Circuit Behavior 3.3 Single-Phase, Three-Phase, and Voltage Systems 3.4 Continuous Loads, Demand, and 125 Percent Rules 3.5 Voltage Drop and Practical Calculation Setup 3.6 Load Calculation Workflow 3.7 Calculation Foundation Case Lab

4 Chapter 4: Services, Service Equipment, and Grounding/Bonding

4.1 Service Point, Service Conductors, and Disconnects 4.2 Service Load Calculation and Sizing 4.3 Service Equipment, Panelboards, and Switchboards 4.4 Grounding Electrode System and GEC 4.5 Bonding, Main Bonding Jumpers, and Effective Fault Path 4.6 Transformers and Separately Derived Systems 4.7 Services and Grounding Case Lab

5 Chapter 5: Feeders, Branch Circuits, and Conductor Sizing

5.1 Feeder vs. Branch Circuit Boundaries 5.2 Branch Circuit Ratings and Required Outlets 5.3 Conductor Ampacity, Temperature, and Terminal Ratings 5.4 Adjustment, Correction, and More Than Three Conductors 5.5 Overcurrent Protection and Small-Conductor Rules 5.6 GFCI, AFCI, Equipment Grounding, and Dwelling Circuits 5.7 Feeders and Branch Circuits Case Lab

6 Chapter 6: Wiring Methods, Raceways, Boxes, and Cables

6.1 Raceway Selection and Installation Logic 6.2 Underground Wiring, Wet Locations, and Protection 6.3 Boxes, Enclosures, and Conduit Bodies 6.4 Box Fill, Conductor Counting, and Device Yokes 6.5 Cabinets, Panelboards, and Switchboards 6.6 Flexible Cords, Cables, and Temporary Wiring 6.7 Wiring Methods Case Lab

7 Chapter 7: Equipment, Devices, Luminaires, and Controls

7.1 Receptacles, Switches, and Device Selection 7.2 Luminaires, Lampholders, and Lighting Outlets 7.3 Appliances and Utilization Equipment 7.4 Heating, Cooling, and HVAC Electrical Connections 7.5 Disconnects, Controllers, and Switching Devices 7.6 Equipment Grounding, Bonding, and Listing Markings 7.7 Equipment and Devices Case Lab

8 Chapter 8: Motors, Generators, Transformers, and Special Equipment

8.1 Motor Circuit Anatomy and Article 430 Navigation 8.2 Motor Conductors, Overload, and Short-Circuit Protection 8.3 Motor Controllers, Disconnects, and Nameplates 8.4 Generators, Transfer Equipment, and Optional Standby 8.5 Transformer Sizing, Protection, and Grounding 8.6 Emergency Systems, Fire Alarms, and Signaling Overview 8.7 Motors and Generators Case Lab

9 Chapter 9: Special Occupancies, Renewables, and Safety

9.1 Hazardous Classified Locations 9.2 Healthcare, Marinas, RV Parks, and Mobile Home Parks 9.3 Pools, Spas, and Similar Installations 9.4 Solar PV, Energy Storage, and Renewable Systems 9.5 Temporary Power, Emergency Systems, and Special Conditions 9.6 OSHA Subpart K and Safe Work Practice Context 9.7 Special Occupancies Case Lab

10 Chapter 10: Open-Book Exam Workflow and Mixed Code Labs

10.1 Four-Hour Pacing and Question Triage 10.2 Look-Up vs. Know-From-Memory Decisions 10.3 Mixed Calculation Lab 10.4 Mixed Code Navigation Lab 10.5 Diagnostic Report and Error Log Remediation 10.6 High-Weight Domain Remediation Plan 10.7 Full Exam Simulation Playbook

11 Chapter 11: Final Review, Test Day, and License Planning

11.1 Final Two-Week Study Plan 11.2 Reference Book, Tabs, and Allowed Materials Checklist 11.3 Pearson VUE, PRONTO, and Test-Day Rules 11.4 After the Exam: Results, Retakes, and Challenges 11.5 License Application, Work Hours, and Jurisdiction Next Steps 11.6 After Journeyman: Master, Contractor, and Continuing Education

11.6 After Journeyman: Master, Contractor, and Continuing Education

Key Takeaways Explain This Topic AI

Journeyman, master, and contractor are different roles or license classes in many jurisdictions, and candidates must verify the scope and requirements locally.

ICC lists related master electrician exams G16-N, T16-N, and R16-N, and the source brief notes that the Master Electrician contractor/trades exam requires 75%.

A journeyman license often leads to renewal, continuing education, code-update, supervision, or local-registration responsibilities that are set by the jurisdiction.

Career planning should include code-cycle awareness, documented experience, safety habits, and clear separation between individual licensing and business authority.

Last updated: May 2026

The journeyman result is a platform

Passing a journeyman electrician exam can be a major step, but it is not the end of the licensing path. Many electricians later consider a master electrician license, a contractor license, specialty licenses, supervisory roles, inspection work, estimating, project management, maintenance leadership, or teaching apprentices. Each path has different rules and different authorities.

The current ICC national exam list in the source brief identifies related master electrician exams: G16-N, T16-N, and R16-N. It also identifies residential electrician exams: G18-N, T18-N, and R18-N. Those codes matter because they show that journeyman, master, and residential exams are distinct tracks. Do not assume that passing a journeyman exam automatically satisfies master or contractor requirements.

Master electrician planning

A master electrician license, where used, usually signals a higher level of responsibility. It may involve design judgment, supervision, permit responsibility, business qualification, or broader scope depending on the jurisdiction. The source brief states that the Master Electrician contractor/trades exam requires 75%, while contractor/trades exams generally require 70% and ICC national certification exams use a different scaled-score concept. Do not apply the master 75% number to journeyman, and do not assume journeyman rules apply to master.

If master licensing is a goal, start a documentation habit immediately after journeyman licensure. Keep employer records, project types, supervision history, continuing education certificates, code-update courses, and license renewal confirmations. Boards that require additional experience may ask for records later, and reconstructing years of employment is harder than saving documents as you go.

Contractor authority is different

An individual journeyman or master license is not always the same as authority to operate an electrical contracting business. Contractor licensing may involve business registration, responsible master or qualifying individual rules, bonds, insurance, workers compensation, tax registration, local permits, and separate exams. Some jurisdictions separate trade competence from business and law competence.

Before advertising services, signing contracts, pulling permits, or hiring employees, ask the jurisdiction exactly what authority is required. The wrong assumption can create legal, insurance, and permit problems. Passing a technical NEC-centered exam does not automatically create business authority.

Continuing education and renewal

Licenses often have renewal cycles. Many jurisdictions require continuing education, code update classes, safety training, or proof of active status. The specific hours, topics, providers, and deadlines vary. Verify them with the licensing authority and calendar them when the license is issued.

Continuing education is not just a paperwork burden. The ICC exam list already shows multiple NEC editions in active use: G17-N uses 2017 NEC, T17-N uses 2020 NEC, and R17-N uses 2023 NEC. Field work may occur under a local adoption cycle that differs from a national exam cycle. A working electrician needs to know which edition governs the job, the permit, the inspection, and any future exam.

Keep a code-cycle file

A practical code-cycle file includes:

Current license and renewal date.

Jurisdiction adoption date for the NEC edition used in your work.

Local amendments and utility service requirements.

Continuing education certificates.

OSHA and jobsite safety training records.

Employer letters or project summaries if future licensure may require them.

Notes on major NEC changes between editions you use.

OSHA 1926 Subpart K is useful safety context for construction electrical work. It addresses electrical safety subjects such as wiring design and protection, wiring methods, equipment, special systems, hazardous locations, lockout and tagging, and related requirements. Use OSHA as safety context and jobsite compliance information, not as a substitute for the NEC or the ICC exam outline.

Career outlook and responsibility

The BLS source in the brief describes electricians as workers who install, maintain, and repair electrical power, communications, lighting, and control systems. It also reports that most states require electricians to be licensed, that typical training is apprenticeship, and that employment demand is expected to grow faster than average in the 2024 to 2034 period. Those facts support long-term planning, but they do not change your local license rules.

A good post-journeyman plan is specific:

Goal Source to verify Records to keep

Renew journeyman license Licensing board CE certificates, fee receipts, renewal confirmation.

Upgrade to master Licensing board and exam catalog Experience records, supervision proof, code courses.

Become contractor Contractor board or local authority Business registration, bond, insurance, qualifying person records.

Work across jurisdictions Receiving jurisdiction Reciprocity, endorsement, local registration, local amendments.

Specialize Board or specialty authority Manufacturer training, specialty license, safety credentials.

Keep studying like a working electrician

The best exam habit carries into practice: identify the authority, find the rule, check definitions, check exceptions, and document the decision. That habit helps with inspections, change orders, troubleshooting, and supervising helpers. It also prevents overconfidence after passing.

Treat the journeyman credential as permission to keep building competence under the rules of your jurisdiction. The next steps are not universal, but the method is stable: verify the authority, preserve documentation, keep current with code cycles, and do not expand your legal scope until the proper license or registration is in place.