Study guide

8.5 Transformer Sizing, Protection, and Grounding

Journeyman Electrician Study Guide Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Exam Orientation and Source Control

1.1 ICC R17, T17, G17, and Jurisdiction Variance 1.2 Current Format, Cost, Time, and Passing Score 1.3 Licensing Board vs. Exam Provider 1.4 Official References, Open-Book Rules, and Calculators 1.5 Domain Weights and Study Map 1.6 Using the Practice Bank, Error Log, and NEC Index

2 Chapter 2: NEC Navigation, Definitions, and Code Strategy

2.1 NEC Book Structure and Article Map 2.2 Article 100 Definitions and Exam Language 2.3 Index, Table, and Annex Navigation 2.4 Shall, Shall Not, Permitted, and Informational Notes 2.5 Using Code References Without Overlooking Context 2.6 State Amendments and Code Edition Control 2.7 NEC Navigation Case Lab

3 Chapter 3: Electrical Theory and Calculation Foundations

3.1 Ohm's Law, Power, and Basic Units 3.2 Series, Parallel, and Circuit Behavior 3.3 Single-Phase, Three-Phase, and Voltage Systems 3.4 Continuous Loads, Demand, and 125 Percent Rules 3.5 Voltage Drop and Practical Calculation Setup 3.6 Load Calculation Workflow 3.7 Calculation Foundation Case Lab

4 Chapter 4: Services, Service Equipment, and Grounding/Bonding

4.1 Service Point, Service Conductors, and Disconnects 4.2 Service Load Calculation and Sizing 4.3 Service Equipment, Panelboards, and Switchboards 4.4 Grounding Electrode System and GEC 4.5 Bonding, Main Bonding Jumpers, and Effective Fault Path 4.6 Transformers and Separately Derived Systems 4.7 Services and Grounding Case Lab

5 Chapter 5: Feeders, Branch Circuits, and Conductor Sizing

5.1 Feeder vs. Branch Circuit Boundaries 5.2 Branch Circuit Ratings and Required Outlets 5.3 Conductor Ampacity, Temperature, and Terminal Ratings 5.4 Adjustment, Correction, and More Than Three Conductors 5.5 Overcurrent Protection and Small-Conductor Rules 5.6 GFCI, AFCI, Equipment Grounding, and Dwelling Circuits 5.7 Feeders and Branch Circuits Case Lab

6 Chapter 6: Wiring Methods, Raceways, Boxes, and Cables

6.1 Raceway Selection and Installation Logic 6.2 Underground Wiring, Wet Locations, and Protection 6.3 Boxes, Enclosures, and Conduit Bodies 6.4 Box Fill, Conductor Counting, and Device Yokes 6.5 Cabinets, Panelboards, and Switchboards 6.6 Flexible Cords, Cables, and Temporary Wiring 6.7 Wiring Methods Case Lab

7 Chapter 7: Equipment, Devices, Luminaires, and Controls

7.1 Receptacles, Switches, and Device Selection 7.2 Luminaires, Lampholders, and Lighting Outlets 7.3 Appliances and Utilization Equipment 7.4 Heating, Cooling, and HVAC Electrical Connections 7.5 Disconnects, Controllers, and Switching Devices 7.6 Equipment Grounding, Bonding, and Listing Markings 7.7 Equipment and Devices Case Lab

8 Chapter 8: Motors, Generators, Transformers, and Special Equipment

8.1 Motor Circuit Anatomy and Article 430 Navigation 8.2 Motor Conductors, Overload, and Short-Circuit Protection 8.3 Motor Controllers, Disconnects, and Nameplates 8.4 Generators, Transfer Equipment, and Optional Standby 8.5 Transformer Sizing, Protection, and Grounding 8.6 Emergency Systems, Fire Alarms, and Signaling Overview 8.7 Motors and Generators Case Lab

9 Chapter 9: Special Occupancies, Renewables, and Safety

9.1 Hazardous Classified Locations 9.2 Healthcare, Marinas, RV Parks, and Mobile Home Parks 9.3 Pools, Spas, and Similar Installations 9.4 Solar PV, Energy Storage, and Renewable Systems 9.5 Temporary Power, Emergency Systems, and Special Conditions 9.6 OSHA Subpart K and Safe Work Practice Context 9.7 Special Occupancies Case Lab

10 Chapter 10: Open-Book Exam Workflow and Mixed Code Labs

10.1 Four-Hour Pacing and Question Triage 10.2 Look-Up vs. Know-From-Memory Decisions 10.3 Mixed Calculation Lab 10.4 Mixed Code Navigation Lab 10.5 Diagnostic Report and Error Log Remediation 10.6 High-Weight Domain Remediation Plan 10.7 Full Exam Simulation Playbook

11 Chapter 11: Final Review, Test Day, and License Planning

11.1 Final Two-Week Study Plan 11.2 Reference Book, Tabs, and Allowed Materials Checklist 11.3 Pearson VUE, PRONTO, and Test-Day Rules 11.4 After the Exam: Results, Retakes, and Challenges 11.5 License Application, Work Hours, and Jurisdiction Next Steps 11.6 After Journeyman: Master, Contractor, and Continuing Education

8.5 Transformer Sizing, Protection, and Grounding

Key Takeaways Explain This Topic AI

Transformer problems require separating primary conductors, transformer overcurrent protection, secondary conductors, and separately derived system grounding.

kVA, voltage, phase, and current formulas drive transformer sizing before conductor and protection tables are used.

Transformer secondary conductors are not automatically protected by the primary overcurrent device and often need specific secondary conductor rule analysis.

Most transformer grounding traps involve the system bonding jumper, grounding electrode conductor, and bonding of metal parts.

Last updated: May 2026

Transformer question map

A transformer changes voltage, but an exam question about a transformer usually asks one of four things: current, overcurrent protection, conductor sizing, or grounding. Treat those as separate paths. Article 450 covers transformer protection and installation rules. Article 240 covers conductor overcurrent protection, including transformer secondary conductor rules. Article 250 covers grounding and bonding for separately derived systems. Article 310 supplies conductor ampacity.

Use this map before doing math:

  • Task First data needed Main navigation
  • Find primary current kVA, primary voltage, phase Transformer current formula
  • Find secondary current kVA, secondary voltage, phase Transformer current formula

Size transformer overcurrent protection Primary/secondary current and transformer type Article 450 tables and rules

Size conductors Calculated current, terminal temperature, conditions Article 310 plus Article 240

Ground a separately derived system Transformer secondary configuration and bonding point Article 250 separately derived system rules

Current formulas

For single-phase transformers:

I = VA / V

For three-phase transformers:

I = VA / (1.732 x V)

Remember that kVA must be converted to VA:

45 kVA = 45,000 VA

Example 1: A 25 kVA single-phase transformer has a 240 V secondary.

I = 25,000 VA / 240 V = 104.2 A

Example 2: A 75 kVA three-phase transformer has a 480 V primary.

I = 75,000 VA / (1.732 x 480 V) = 90.2 A

Those current values are not automatically breaker sizes. They are starting points. The question must say whether it wants current, conductor ampacity, overcurrent device rating, or equipment grounding conductor size.

Transformer overcurrent protection

Transformer overcurrent protection is addressed in Article 450. The allowed primary and secondary protection depends on transformer type, voltage, current, and whether protection is primary-only or primary-and-secondary. The table navigation is more important than memorizing every percentage. Read the row and notes carefully.

A common error is applying ordinary conductor protection rules directly to the transformer without checking Article 450. Another error is stopping at Article 450 and forgetting that the conductors connected to the transformer have their own protection requirements. Transformer protection and conductor protection overlap, but they are not identical.

When the calculated overcurrent size does not match a standard rating, Article 450 and Article 240 rules may allow a next standard size in specific circumstances. Do not automatically round up every transformer number. The permissive rule must exist for the condition in the stem.

Secondary conductors

Transformer secondary conductors are a major trap. The primary overcurrent device protects the transformer primary circuit and may protect the transformer in some arrangements, but it does not automatically protect every secondary conductor from overload or short circuit in the way a branch-circuit breaker protects downstream conductors. Article 240 has specific secondary conductor rules with length limits, installation conditions, termination requirements, and overcurrent protection placement.

Case: A 480 V to 208Y/120 V transformer feeds a panelboard 8 feet away. The secondary conductors may qualify under a transformer secondary conductor rule if all conditions are met. Now move the panelboard 40 feet away through a warehouse. The answer may change because length and protection conditions change. On the exam, pay attention to the exact conductor length.

Separately derived system grounding

A transformer secondary that has no direct electrical connection to the primary conductors is commonly a separately derived system, except for equipment grounding and bonding connections. That means the secondary system needs a grounding and bonding arrangement under Article 250. The system bonding jumper connects the grounded conductor to the equipment grounding conductors and transformer or first disconnect enclosure at the permitted location. A grounding electrode conductor connects the derived system to the grounding electrode system as required.

The usual grounding question is: where is the neutral bonded? It should be bonded at the separately derived system location permitted by Article 250, not repeatedly bonded at every panel downstream. Multiple neutral-to-ground bonds on the load side can place normal neutral current on metal raceways, equipment grounding conductors, and building steel.

Transformer cases

Case 1: A 45 kVA three-phase transformer supplies a 208Y/120 V panel. Secondary current is:

45,000 / (1.732 x 208) = 124.9 A

The candidate then checks conductor ampacity, secondary conductor protection, panel rating, and grounding. The answer is not complete at 125 A unless the question asks only for secondary current.

Case 2: A dry-type transformer is installed in a storage room. Besides electrical sizing, check ventilation, working space, physical protection, sound/vibration concerns, and suitability for the environment. NEC installation rules and manufacturer instructions matter.

Case 3: A separately derived 120/208 V system has the neutral bonded in the transformer and again in the downstream panel. That is a classic objectionable-current trap unless the specific system arrangement allows it. Usually one bonding point is intended for the derived system.

Study workflow

Build a transformer worksheet with four lines: primary current, secondary current, transformer OCP, secondary conductor rule. Add a fifth line for SDS grounding: bonding jumper location, grounding electrode conductor, equipment grounding conductor, and panel neutral isolation. Use the worksheet every time, even for short questions. Consistency prevents mixing Article 450, 240, 250, and 310 in the wrong order.