Study guide

2.6 State Amendments and Code Edition Control

Journeyman Electrician Study Guide Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Exam Orientation and Source Control

1.1 ICC R17, T17, G17, and Jurisdiction Variance 1.2 Current Format, Cost, Time, and Passing Score 1.3 Licensing Board vs. Exam Provider 1.4 Official References, Open-Book Rules, and Calculators 1.5 Domain Weights and Study Map 1.6 Using the Practice Bank, Error Log, and NEC Index

2 Chapter 2: NEC Navigation, Definitions, and Code Strategy

2.1 NEC Book Structure and Article Map 2.2 Article 100 Definitions and Exam Language 2.3 Index, Table, and Annex Navigation 2.4 Shall, Shall Not, Permitted, and Informational Notes 2.5 Using Code References Without Overlooking Context 2.6 State Amendments and Code Edition Control 2.7 NEC Navigation Case Lab

3 Chapter 3: Electrical Theory and Calculation Foundations

3.1 Ohm's Law, Power, and Basic Units 3.2 Series, Parallel, and Circuit Behavior 3.3 Single-Phase, Three-Phase, and Voltage Systems 3.4 Continuous Loads, Demand, and 125 Percent Rules 3.5 Voltage Drop and Practical Calculation Setup 3.6 Load Calculation Workflow 3.7 Calculation Foundation Case Lab

4 Chapter 4: Services, Service Equipment, and Grounding/Bonding

4.1 Service Point, Service Conductors, and Disconnects 4.2 Service Load Calculation and Sizing 4.3 Service Equipment, Panelboards, and Switchboards 4.4 Grounding Electrode System and GEC 4.5 Bonding, Main Bonding Jumpers, and Effective Fault Path 4.6 Transformers and Separately Derived Systems 4.7 Services and Grounding Case Lab

5 Chapter 5: Feeders, Branch Circuits, and Conductor Sizing

5.1 Feeder vs. Branch Circuit Boundaries 5.2 Branch Circuit Ratings and Required Outlets 5.3 Conductor Ampacity, Temperature, and Terminal Ratings 5.4 Adjustment, Correction, and More Than Three Conductors 5.5 Overcurrent Protection and Small-Conductor Rules 5.6 GFCI, AFCI, Equipment Grounding, and Dwelling Circuits 5.7 Feeders and Branch Circuits Case Lab

6 Chapter 6: Wiring Methods, Raceways, Boxes, and Cables

6.1 Raceway Selection and Installation Logic 6.2 Underground Wiring, Wet Locations, and Protection 6.3 Boxes, Enclosures, and Conduit Bodies 6.4 Box Fill, Conductor Counting, and Device Yokes 6.5 Cabinets, Panelboards, and Switchboards 6.6 Flexible Cords, Cables, and Temporary Wiring 6.7 Wiring Methods Case Lab

7 Chapter 7: Equipment, Devices, Luminaires, and Controls

7.1 Receptacles, Switches, and Device Selection 7.2 Luminaires, Lampholders, and Lighting Outlets 7.3 Appliances and Utilization Equipment 7.4 Heating, Cooling, and HVAC Electrical Connections 7.5 Disconnects, Controllers, and Switching Devices 7.6 Equipment Grounding, Bonding, and Listing Markings 7.7 Equipment and Devices Case Lab

8 Chapter 8: Motors, Generators, Transformers, and Special Equipment

8.1 Motor Circuit Anatomy and Article 430 Navigation 8.2 Motor Conductors, Overload, and Short-Circuit Protection 8.3 Motor Controllers, Disconnects, and Nameplates 8.4 Generators, Transfer Equipment, and Optional Standby 8.5 Transformer Sizing, Protection, and Grounding 8.6 Emergency Systems, Fire Alarms, and Signaling Overview 8.7 Motors and Generators Case Lab

9 Chapter 9: Special Occupancies, Renewables, and Safety

9.1 Hazardous Classified Locations 9.2 Healthcare, Marinas, RV Parks, and Mobile Home Parks 9.3 Pools, Spas, and Similar Installations 9.4 Solar PV, Energy Storage, and Renewable Systems 9.5 Temporary Power, Emergency Systems, and Special Conditions 9.6 OSHA Subpart K and Safe Work Practice Context 9.7 Special Occupancies Case Lab

10 Chapter 10: Open-Book Exam Workflow and Mixed Code Labs

10.1 Four-Hour Pacing and Question Triage 10.2 Look-Up vs. Know-From-Memory Decisions 10.3 Mixed Calculation Lab 10.4 Mixed Code Navigation Lab 10.5 Diagnostic Report and Error Log Remediation 10.6 High-Weight Domain Remediation Plan 10.7 Full Exam Simulation Playbook

11 Chapter 11: Final Review, Test Day, and License Planning

11.1 Final Two-Week Study Plan 11.2 Reference Book, Tabs, and Allowed Materials Checklist 11.3 Pearson VUE, PRONTO, and Test-Day Rules 11.4 After the Exam: Results, Retakes, and Challenges 11.5 License Application, Work Hours, and Jurisdiction Next Steps 11.6 After Journeyman: Master, Contractor, and Continuing Education

2.6 State Amendments and Code Edition Control

Key Takeaways Explain This Topic AI

ICC provides contractor and trades exams, but state or local licensing agencies decide license requirements.

R17-N is tied to the 2023 NEC, T17-N to the 2020 NEC, and G17-N to the 2017 NEC in the current ICC national exam list described in the source brief.

Always study the NEC edition, approved references, open-book rules, and amendments named by the exam catalog or jurisdiction.

State and local amendments can change requirements from the base NEC, especially for licensing exams administered or adopted by a jurisdiction.

Do not mix editions during final review unless you are deliberately comparing changes.

Last updated: May 2026

ICC exam does not equal license

The ICC National Standard Journeyman Electrician exams are contractor and trades exams used by licensing agencies, but ICC is not the licensing board for every candidate. Passing an ICC exam does not automatically grant a journeyman license. The agency with authority where you want to work decides whether you need the ICC exam, a state exam, local registration, apprenticeship hours, experience verification, fees, continuing education, background checks, or additional trade classifications.

This distinction matters for study planning. The NEC-centered content may be similar across many jurisdictions, but administrative requirements vary. One state may use an ICC exam directly. Another may use its own exam vendor. A city or county may add local amendments or separate business licensing. Some jurisdictions may require a different code edition than the one your coworker studied. Before spending weeks with a book, confirm the exact exam ID, code edition, approved references, and license path.

  • Item to verify Why it matters
  • Exam ID R17-N, T17-N, G17-N, or a jurisdiction-specific exam may use different references
  • NEC edition Section numbers, article structure, and requirements can change by edition
  • Approved references Appeals and answers are based on listed references, not random study notes
  • Open-book status Determines how much navigation speed matters on test day
  • Tab and note rules Bound notes and permanent tabs may be allowed, while loose papers often are not
  • Retake and score rules Contractor/trades policies can differ from certification programs or board rules
  • State amendments The jurisdiction may add, delete, or revise base NEC requirements
  • Edition control for R17, T17, and G17

The source brief identifies current ICC national journeyman electrician exam listings as G17-N for the 2017 NEC, T17-N for the 2020 NEC, and R17-N for the 2023 NEC. These are not interchangeable labels. If you register for R17-N, study from the 2023 NEC and the approved references listed for that exam. If your jurisdiction requires T17-N or G17-N, use that edition instead. Do not assume the newest NEC is the tested source unless the exam catalog says so.

Edition mixing creates subtle errors. A rule you learned from 2023 may have different numbering or wording in 2020 or 2017. A section may be reorganized, an exception may move, a defined term may change, and a table reference may shift. Even when the practical field result is similar, the exam answer must align with the reference edition. During final review, keep one primary code book and one set of tabs for the scheduled exam.

A simple source-control label helps. Write your target exam at the top of your study plan: R17-N, 2023 NEC, ICC contractor/trades, open book, 80 questions, 4 hours. Or write T17-N, 2020 NEC. Or write G17-N, 2017 NEC. Add the jurisdiction name and any local amendment source. This prevents accidental switching when you watch videos, read forums, or borrow notes.

Amendments and local rules

The NEC is a model code. Jurisdictions adopt it and may amend it. Amendments can add local requirements, delete sections, modify effective dates, or change administrative enforcement. They may address service equipment, grounding, smoke alarms, energy systems, permitting, inspection, or regional hazards. The authority having jurisdiction interprets and enforces adopted requirements.

For an ICC national contractor exam, questions come from the listed references in the exam catalog. For a state or local journeyman exam, the jurisdiction may include amendments as tested material. That means the correct study workflow is not simply buy an NEC and start tabbing. It is: confirm the exam, pull the official bulletin or candidate handbook, list every reference, check whether amendments are included, and then build your tabs and notes around those sources.

Handling conflicting study materials

You will see conflicting answers online. Some are from another NEC edition. Some are from local amendments. Some are from a master electrician exam instead of a journeyman exam. Some are from OSHA safety standards, which are important but do not replace the NEC for a code question unless the exam reference says so. Some are from field practice that exceeds minimum code. Strong candidates learn to ask: what source is this answer based on?

When two sources disagree, rank them by exam authority:

Current candidate bulletin or exam catalog for your scheduled exam.

Approved code edition and listed references for that exam.

Jurisdiction amendments if the jurisdiction says they are tested.

Official errata or updates from the issuing organization.

Study guides, classes, videos, and forums as secondary learning aids.

This does not mean study aids are useless. They are valuable for explanation, drills, and memory. But they should not override the code edition and reference list that govern your score.

Exam logistics as source control

The ICC contractor/trades bulletin described in the brief states that exam details are subject to change and candidates should use current bulletins and catalogs. It also describes four-option multiple-choice questions, no guessing penalty, and the need for reference familiarity because there is not enough time to look up every answer. Results are generally available immediately for electronic testing, and failed exam retakes generally require a waiting period unless the licensing board says otherwise.

Passing score guidance for contractor/trades exams is generally 70 percent, while master electrician scoring can differ.

Use logistics to shape practice. If the exam is 80 questions in 4 hours, average time is 3 minutes per question. Some questions should take 20 seconds because you know the concept. Some calculations may take several minutes. If you spend 5 minutes proving a low-value definition question, you are borrowing time from a motor or service calculation. Source control and time control work together.

The best rule is simple: study for the exam you actually registered for, in the jurisdiction that will issue or recognize your license. The NEC is national in influence, but licensing is local in authority.