Study guide

10.6 High-Weight Domain Remediation Plan

Journeyman Electrician Study Guide Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Exam Orientation and Source Control

1.1 ICC R17, T17, G17, and Jurisdiction Variance 1.2 Current Format, Cost, Time, and Passing Score 1.3 Licensing Board vs. Exam Provider 1.4 Official References, Open-Book Rules, and Calculators 1.5 Domain Weights and Study Map 1.6 Using the Practice Bank, Error Log, and NEC Index

2 Chapter 2: NEC Navigation, Definitions, and Code Strategy

2.1 NEC Book Structure and Article Map 2.2 Article 100 Definitions and Exam Language 2.3 Index, Table, and Annex Navigation 2.4 Shall, Shall Not, Permitted, and Informational Notes 2.5 Using Code References Without Overlooking Context 2.6 State Amendments and Code Edition Control 2.7 NEC Navigation Case Lab

3 Chapter 3: Electrical Theory and Calculation Foundations

3.1 Ohm's Law, Power, and Basic Units 3.2 Series, Parallel, and Circuit Behavior 3.3 Single-Phase, Three-Phase, and Voltage Systems 3.4 Continuous Loads, Demand, and 125 Percent Rules 3.5 Voltage Drop and Practical Calculation Setup 3.6 Load Calculation Workflow 3.7 Calculation Foundation Case Lab

4 Chapter 4: Services, Service Equipment, and Grounding/Bonding

4.1 Service Point, Service Conductors, and Disconnects 4.2 Service Load Calculation and Sizing 4.3 Service Equipment, Panelboards, and Switchboards 4.4 Grounding Electrode System and GEC 4.5 Bonding, Main Bonding Jumpers, and Effective Fault Path 4.6 Transformers and Separately Derived Systems 4.7 Services and Grounding Case Lab

5 Chapter 5: Feeders, Branch Circuits, and Conductor Sizing

5.1 Feeder vs. Branch Circuit Boundaries 5.2 Branch Circuit Ratings and Required Outlets 5.3 Conductor Ampacity, Temperature, and Terminal Ratings 5.4 Adjustment, Correction, and More Than Three Conductors 5.5 Overcurrent Protection and Small-Conductor Rules 5.6 GFCI, AFCI, Equipment Grounding, and Dwelling Circuits 5.7 Feeders and Branch Circuits Case Lab

6 Chapter 6: Wiring Methods, Raceways, Boxes, and Cables

6.1 Raceway Selection and Installation Logic 6.2 Underground Wiring, Wet Locations, and Protection 6.3 Boxes, Enclosures, and Conduit Bodies 6.4 Box Fill, Conductor Counting, and Device Yokes 6.5 Cabinets, Panelboards, and Switchboards 6.6 Flexible Cords, Cables, and Temporary Wiring 6.7 Wiring Methods Case Lab

7 Chapter 7: Equipment, Devices, Luminaires, and Controls

7.1 Receptacles, Switches, and Device Selection 7.2 Luminaires, Lampholders, and Lighting Outlets 7.3 Appliances and Utilization Equipment 7.4 Heating, Cooling, and HVAC Electrical Connections 7.5 Disconnects, Controllers, and Switching Devices 7.6 Equipment Grounding, Bonding, and Listing Markings 7.7 Equipment and Devices Case Lab

8 Chapter 8: Motors, Generators, Transformers, and Special Equipment

8.1 Motor Circuit Anatomy and Article 430 Navigation 8.2 Motor Conductors, Overload, and Short-Circuit Protection 8.3 Motor Controllers, Disconnects, and Nameplates 8.4 Generators, Transfer Equipment, and Optional Standby 8.5 Transformer Sizing, Protection, and Grounding 8.6 Emergency Systems, Fire Alarms, and Signaling Overview 8.7 Motors and Generators Case Lab

9 Chapter 9: Special Occupancies, Renewables, and Safety

9.1 Hazardous Classified Locations 9.2 Healthcare, Marinas, RV Parks, and Mobile Home Parks 9.3 Pools, Spas, and Similar Installations 9.4 Solar PV, Energy Storage, and Renewable Systems 9.5 Temporary Power, Emergency Systems, and Special Conditions 9.6 OSHA Subpart K and Safe Work Practice Context 9.7 Special Occupancies Case Lab

10 Chapter 10: Open-Book Exam Workflow and Mixed Code Labs

10.1 Four-Hour Pacing and Question Triage 10.2 Look-Up vs. Know-From-Memory Decisions 10.3 Mixed Calculation Lab 10.4 Mixed Code Navigation Lab 10.5 Diagnostic Report and Error Log Remediation 10.6 High-Weight Domain Remediation Plan 10.7 Full Exam Simulation Playbook

11 Chapter 11: Final Review, Test Day, and License Planning

11.1 Final Two-Week Study Plan 11.2 Reference Book, Tabs, and Allowed Materials Checklist 11.3 Pearson VUE, PRONTO, and Test-Day Rules 11.4 After the Exam: Results, Retakes, and Challenges 11.5 License Application, Work Hours, and Jurisdiction Next Steps 11.6 After Journeyman: Master, Contractor, and Continuing Education

10.6 High-Weight Domain Remediation Plan

Key Takeaways Explain This Topic AI

Remediation should prioritize repeated misses in high-weight domains before isolated misses in low-weight domains.

Wiring Methods and Materials, Branch Circuits and Conductors, Equipment and Devices, Services, and Special Occupancies carry most of the shared ICC journeyman outline.

Each high-weight domain needs a different drill mix: navigation, calculations, field cases, tables, and answer-choice elimination.

A remediation plan should end with timed mixed sets, not just rereading chapters.

Last updated: May 2026

Weight drives priority

The shared R17, T17, and G17 domain outline is not just background information. It is a study budgeting tool. If you have two weak areas and only one week before the exam, the domain with more likely questions usually gets the first repair block. This is especially true when a high-weight domain also creates errors in other domains.

The source brief lists these shared weights:

  • Domain Weight Study priority when weak
  • Wiring Methods and Materials 26 percent Highest
  • Branch Circuits and Conductors 19 percent Highest
  • Equipment and Devices 13 percent High
  • Services and Service Equipment 11 percent High
  • Special Occupancies, Equipment, and Conditions 11 percent High
  • General Knowledge 6 percent Medium
  • Motors and Generators 6 percent Medium
  • Feeders 4 percent Targeted
  • Control Devices 4 percent Targeted

This does not mean you ignore feeders or control devices. It means a candidate missing half of Wiring Methods should not spend the entire weekend polishing a rare control-device fact. Use weights to decide sequence, not to excuse gaps.

Wiring Methods and Materials plan

This is the largest domain, so it deserves the most applied practice. Build a comparison grid for the raceway and cable methods you expect to see: EMT, RMC, IMC, PVC, FMC, LFMC, MC cable, NM cable, UF cable, and related methods from your edition. For each method, record permitted uses, not permitted uses, wet-location concerns, support route, grounding or bonding notes, physical-damage concerns, and fill path.

Drill mix: 40 percent navigation, 30 percent field cases, 20 percent raceway and box calculations, 10 percent definitions. A strong drill asks: Can this wiring method be used here, what else must be true, and where does the answer live? Wrong answers often rely on a method being common in the field but not permitted under the stated condition.

Branch Circuits and Conductors plan

Branch-circuit work blends load, conductor ampacity, overcurrent protection, receptacle and outlet rules, required circuits, continuous load, conductor identification, and GFCI or AFCI style protection depending on location and edition. Start with Article 210 route fluency, then connect to Article 310 for conductors and Article 240 for overcurrent protection.

Drill mix: 35 percent code navigation, 35 percent calculations, 20 percent dwelling or occupancy location cases, 10 percent protection-device distinctions. Practice reading the last sentence carefully. A stem may include conductor size but ask for required receptacle protection. Another may mention a kitchen but ask for small-appliance branch-circuit quantity or load calculation. Classify before answering.

Equipment and Devices plan

Equipment and device questions often test boxes, receptacles, luminaires, disconnects, utilization equipment, working space, listing, and installation according to instructions. This domain rewards field thinking. Ask what the equipment is, who must access it, what environment it is in, and what protection or listing applies.

Drill mix: 30 percent Article 110 and equipment listing, 25 percent receptacles and devices, 20 percent boxes and supports, 15 percent disconnects and working space, 10 percent wet or damp location cases. When a question mentions a device yoke, luminaire box, ceiling fan, in-use cover, or disconnecting means, slow down. The issue is usually not conductor ampacity alone.

Services and Service Equipment plan

Services are high-consequence and conceptually dense. Repair work should separate service conductors, service disconnects, service equipment, grounding electrode conductors, bonding, grounded conductors, service raceways, and available fault current. Many errors come from applying feeder or subpanel logic to service equipment.

Drill mix: 35 percent service navigation, 25 percent grounding and bonding, 20 percent conductor and equipment sizing, 10 percent disconnect location and grouping, 10 percent field diagrams. Draw simple one-line diagrams. Mark utility side, service point if given, service conductors, service disconnect, main bonding jumper, grounding electrode conductor, feeder, and branch circuits. Visual separation helps prevent rule mixing.

Special Occupancies, Equipment, and Conditions plan

This domain includes special locations, equipment, and systems where ordinary assumptions may fail. Examples can include hazardous classified locations, health care, marinas, RVs, pools, agricultural buildings, emergency systems, optional standby systems, solar photovoltaic systems, and other NEC special articles depending on the exam outline and edition. The goal is not to memorize every special article. The goal is to recognize when a special article applies and how it overlays the base rule.

Drill mix: 50 percent article recognition and scope, 20 percent wiring method and equipment marking, 15 percent grounding or bonding overlays, 15 percent disconnects, signs, and special protection. For each special article, learn the first-page scope and definitions. Many questions are won by knowing whether the article applies before looking for details.

Medium and targeted domains

General Knowledge and Motors and Generators are medium-weight domains in the shared outline. General Knowledge often supports everything else: definitions, safety, plan reading, and general NEC application. Motors need Article 430 route practice because conductor sizing, overloads, short-circuit and ground-fault protection, disconnects, and controllers are separate tasks. Feeders and Control Devices are lower weight but should receive targeted repair if missed repeatedly.

A practical weekly plan might allocate 3 blocks to Wiring Methods, 2 to Branch Circuits, 1 to Services, 1 to Equipment, 1 to Special Occupancies, and rotating shorter blocks to motors, feeders, control devices, and general knowledge. Adjust based on your error log. Weight matters, but repeated misses matter too.

Finish with mixed performance

After remediation blocks, run a timed mixed set. Do not declare a domain fixed because you reread it. A fixed domain should show three improvements: faster route, better explanation, and higher fresh-question accuracy. For high-weight areas, require performance under time pressure. The actual exam will not present all wiring-method questions together in a friendly order.

The final plan should be written on one page: weak domain, cause, drill, scheduled date, target score, and retest result. If the plan cannot fit on one page, it is probably too vague.