Study guide

10.3 Mixed Calculation Lab

Journeyman Electrician Study Guide Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Exam Orientation and Source Control

1.1 ICC R17, T17, G17, and Jurisdiction Variance 1.2 Current Format, Cost, Time, and Passing Score 1.3 Licensing Board vs. Exam Provider 1.4 Official References, Open-Book Rules, and Calculators 1.5 Domain Weights and Study Map 1.6 Using the Practice Bank, Error Log, and NEC Index

2 Chapter 2: NEC Navigation, Definitions, and Code Strategy

2.1 NEC Book Structure and Article Map 2.2 Article 100 Definitions and Exam Language 2.3 Index, Table, and Annex Navigation 2.4 Shall, Shall Not, Permitted, and Informational Notes 2.5 Using Code References Without Overlooking Context 2.6 State Amendments and Code Edition Control 2.7 NEC Navigation Case Lab

3 Chapter 3: Electrical Theory and Calculation Foundations

3.1 Ohm's Law, Power, and Basic Units 3.2 Series, Parallel, and Circuit Behavior 3.3 Single-Phase, Three-Phase, and Voltage Systems 3.4 Continuous Loads, Demand, and 125 Percent Rules 3.5 Voltage Drop and Practical Calculation Setup 3.6 Load Calculation Workflow 3.7 Calculation Foundation Case Lab

4 Chapter 4: Services, Service Equipment, and Grounding/Bonding

4.1 Service Point, Service Conductors, and Disconnects 4.2 Service Load Calculation and Sizing 4.3 Service Equipment, Panelboards, and Switchboards 4.4 Grounding Electrode System and GEC 4.5 Bonding, Main Bonding Jumpers, and Effective Fault Path 4.6 Transformers and Separately Derived Systems 4.7 Services and Grounding Case Lab

5 Chapter 5: Feeders, Branch Circuits, and Conductor Sizing

5.1 Feeder vs. Branch Circuit Boundaries 5.2 Branch Circuit Ratings and Required Outlets 5.3 Conductor Ampacity, Temperature, and Terminal Ratings 5.4 Adjustment, Correction, and More Than Three Conductors 5.5 Overcurrent Protection and Small-Conductor Rules 5.6 GFCI, AFCI, Equipment Grounding, and Dwelling Circuits 5.7 Feeders and Branch Circuits Case Lab

6 Chapter 6: Wiring Methods, Raceways, Boxes, and Cables

6.1 Raceway Selection and Installation Logic 6.2 Underground Wiring, Wet Locations, and Protection 6.3 Boxes, Enclosures, and Conduit Bodies 6.4 Box Fill, Conductor Counting, and Device Yokes 6.5 Cabinets, Panelboards, and Switchboards 6.6 Flexible Cords, Cables, and Temporary Wiring 6.7 Wiring Methods Case Lab

7 Chapter 7: Equipment, Devices, Luminaires, and Controls

7.1 Receptacles, Switches, and Device Selection 7.2 Luminaires, Lampholders, and Lighting Outlets 7.3 Appliances and Utilization Equipment 7.4 Heating, Cooling, and HVAC Electrical Connections 7.5 Disconnects, Controllers, and Switching Devices 7.6 Equipment Grounding, Bonding, and Listing Markings 7.7 Equipment and Devices Case Lab

8 Chapter 8: Motors, Generators, Transformers, and Special Equipment

8.1 Motor Circuit Anatomy and Article 430 Navigation 8.2 Motor Conductors, Overload, and Short-Circuit Protection 8.3 Motor Controllers, Disconnects, and Nameplates 8.4 Generators, Transfer Equipment, and Optional Standby 8.5 Transformer Sizing, Protection, and Grounding 8.6 Emergency Systems, Fire Alarms, and Signaling Overview 8.7 Motors and Generators Case Lab

9 Chapter 9: Special Occupancies, Renewables, and Safety

9.1 Hazardous Classified Locations 9.2 Healthcare, Marinas, RV Parks, and Mobile Home Parks 9.3 Pools, Spas, and Similar Installations 9.4 Solar PV, Energy Storage, and Renewable Systems 9.5 Temporary Power, Emergency Systems, and Special Conditions 9.6 OSHA Subpart K and Safe Work Practice Context 9.7 Special Occupancies Case Lab

10 Chapter 10: Open-Book Exam Workflow and Mixed Code Labs

10.1 Four-Hour Pacing and Question Triage 10.2 Look-Up vs. Know-From-Memory Decisions 10.3 Mixed Calculation Lab 10.4 Mixed Code Navigation Lab 10.5 Diagnostic Report and Error Log Remediation 10.6 High-Weight Domain Remediation Plan 10.7 Full Exam Simulation Playbook

11 Chapter 11: Final Review, Test Day, and License Planning

11.1 Final Two-Week Study Plan 11.2 Reference Book, Tabs, and Allowed Materials Checklist 11.3 Pearson VUE, PRONTO, and Test-Day Rules 11.4 After the Exam: Results, Retakes, and Challenges 11.5 License Application, Work Hours, and Jurisdiction Next Steps 11.6 After Journeyman: Master, Contractor, and Continuing Education

10.3 Mixed Calculation Lab

Key Takeaways Explain This Topic AI

Mixed calculation questions should be classified before solving: load, conductor ampacity, box fill, raceway fill, motor, overcurrent, or voltage-drop style.

Most exam math errors come from using the right formula on the wrong code object, such as feeder instead of branch circuit or box fill instead of conduit fill.

A written setup line prevents table, unit, and rounding mistakes under time pressure.

Calculation review should focus on inputs, units, table rows, and whether the question asks for minimum, maximum, permitted, or required.

Last updated: May 2026

Classify before calculating

The fastest way to miss an electrical calculation is to start arithmetic before naming the problem. Mixed exam questions often include extra facts: conductor material, raceway type, continuous load, dwelling or non-dwelling use, motor horsepower, number of conductors, wet location, or service equipment. Some facts matter. Some are distractors. Your first job is to classify the calculation.

Use this classification table:

  • Calculation type Main question Common NEC path
  • Load How many volt-amperes or amperes are supplied? Article 220 and equipment rules
  • Ampacity What conductor size is adequate? Article 310, conditions of use, Article 240 check
  • Box fill Is the box volume sufficient? Article 314
  • Raceway fill Can the conductors fit in the raceway? Chapter 9 and wiring method article
  • Motor What current value controls conductors or protection? Article 430 tables and rules
  • Service or feeder What minimum conductor or equipment rating is required? Articles 215, 220, 230, 240, 250
  • Voltage drop What is the practical performance impact? Formula and informational guidance where applicable

Write one setup line before solving. Example: Box fill: 12 AWG conductors, count equivalents, compare required cubic inches to box marking. Another example: Motor branch circuit: use table full-load current, then apply conductor percentage, then check protection rule. This line keeps you from mixing formulas.

Lab case 1: branch-circuit load and continuous use

A commercial sign load is 12 amperes at 120 volts and is expected to operate for more than 3 hours. The stem asks for the minimum branch-circuit rating before conductor adjustment complications. The recognition step is continuous load. The setup is 12 A x 125 percent = 15 A . If answer choices include 12 A, 15 A, 20 A, and 30 A, the minimum rating from the continuous-load adjustment is 15 A, subject to standard circuit and equipment rules in the full code context.

Exam trap: do not multiply volts by amperes if the question already asks for branch-circuit ampere rating. Also do not jump to 20 amperes unless the code context requires a standard branch-circuit rating or the answer choices force the next standard size. Read the wording: minimum calculated load, minimum rating, conductor ampacity, and overcurrent device rating can produce different final answers.

Lab case 2: box fill

A metal device box contains two 12 AWG ungrounded conductors spliced together, two 12 AWG neutrals spliced together, two 12 AWG equipment grounding conductors, one internal cable clamp, and one single-gang receptacle yoke with 12 AWG conductors connected. Classify it as box fill. Count the conductor equivalents under Article 314 logic.

The ungrounded conductors count, the neutrals count, the equipment grounding conductors together usually count as one equivalent of the largest equipment grounding conductor, the internal clamp counts as an allowance, and the device yoke adds its allowance based on connected conductor size.

The arithmetic is not hard after the count is right. The common error is counting equipment grounding conductors one-for-one or forgetting the device yoke. Another error is using raceway fill tables because the word conductors appears. Box fill is volume in cubic inches. Raceway fill is area in a raceway. Same conductors, different problem.

Lab case 3: raceway fill

A question gives a raceway type, trade size, and number of THHN conductors. The setup is raceway fill: conductor area x count, compare to allowed raceway area for more than two conductors. The answer path is Chapter 9: find conductor area, find raceway area, apply the correct fill percentage and notes. Annex C may provide a shortcut for common conductor and raceway combinations if it is allowed in your reference use, but Chapter 9 tables remain the defensible method.

Trap: conductor ampacity adjustment for more than three current-carrying conductors is a separate question. Raceway fill tells you whether the conductors physically fit. Ampacity adjustment tells you whether the conductors can carry the load under conditions of use. A mixed stem may ask both, but do not substitute one for the other.

Lab case 4: motor question

Motor questions are famous for using table full-load current instead of nameplate current for some sizing steps. The setup line should identify the controlled item: branch-circuit conductor, short-circuit and ground-fault protection, overload protection, disconnect, or feeder. Article 430 is organized around those functions. A question asking conductor ampacity is not the same as one asking maximum inverse-time breaker size.

A typical workflow is: identify motor type, phase, voltage, and horsepower; find the table current when required; apply the percentage for the item being sized; then apply standard sizing or exception logic if the rule directs it. Do not use dwelling load shortcuts on a motor problem. Do not use the nameplate current unless the rule for that item calls for it.

Lab case 5: voltage-drop style arithmetic

Voltage drop is often taught with formulas such as VD = 2 x K x I x D / CM for single-phase two-wire circuits and a related three-phase formula using 1.732. On many journeyman exams, voltage drop appears as a practical design or recommended-performance calculation rather than a strict overcurrent sizing rule. The exam may still require arithmetic, unit discipline, and recognition that circular mil area, one-way distance, current, and conductor material matter.

If the stem asks what conductor reduces voltage drop, the larger conductor usually helps because resistance falls as circular mil area rises. If the stem asks whether the overcurrent device can be enlarged merely because voltage drop is high, be careful. Overcurrent protection is based on conductor ampacity and equipment rules, not on hiding voltage drop with a larger breaker.

Calculation review checklist

Before changing a calculation answer, check these five items: object, units, table, multiplier, and wording. Object means branch circuit, feeder, service, motor, box, or raceway. Units means amperes, volt-amperes, watts, cubic inches, square inches, circular mils, or feet. Table means you used the correct edition and row. Multiplier means continuous load, conductor count, motor percentage, or demand factor. Wording means minimum, maximum, nearest, not less than, not more than, or permitted.

A calculation that passes those five checks is usually stronger than a last-minute hunch. If it fails one check, fix the setup first, not just the arithmetic.