Study guide
9.2 Healthcare, Marinas, RV Parks, and Mobile Home Parks
Journeyman Electrician Study Guide Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Exam Orientation and Source Control
1.1 ICC R17, T17, G17, and Jurisdiction Variance 1.2 Current Format, Cost, Time, and Passing Score 1.3 Licensing Board vs. Exam Provider 1.4 Official References, Open-Book Rules, and Calculators 1.5 Domain Weights and Study Map 1.6 Using the Practice Bank, Error Log, and NEC Index
2 Chapter 2: NEC Navigation, Definitions, and Code Strategy
2.1 NEC Book Structure and Article Map 2.2 Article 100 Definitions and Exam Language 2.3 Index, Table, and Annex Navigation 2.4 Shall, Shall Not, Permitted, and Informational Notes 2.5 Using Code References Without Overlooking Context 2.6 State Amendments and Code Edition Control 2.7 NEC Navigation Case Lab
3 Chapter 3: Electrical Theory and Calculation Foundations
3.1 Ohm's Law, Power, and Basic Units 3.2 Series, Parallel, and Circuit Behavior 3.3 Single-Phase, Three-Phase, and Voltage Systems 3.4 Continuous Loads, Demand, and 125 Percent Rules 3.5 Voltage Drop and Practical Calculation Setup 3.6 Load Calculation Workflow 3.7 Calculation Foundation Case Lab
4 Chapter 4: Services, Service Equipment, and Grounding/Bonding
4.1 Service Point, Service Conductors, and Disconnects 4.2 Service Load Calculation and Sizing 4.3 Service Equipment, Panelboards, and Switchboards 4.4 Grounding Electrode System and GEC 4.5 Bonding, Main Bonding Jumpers, and Effective Fault Path 4.6 Transformers and Separately Derived Systems 4.7 Services and Grounding Case Lab
5 Chapter 5: Feeders, Branch Circuits, and Conductor Sizing
5.1 Feeder vs. Branch Circuit Boundaries 5.2 Branch Circuit Ratings and Required Outlets 5.3 Conductor Ampacity, Temperature, and Terminal Ratings 5.4 Adjustment, Correction, and More Than Three Conductors 5.5 Overcurrent Protection and Small-Conductor Rules 5.6 GFCI, AFCI, Equipment Grounding, and Dwelling Circuits 5.7 Feeders and Branch Circuits Case Lab
6 Chapter 6: Wiring Methods, Raceways, Boxes, and Cables
6.1 Raceway Selection and Installation Logic 6.2 Underground Wiring, Wet Locations, and Protection 6.3 Boxes, Enclosures, and Conduit Bodies 6.4 Box Fill, Conductor Counting, and Device Yokes 6.5 Cabinets, Panelboards, and Switchboards 6.6 Flexible Cords, Cables, and Temporary Wiring 6.7 Wiring Methods Case Lab
7 Chapter 7: Equipment, Devices, Luminaires, and Controls
7.1 Receptacles, Switches, and Device Selection 7.2 Luminaires, Lampholders, and Lighting Outlets 7.3 Appliances and Utilization Equipment 7.4 Heating, Cooling, and HVAC Electrical Connections 7.5 Disconnects, Controllers, and Switching Devices 7.6 Equipment Grounding, Bonding, and Listing Markings 7.7 Equipment and Devices Case Lab
8 Chapter 8: Motors, Generators, Transformers, and Special Equipment
8.1 Motor Circuit Anatomy and Article 430 Navigation 8.2 Motor Conductors, Overload, and Short-Circuit Protection 8.3 Motor Controllers, Disconnects, and Nameplates 8.4 Generators, Transfer Equipment, and Optional Standby 8.5 Transformer Sizing, Protection, and Grounding 8.6 Emergency Systems, Fire Alarms, and Signaling Overview 8.7 Motors and Generators Case Lab
9 Chapter 9: Special Occupancies, Renewables, and Safety
9.1 Hazardous Classified Locations 9.2 Healthcare, Marinas, RV Parks, and Mobile Home Parks 9.3 Pools, Spas, and Similar Installations 9.4 Solar PV, Energy Storage, and Renewable Systems 9.5 Temporary Power, Emergency Systems, and Special Conditions 9.6 OSHA Subpart K and Safe Work Practice Context 9.7 Special Occupancies Case Lab
10 Chapter 10: Open-Book Exam Workflow and Mixed Code Labs
10.1 Four-Hour Pacing and Question Triage 10.2 Look-Up vs. Know-From-Memory Decisions 10.3 Mixed Calculation Lab 10.4 Mixed Code Navigation Lab 10.5 Diagnostic Report and Error Log Remediation 10.6 High-Weight Domain Remediation Plan 10.7 Full Exam Simulation Playbook
11 Chapter 11: Final Review, Test Day, and License Planning
11.1 Final Two-Week Study Plan 11.2 Reference Book, Tabs, and Allowed Materials Checklist 11.3 Pearson VUE, PRONTO, and Test-Day Rules 11.4 After the Exam: Results, Retakes, and Challenges 11.5 License Application, Work Hours, and Jurisdiction Next Steps 11.6 After Journeyman: Master, Contractor, and Continuing Education
9.2 Healthcare, Marinas, RV Parks, and Mobile Home Parks
Key Takeaways Explain This Topic AI
Healthcare wiring questions focus on patient risk, redundant grounding paths, essential electrical systems, receptacle rules, and wet procedure locations.
Marinas and boatyards add shore power, ground-fault protection, corrosion, wet-location equipment, and bonding concerns.
RV parks and mobile home parks require service and feeder logic, pedestal equipment, grounding, disconnecting means, and demand calculations from the correct article.
These occupancies use special NEC articles because ordinary commercial or dwelling assumptions can be unsafe or incomplete.
Last updated: May 2026
Why these occupancies get special rules
The NEC has special occupancy articles because some places create risks that ordinary wiring rules do not fully address. A patient connected to medical equipment is more vulnerable to leakage current than a healthy person standing in an office. A marina combines people, water, metal boats, shore power, corrosion, and long feeder runs. RV parks and mobile home parks look like small utility systems, with pedestals, feeders, outdoor equipment, disconnects, and calculated demand.
Use this article map:
Occupancy Primary exam concern Code-navigation habit
Healthcare facilities Patient care spaces, redundant grounding, essential systems Start in healthcare article, then coordinate with Article 250, 517 branch rules, and equipment articles
Marinas and boatyards Shore power, GFCI or ground-fault protection, wet locations, corrosion Start in marina article, then check wiring methods, grounding, bonding, and receptacle equipment
RV parks Site supply equipment, receptacles, feeders, demand Start in RV park article, then coordinate with services, feeders, and grounding
Mobile home parks Individual home supply, disconnects, feeders, grounding Start in mobile home article, then verify service and feeder rules
The exam often gives the occupancy in the first sentence and then distracts you with a familiar device. If the stem says patient care vicinity, marina shore power pedestal, RV site, or mobile home park feeder, do not answer from the normal commercial branch-circuit rule alone.
Healthcare facilities
Healthcare rules are based on patient risk. Patient care spaces, patient bed locations, operating rooms, critical care spaces, and wet procedure locations each raise different concerns. The exam may not require deep hospital design, but it can test the concept that patient care areas often require a reliable equipment grounding path and wiring methods that provide an effective ground-fault return path. Redundant grounding is not just a green wire preference; it supports fast clearing of faults near patients.
Healthcare questions may mention hospital-grade receptacles, isolated ground receptacles, emergency systems, essential electrical systems, branch categories, or wet procedure locations. Do not assume hospital-grade devices solve every requirement. Device listing, branch type, circuit source, grounding path, receptacle quantity, GFCI protection where required, and transfer to essential power may all be separate issues.
A navigation path for a healthcare stem is: identify the patient care space, determine whether the circuit is normal power or part of the essential electrical system, check wiring method and grounding requirements, then check receptacle or equipment rules. If the question mentions a nursing home, clinic, dental office, or hospital, verify whether the space actually qualifies as a patient care space before applying the strictest hospital rule.
Marinas and boatyards
Marina questions are built around electricity near water and boats. Shore power equipment supplies floating or fixed docks, pedestals, receptacles, boats, and associated equipment. The hazards include electric shock drowning, damaged flexible cords, leakage current, corrosion, movement of docks, and wet-location exposure. The correct answer usually requires listed marina equipment, suitable enclosures, correct grounding and bonding, and the specific ground-fault protection required by the article.
Do not apply ordinary outdoor receptacle thinking and stop there. A marina pedestal may need special protection, ratings, and disconnecting means. Wiring methods must handle wet locations, corrosion, mechanical movement, and physical damage. Metal parts may need bonding so dangerous voltage gradients do not develop. A long dock feeder also raises voltage drop and ampacity questions, but those do not replace the special article requirements.
RV parks and mobile home parks
RV parks supply recreational vehicles at individual sites. The exam may ask about site supply equipment, receptacle configurations, feeder and service load calculations, grounding, disconnecting means, or pedestal location. RV park demand calculations are special because not every site is assumed to draw full rating at the same time. Use the demand rules in the RV park article rather than applying a dwelling service calculation.
Mobile home parks have related but distinct concerns. A mobile home is supplied by a feeder or service arrangement governed by the mobile home article and general service and feeder rules. Questions may involve the location of service equipment, the feeder to the home, grounding electrode connections, bonding, and disconnecting means. Do not treat a mobile home park exactly like a site-built dwelling subdivision unless the rule supports that result.
Case lab
Case 1: A hospital exam room receptacle circuit uses a wiring method that does not provide the required equipment grounding path for the patient care space. The circuit ampacity might be adequate, but the installation fails the patient safety requirement. Look at the patient care rule before box fill or device style.
Case 2: A marina owner wants standard weather-resistant receptacles on a dock pedestal. Weather resistance is only one piece. The pedestal must meet shore-power equipment rules, ground-fault protection, wet-location enclosure requirements, and bonding or grounding requirements.
Case 3: An RV park expansion adds 20 new sites. The service calculation should use the RV park article demand logic and equipment rules. A generic commercial load calculation can overstate or understate the code answer because it ignores the occupancy-specific method.
Exam traps
The most common trap is using a familiar residential or commercial rule after the stem has already named a special occupancy. Another trap is treating grounding and bonding as the same thing. Grounding connects to the earth and grounded system points; bonding connects metal parts so fault current can return and protective devices can operate. In healthcare and marinas, that distinction is not academic. It is the reason the special article exists.