Study guide
9.6 OSHA Subpart K and Safe Work Practice Context
Journeyman Electrician Study Guide Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Exam Orientation and Source Control
1.1 ICC R17, T17, G17, and Jurisdiction Variance 1.2 Current Format, Cost, Time, and Passing Score 1.3 Licensing Board vs. Exam Provider 1.4 Official References, Open-Book Rules, and Calculators 1.5 Domain Weights and Study Map 1.6 Using the Practice Bank, Error Log, and NEC Index
2 Chapter 2: NEC Navigation, Definitions, and Code Strategy
2.1 NEC Book Structure and Article Map 2.2 Article 100 Definitions and Exam Language 2.3 Index, Table, and Annex Navigation 2.4 Shall, Shall Not, Permitted, and Informational Notes 2.5 Using Code References Without Overlooking Context 2.6 State Amendments and Code Edition Control 2.7 NEC Navigation Case Lab
3 Chapter 3: Electrical Theory and Calculation Foundations
3.1 Ohm's Law, Power, and Basic Units 3.2 Series, Parallel, and Circuit Behavior 3.3 Single-Phase, Three-Phase, and Voltage Systems 3.4 Continuous Loads, Demand, and 125 Percent Rules 3.5 Voltage Drop and Practical Calculation Setup 3.6 Load Calculation Workflow 3.7 Calculation Foundation Case Lab
4 Chapter 4: Services, Service Equipment, and Grounding/Bonding
4.1 Service Point, Service Conductors, and Disconnects 4.2 Service Load Calculation and Sizing 4.3 Service Equipment, Panelboards, and Switchboards 4.4 Grounding Electrode System and GEC 4.5 Bonding, Main Bonding Jumpers, and Effective Fault Path 4.6 Transformers and Separately Derived Systems 4.7 Services and Grounding Case Lab
5 Chapter 5: Feeders, Branch Circuits, and Conductor Sizing
5.1 Feeder vs. Branch Circuit Boundaries 5.2 Branch Circuit Ratings and Required Outlets 5.3 Conductor Ampacity, Temperature, and Terminal Ratings 5.4 Adjustment, Correction, and More Than Three Conductors 5.5 Overcurrent Protection and Small-Conductor Rules 5.6 GFCI, AFCI, Equipment Grounding, and Dwelling Circuits 5.7 Feeders and Branch Circuits Case Lab
6 Chapter 6: Wiring Methods, Raceways, Boxes, and Cables
6.1 Raceway Selection and Installation Logic 6.2 Underground Wiring, Wet Locations, and Protection 6.3 Boxes, Enclosures, and Conduit Bodies 6.4 Box Fill, Conductor Counting, and Device Yokes 6.5 Cabinets, Panelboards, and Switchboards 6.6 Flexible Cords, Cables, and Temporary Wiring 6.7 Wiring Methods Case Lab
7 Chapter 7: Equipment, Devices, Luminaires, and Controls
7.1 Receptacles, Switches, and Device Selection 7.2 Luminaires, Lampholders, and Lighting Outlets 7.3 Appliances and Utilization Equipment 7.4 Heating, Cooling, and HVAC Electrical Connections 7.5 Disconnects, Controllers, and Switching Devices 7.6 Equipment Grounding, Bonding, and Listing Markings 7.7 Equipment and Devices Case Lab
8 Chapter 8: Motors, Generators, Transformers, and Special Equipment
8.1 Motor Circuit Anatomy and Article 430 Navigation 8.2 Motor Conductors, Overload, and Short-Circuit Protection 8.3 Motor Controllers, Disconnects, and Nameplates 8.4 Generators, Transfer Equipment, and Optional Standby 8.5 Transformer Sizing, Protection, and Grounding 8.6 Emergency Systems, Fire Alarms, and Signaling Overview 8.7 Motors and Generators Case Lab
9 Chapter 9: Special Occupancies, Renewables, and Safety
9.1 Hazardous Classified Locations 9.2 Healthcare, Marinas, RV Parks, and Mobile Home Parks 9.3 Pools, Spas, and Similar Installations 9.4 Solar PV, Energy Storage, and Renewable Systems 9.5 Temporary Power, Emergency Systems, and Special Conditions 9.6 OSHA Subpart K and Safe Work Practice Context 9.7 Special Occupancies Case Lab
10 Chapter 10: Open-Book Exam Workflow and Mixed Code Labs
10.1 Four-Hour Pacing and Question Triage 10.2 Look-Up vs. Know-From-Memory Decisions 10.3 Mixed Calculation Lab 10.4 Mixed Code Navigation Lab 10.5 Diagnostic Report and Error Log Remediation 10.6 High-Weight Domain Remediation Plan 10.7 Full Exam Simulation Playbook
11 Chapter 11: Final Review, Test Day, and License Planning
11.1 Final Two-Week Study Plan 11.2 Reference Book, Tabs, and Allowed Materials Checklist 11.3 Pearson VUE, PRONTO, and Test-Day Rules 11.4 After the Exam: Results, Retakes, and Challenges 11.5 License Application, Work Hours, and Jurisdiction Next Steps 11.6 After Journeyman: Master, Contractor, and Continuing Education
9.6 OSHA Subpart K and Safe Work Practice Context
Key Takeaways Explain This Topic AI
OSHA 1926 Subpart K is construction safety context for electrical work; it does not replace the NEC as the primary ICC journeyman installation reference.
Safe work practice questions often involve de-energizing, lockout or tagging, guarding, GFCI protection, damaged cords, working clearances, and qualified-person judgment.
Exam candidates should distinguish installation code requirements from employer safety obligations and jobsite procedures.
The safest field answer is not always the correct NEC lookup answer, so identify whether the question is asking code installation, OSHA context, or practical hazard recognition.
Last updated: May 2026
Safety context for a code exam
The journeyman electrician exam is code-centered, but electrical work is performed by people in real spaces. OSHA 1926 Subpart K covers construction electrical safety topics such as wiring design and protection, wiring methods, equipment for general use, specific purpose equipment and installations, hazardous classified locations, special systems, general requirements, and lockout or tagging. It is safety context for this guide, not a replacement for the NEC articles used in ICC R17, T17, and G17 exams.
Use this distinction:
Question type Primary reference habit Example issue
NEC installation rule Navigate the NEC article and tables Conductor ampacity, GFCI requirement, wiring method permission
OSHA construction safety context Recognize jobsite hazard control Damaged cords, guarding, lockout or tagging, temporary power safety
Manufacturer/listing instruction Follow listed equipment instructions Torque, terminal rating, battery system installation
Jurisdictional licensing Check state or local board License scope, renewal, continuing education
The source brief says ICC contractor/trades exams help licensing agencies evaluate candidates, but ICC is not a licensing agency. Passing an ICC exam does not automatically create a state license. That same source-control habit applies to safety: do not turn OSHA into an NEC substitute, and do not turn NEC installation rules into an employer safety program.
De-energizing and lockout context
Safe electrical work usually starts by establishing an electrically safe work condition when feasible. That means identifying all sources, interrupting load current properly, opening disconnects, applying lockout or tagging procedures, verifying absence of voltage with a properly rated tester, and controlling stored energy. Construction sites add temporary generators, backfeed sources, damaged cords, wet ground, and incomplete systems.
For an exam question, identify whether the stem asks what installation is code-compliant or what safety practice controls the hazard. If a worker is replacing a panelboard breaker, the NEC may tell you the breaker must be listed for the panel, sized for conductors, and installed in the proper enclosure. Safe work practice tells you the panel should be de-energized and locked or tagged according to procedure unless justified energized work rules apply. Both ideas matter, but they answer different questions.
GFCI, cords, and temporary power hazards
Subpart K safety context often overlaps with NEC temporary wiring. Construction receptacles, extension cords, portable tools, wet surfaces, and damaged insulation create shock hazards. GFCI protection is a common control. So is inspecting cords, removing damaged equipment from service, protecting wiring from physical damage, and keeping covers and guards in place.
A common trap is treating a cord as if it were a permanent wiring method. Flexible cords have permitted uses and prohibited uses. They cannot be run through holes, hidden in walls, used as a substitute for fixed wiring, or abused by doors and sharp edges in ordinary cases. On a jobsite, the hazard may also include trip exposure, strain, water, vehicle traffic, and temporary panels without proper covers.
Working clearances and guarding
Working space around electrical equipment is both a code and safety issue. The NEC provides installation requirements for access and working space. OSHA context reinforces that workers must be protected from contact with energized parts and from unsafe equipment conditions. A panel blocked by stored material can be an OSHA-style jobsite problem and can also violate access requirements.
Guarding includes covers, barriers, enclosures, elevation, locked rooms, or other means that keep unqualified persons away from live parts. Missing knockouts, open panel covers, exposed bus, damaged extension cords, and unguarded temporary lighting are not minor housekeeping matters. They create shock and burn hazards.
Qualified-person judgment
Many electrical tasks require qualified persons because the worker must understand construction, operation, hazards, and controls. A journeyman exam tests code knowledge, but the field expects judgment: identify all sources, read nameplates, verify ratings, choose meters correctly, use PPE when required by the employer safety program, and stop when the system does not match the drawings.
Do not overread this into licensing. States and local boards decide license scope, and the ICC bulletin says candidates should confirm requirements with the jurisdiction where they want to work. The exam does not give one national license.
Case lab
Case 1: A temporary panel on a construction site has missing covers and receptacles used outdoors without required protection. The NEC path includes temporary wiring and GFCI rules. OSHA context includes guarding, damaged equipment, and employer controls.
Case 2: A worker opens a disconnect marked off but does not verify absence of voltage. The safety issue is failure to confirm the equipment is de-energized. The code issue might still involve disconnect rating and labeling, but the immediate work-practice hazard is verification.
Case 3: A rooftop PV system is shut off at the AC breaker, but DC source conductors remain energized in sunlight. Safe practice requires source awareness and testing. NEC PV rules address disconnecting means, rapid shutdown, and marking. Both are needed for real work.
For exam prep, label each safety-flavored question as one of three things: installation rule, safety practice, or jurisdiction procedure. Then answer from the right source.