Study guide

6.4 Box Fill, Conductor Counting, and Device Yokes

Journeyman Electrician Study Guide Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Exam Orientation and Source Control

1.1 ICC R17, T17, G17, and Jurisdiction Variance 1.2 Current Format, Cost, Time, and Passing Score 1.3 Licensing Board vs. Exam Provider 1.4 Official References, Open-Book Rules, and Calculators 1.5 Domain Weights and Study Map 1.6 Using the Practice Bank, Error Log, and NEC Index

2 Chapter 2: NEC Navigation, Definitions, and Code Strategy

2.1 NEC Book Structure and Article Map 2.2 Article 100 Definitions and Exam Language 2.3 Index, Table, and Annex Navigation 2.4 Shall, Shall Not, Permitted, and Informational Notes 2.5 Using Code References Without Overlooking Context 2.6 State Amendments and Code Edition Control 2.7 NEC Navigation Case Lab

3 Chapter 3: Electrical Theory and Calculation Foundations

3.1 Ohm's Law, Power, and Basic Units 3.2 Series, Parallel, and Circuit Behavior 3.3 Single-Phase, Three-Phase, and Voltage Systems 3.4 Continuous Loads, Demand, and 125 Percent Rules 3.5 Voltage Drop and Practical Calculation Setup 3.6 Load Calculation Workflow 3.7 Calculation Foundation Case Lab

4 Chapter 4: Services, Service Equipment, and Grounding/Bonding

4.1 Service Point, Service Conductors, and Disconnects 4.2 Service Load Calculation and Sizing 4.3 Service Equipment, Panelboards, and Switchboards 4.4 Grounding Electrode System and GEC 4.5 Bonding, Main Bonding Jumpers, and Effective Fault Path 4.6 Transformers and Separately Derived Systems 4.7 Services and Grounding Case Lab

5 Chapter 5: Feeders, Branch Circuits, and Conductor Sizing

5.1 Feeder vs. Branch Circuit Boundaries 5.2 Branch Circuit Ratings and Required Outlets 5.3 Conductor Ampacity, Temperature, and Terminal Ratings 5.4 Adjustment, Correction, and More Than Three Conductors 5.5 Overcurrent Protection and Small-Conductor Rules 5.6 GFCI, AFCI, Equipment Grounding, and Dwelling Circuits 5.7 Feeders and Branch Circuits Case Lab

6 Chapter 6: Wiring Methods, Raceways, Boxes, and Cables

6.1 Raceway Selection and Installation Logic 6.2 Underground Wiring, Wet Locations, and Protection 6.3 Boxes, Enclosures, and Conduit Bodies 6.4 Box Fill, Conductor Counting, and Device Yokes 6.5 Cabinets, Panelboards, and Switchboards 6.6 Flexible Cords, Cables, and Temporary Wiring 6.7 Wiring Methods Case Lab

7 Chapter 7: Equipment, Devices, Luminaires, and Controls

7.1 Receptacles, Switches, and Device Selection 7.2 Luminaires, Lampholders, and Lighting Outlets 7.3 Appliances and Utilization Equipment 7.4 Heating, Cooling, and HVAC Electrical Connections 7.5 Disconnects, Controllers, and Switching Devices 7.6 Equipment Grounding, Bonding, and Listing Markings 7.7 Equipment and Devices Case Lab

8 Chapter 8: Motors, Generators, Transformers, and Special Equipment

8.1 Motor Circuit Anatomy and Article 430 Navigation 8.2 Motor Conductors, Overload, and Short-Circuit Protection 8.3 Motor Controllers, Disconnects, and Nameplates 8.4 Generators, Transfer Equipment, and Optional Standby 8.5 Transformer Sizing, Protection, and Grounding 8.6 Emergency Systems, Fire Alarms, and Signaling Overview 8.7 Motors and Generators Case Lab

9 Chapter 9: Special Occupancies, Renewables, and Safety

9.1 Hazardous Classified Locations 9.2 Healthcare, Marinas, RV Parks, and Mobile Home Parks 9.3 Pools, Spas, and Similar Installations 9.4 Solar PV, Energy Storage, and Renewable Systems 9.5 Temporary Power, Emergency Systems, and Special Conditions 9.6 OSHA Subpart K and Safe Work Practice Context 9.7 Special Occupancies Case Lab

10 Chapter 10: Open-Book Exam Workflow and Mixed Code Labs

10.1 Four-Hour Pacing and Question Triage 10.2 Look-Up vs. Know-From-Memory Decisions 10.3 Mixed Calculation Lab 10.4 Mixed Code Navigation Lab 10.5 Diagnostic Report and Error Log Remediation 10.6 High-Weight Domain Remediation Plan 10.7 Full Exam Simulation Playbook

11 Chapter 11: Final Review, Test Day, and License Planning

11.1 Final Two-Week Study Plan 11.2 Reference Book, Tabs, and Allowed Materials Checklist 11.3 Pearson VUE, PRONTO, and Test-Day Rules 11.4 After the Exam: Results, Retakes, and Challenges 11.5 License Application, Work Hours, and Jurisdiction Next Steps 11.6 After Journeyman: Master, Contractor, and Continuing Education

6.4 Box Fill, Conductor Counting, and Device Yokes

Key Takeaways Explain This Topic AI

Box fill is a volume calculation based on conductor equivalents, device yokes, internal clamps, support fittings, and equipment grounding conductors.

Each conductor that originates outside and terminates or is spliced in the box usually counts once, but pass-through and looped conductors have special treatment.

All equipment grounding conductors together normally count as one conductor volume of the largest grounding conductor present, with added rules for isolated grounds.

Device yokes count by the number and size of conductors connected to them, so switches and receptacles can change the required volume quickly.

Last updated: May 2026

Why box fill matters

Box fill protects insulation from damage, overheating from crowding, and poor workmanship caused by forcing too many conductors and devices into a small space. On the exam, box fill is attractive because a short stem can test several counting rules. The answer is rarely found by intuition. You need a consistent counting workflow.

Use this box-fill workflow:

Identify the box volume in cubic inches, or identify the box size and volume from the table.

List each conductor entering the box by size and function.

Count conductors that originate outside the box and terminate or are spliced in the box.

Apply pass-through and loop rules correctly.

Add internal clamp allowances where required.

Add equipment grounding conductor allowance.

Add device yoke allowances.

Add support fitting or luminaire stud allowances where required.

Convert conductor equivalents to cubic inches using the largest conductor size in each allowance group.

Compare required volume to available volume.

The exam may give a box marked 18 cubic inches and ask whether it can contain a duplex receptacle, two cables, grounds, and internal clamps. Do not start with the answer choices. Build the count.

Basic conductor counting

A conductor that originates outside the box and terminates or is spliced in the box generally counts once. A conductor that passes through the box without splice or termination may count differently depending on length and loop arrangement. A pigtail that originates and ends within the same box usually does not count as a separate conductor for box fill because it does not enter from outside. That pigtail can still matter for workmanship and device connection, but it is not counted the same way as a branch-circuit conductor entering the box.

Conductors of different sizes are counted by volume for their size. A box with 12 AWG and 14 AWG conductors is not solved by pretending all conductors are the smaller size. When an allowance is based on the largest conductor in a group, use the largest conductor involved in that allowance.

A useful table for scratch work:

  • Item in box Typical counting idea
  • Ungrounded conductor spliced or terminated Counts once by size
  • Neutral spliced or terminated Counts once by size
  • Pigtail wholly inside box Usually not counted
  • All equipment grounding conductors Count as one conductor volume of largest EGC, with exceptions to check
  • Internal cable clamp Count as one conductor volume based on largest conductor in box
  • Device yoke Counts as two conductor volumes based on connected conductor size in common cases
  • Fixture stud or hickey Count where rule requires
  • Equipment grounding conductors

All equipment grounding conductors in a box are often counted together as one conductor volume, using the largest equipment grounding conductor present. This is an exam favorite because a box may contain three bare grounds and one green pigtail, but the basic allowance is not four separate conductor volumes. However, isolated equipment grounding conductors and special configurations can change the analysis, so read the exact rule in the edition being tested.

Do not confuse grounding conductor counting with raceway fill. In raceway fill, equipment grounding conductors are conductors and generally occupy space. In box fill, the grounding conductor allowance is a special counting rule. The same physical wire is treated under different calculation systems for different purposes.

Device yokes

A device yoke or strap holds a switch, receptacle, or similar device. Box fill assigns volume to devices because they occupy space and crowd conductors. In a common single-gang receptacle example, the yoke counts as two conductor volumes based on the largest conductor connected to the device. If 12 AWG conductors are connected, use the 12 AWG volume for those two allowances.

Multiple devices multiply the issue. A two-gang box with two switches can require four conductor volumes for the two yokes, before counting the circuit conductors, grounds, clamps, and any support fittings. This is why replacing a simple switch with a bulky dimmer in a shallow old box can create a real code and workmanship problem.

Field/exam trap: a device yoke is not counted by the number of screws on the device. It is counted by the rule for devices mounted on the yoke and the conductors connected to them. Another trap is counting pigtails twice: once as part of the splice and again as a conductor entering the box. If the pigtail stays wholly inside the box, it is usually not counted as an entering conductor.

Worked example

Suppose a metal device box contains two 12 AWG NM cables. One cable brings power in and one carries power out. The ungrounded conductors are spliced with a pigtail to a receptacle, the neutrals are connected to the receptacle or spliced as required, all bare grounds are spliced with a grounding pigtail, the box has an internal clamp, and one duplex receptacle is mounted on a yoke.

A typical count would include two ungrounded conductors entering, two grounded conductors entering, one equipment grounding conductor allowance for all grounds, one internal clamp allowance if the clamp is inside the box, and two conductor volumes for the device yoke based on 12 AWG. The pigtails wholly inside the box do not add separate entering-conductor counts. If the required volume exceeds the box marking or table value, the installation needs a larger box or different arrangement.

Exam checklist

Before selecting an answer, ask: Did I count all entering current-carrying conductors? Did I avoid counting internal pigtails as entering conductors? Did I include the device yoke? Did I include internal clamps but not external clamps? Did I group equipment grounding conductors correctly? Did I use the cubic inch allowance for the correct conductor size? Most missed box-fill questions come from one skipped allowance, not from hard arithmetic.