Study guide

6.5 Cabinets, Panelboards, and Switchboards

Journeyman Electrician Study Guide Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Exam Orientation and Source Control

1.1 ICC R17, T17, G17, and Jurisdiction Variance 1.2 Current Format, Cost, Time, and Passing Score 1.3 Licensing Board vs. Exam Provider 1.4 Official References, Open-Book Rules, and Calculators 1.5 Domain Weights and Study Map 1.6 Using the Practice Bank, Error Log, and NEC Index

2 Chapter 2: NEC Navigation, Definitions, and Code Strategy

2.1 NEC Book Structure and Article Map 2.2 Article 100 Definitions and Exam Language 2.3 Index, Table, and Annex Navigation 2.4 Shall, Shall Not, Permitted, and Informational Notes 2.5 Using Code References Without Overlooking Context 2.6 State Amendments and Code Edition Control 2.7 NEC Navigation Case Lab

3 Chapter 3: Electrical Theory and Calculation Foundations

3.1 Ohm's Law, Power, and Basic Units 3.2 Series, Parallel, and Circuit Behavior 3.3 Single-Phase, Three-Phase, and Voltage Systems 3.4 Continuous Loads, Demand, and 125 Percent Rules 3.5 Voltage Drop and Practical Calculation Setup 3.6 Load Calculation Workflow 3.7 Calculation Foundation Case Lab

4 Chapter 4: Services, Service Equipment, and Grounding/Bonding

4.1 Service Point, Service Conductors, and Disconnects 4.2 Service Load Calculation and Sizing 4.3 Service Equipment, Panelboards, and Switchboards 4.4 Grounding Electrode System and GEC 4.5 Bonding, Main Bonding Jumpers, and Effective Fault Path 4.6 Transformers and Separately Derived Systems 4.7 Services and Grounding Case Lab

5 Chapter 5: Feeders, Branch Circuits, and Conductor Sizing

5.1 Feeder vs. Branch Circuit Boundaries 5.2 Branch Circuit Ratings and Required Outlets 5.3 Conductor Ampacity, Temperature, and Terminal Ratings 5.4 Adjustment, Correction, and More Than Three Conductors 5.5 Overcurrent Protection and Small-Conductor Rules 5.6 GFCI, AFCI, Equipment Grounding, and Dwelling Circuits 5.7 Feeders and Branch Circuits Case Lab

6 Chapter 6: Wiring Methods, Raceways, Boxes, and Cables

6.1 Raceway Selection and Installation Logic 6.2 Underground Wiring, Wet Locations, and Protection 6.3 Boxes, Enclosures, and Conduit Bodies 6.4 Box Fill, Conductor Counting, and Device Yokes 6.5 Cabinets, Panelboards, and Switchboards 6.6 Flexible Cords, Cables, and Temporary Wiring 6.7 Wiring Methods Case Lab

7 Chapter 7: Equipment, Devices, Luminaires, and Controls

7.1 Receptacles, Switches, and Device Selection 7.2 Luminaires, Lampholders, and Lighting Outlets 7.3 Appliances and Utilization Equipment 7.4 Heating, Cooling, and HVAC Electrical Connections 7.5 Disconnects, Controllers, and Switching Devices 7.6 Equipment Grounding, Bonding, and Listing Markings 7.7 Equipment and Devices Case Lab

8 Chapter 8: Motors, Generators, Transformers, and Special Equipment

8.1 Motor Circuit Anatomy and Article 430 Navigation 8.2 Motor Conductors, Overload, and Short-Circuit Protection 8.3 Motor Controllers, Disconnects, and Nameplates 8.4 Generators, Transfer Equipment, and Optional Standby 8.5 Transformer Sizing, Protection, and Grounding 8.6 Emergency Systems, Fire Alarms, and Signaling Overview 8.7 Motors and Generators Case Lab

9 Chapter 9: Special Occupancies, Renewables, and Safety

9.1 Hazardous Classified Locations 9.2 Healthcare, Marinas, RV Parks, and Mobile Home Parks 9.3 Pools, Spas, and Similar Installations 9.4 Solar PV, Energy Storage, and Renewable Systems 9.5 Temporary Power, Emergency Systems, and Special Conditions 9.6 OSHA Subpart K and Safe Work Practice Context 9.7 Special Occupancies Case Lab

10 Chapter 10: Open-Book Exam Workflow and Mixed Code Labs

10.1 Four-Hour Pacing and Question Triage 10.2 Look-Up vs. Know-From-Memory Decisions 10.3 Mixed Calculation Lab 10.4 Mixed Code Navigation Lab 10.5 Diagnostic Report and Error Log Remediation 10.6 High-Weight Domain Remediation Plan 10.7 Full Exam Simulation Playbook

11 Chapter 11: Final Review, Test Day, and License Planning

11.1 Final Two-Week Study Plan 11.2 Reference Book, Tabs, and Allowed Materials Checklist 11.3 Pearson VUE, PRONTO, and Test-Day Rules 11.4 After the Exam: Results, Retakes, and Challenges 11.5 License Application, Work Hours, and Jurisdiction Next Steps 11.6 After Journeyman: Master, Contractor, and Continuing Education

6.5 Cabinets, Panelboards, and Switchboards

Key Takeaways Explain This Topic AI

Cabinets and panelboards are governed by enclosure, working space, conductor bending space, termination, labeling, and overcurrent device rules.

Panelboards must be installed so circuits can be identified, unused openings are closed, and conductors are not damaged or crowded.

Neutral and equipment grounding conductor termination rules are a frequent trap, especially in downstream panels.

Switchboards, switchgear, and panelboards require attention to access, working clearance, dedicated space, and available fault-current context.

Last updated: May 2026

Cabinets and panelboards as wiring-method endpoints

A raceway or cable run often ends at a cabinet, panelboard, switchboard, or similar enclosure. The code question does not stop when the conductor reaches the cabinet. The enclosure must be suitable for the location, openings must be closed, conductors must be protected from abrasion, terminations must be listed for the conductor material and size, and working space must be maintained.

Use this navigation map:

  • Topic What to verify
  • Enclosure Dry, damp, wet, indoor, outdoor, corrosion, unused openings closed
  • Raceway entry Listed fittings, bushings where needed, bonding, conductor protection
  • Working space Depth, width, height, access, door swing where applicable
  • Dedicated space Clear area above or around equipment where required

Terminations Conductor material, temperature rating, torque, one conductor per terminal unless listed otherwise

  • Neutrals and grounds Bonding location, isolation in feeders, separate bars where required
  • Identification Circuit directory, disconnect labels, panel schedule accuracy

Exam stems often say panel, cabinet, or switchboard casually. Read whether the question is about a cabinet enclosure, the panelboard inside, or the distribution equipment assembly. A cabinet is an enclosure. A panelboard contains buses and overcurrent devices and is mounted in a cabinet or cutout box. A switchboard is generally a larger freestanding assembly. The practical rules overlap, but the code article path may change.

Working space and access

Electrical equipment likely to require examination, adjustment, servicing, or maintenance while energized needs working space. Panelboards and switchboards are common examples. The rule protects the worker, not just the equipment. Storage in front of a panel, a pipe crossing the required space, or a locked room without required access can become a violation.

Working space questions usually provide voltage to ground, condition of exposed live parts or grounded surfaces, and dimensions. Do not guess the depth. Use the working-space table for the tested NEC edition. Width and height rules are also tested. The required space is not a shelf, closet, or storage zone.

Dedicated equipment space is a different concept. It protects electrical equipment from foreign systems such as plumbing, ducts, or unrelated equipment occupying the zone reserved for electrical installation and future work. On the exam, wrong answers often confuse working clearance in front of equipment with dedicated space above equipment.

Conductors entering cabinets

Conductors entering a cabinet need protection from sharp edges and must be arranged so bending space is adequate. Large conductors require more bending space than small branch-circuit conductors. A panel can have enough ampacity and still fail because the conductors are bent too sharply at terminals.

Raceways entering service equipment may need bonding bushings or other bonding means depending on concentric or eccentric knockouts, service conductor raceways, and the wiring method. This is where Article 250, Article 300, and the equipment article meet. If the question mentions service raceway, reducing washers, concentric knockout, or bonding bushing, assume grounding and bonding are the issue.

Unused openings must be closed with fittings that maintain the protection of the enclosure. Tape over a knockout is not a code closure. Missing breaker blanks in a panelboard are also a common field defect because they leave openings in the dead front.

Neutral and grounding conductor traps

In service equipment, the grounded conductor is bonded to the service disconnect enclosure under the service bonding rules. Downstream feeder-supplied panelboards usually require isolated neutrals and separate equipment grounding bars, with equipment grounding conductors bonded to the enclosure. The exam frequently tests the difference.

Do not land two neutrals under one terminal unless the equipment is specifically listed for it, and most panelboard neutral bars are not listed for multiple grounded conductors under one screw. Equipment grounding conductors may have different terminal allowances if listed, but never assume. Read the equipment marking and listing logic.

A common case: a detached garage feeder has a panel with the neutral bar bonded to the cabinet and no separate equipment grounding conductor. Depending on code edition and conditions, that may be a trap. Modern exam logic generally expects a feeder equipment grounding conductor and neutral isolation in the downstream panel, unless a specific exception from the applicable edition applies.

Circuit directories and identification

Panelboard circuits must be identified in a way that is clear, specific, and durable enough for the installation. A directory marked lights and plugs for every breaker is weak. The exam may ask whether spare, kitchen receptacles, HVAC, bathroom, or office circuits are properly identified. Accurate directories matter for safe maintenance and emergency response.

Disconnects and service equipment also have marking requirements. Available fault current, service disconnect identification, and source identification can appear in other chapters, but panelboard questions often reference them. Do not treat labels as paperwork outside the NEC; identification can be a code requirement.

Installation case

Case 1: An EMT feeder enters a metal panelboard cabinet through concentric knockouts. The question asks about grounding continuity. Check whether the raceway is service or feeder, whether bonding around the knockout is reliable, and whether a bonding bushing or jumper is required.

Case 2: A commercial panel has open breaker spaces without blanks. The issue is not load calculation. The dead front must close openings so live parts are not exposed.

Case 3: A feeder panel in an office suite has neutrals and equipment grounds on the same bonded bar. The likely exam issue is neutral isolation in a panel that is not service equipment.

Study habit

When you see a panelboard question, scan the stem for one of these signals: working space, dedicated space, wet location, unused opening, neutral bar, grounding bar, bonding screw, two neutrals one terminal, conductor bending, circuit directory, service equipment, or feeder panel. That signal tells you where to navigate before arithmetic starts.