Study guide
6.7 Wiring Methods Case Lab
Journeyman Electrician Study Guide Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Exam Orientation and Source Control
1.1 ICC R17, T17, G17, and Jurisdiction Variance 1.2 Current Format, Cost, Time, and Passing Score 1.3 Licensing Board vs. Exam Provider 1.4 Official References, Open-Book Rules, and Calculators 1.5 Domain Weights and Study Map 1.6 Using the Practice Bank, Error Log, and NEC Index
2 Chapter 2: NEC Navigation, Definitions, and Code Strategy
2.1 NEC Book Structure and Article Map 2.2 Article 100 Definitions and Exam Language 2.3 Index, Table, and Annex Navigation 2.4 Shall, Shall Not, Permitted, and Informational Notes 2.5 Using Code References Without Overlooking Context 2.6 State Amendments and Code Edition Control 2.7 NEC Navigation Case Lab
3 Chapter 3: Electrical Theory and Calculation Foundations
3.1 Ohm's Law, Power, and Basic Units 3.2 Series, Parallel, and Circuit Behavior 3.3 Single-Phase, Three-Phase, and Voltage Systems 3.4 Continuous Loads, Demand, and 125 Percent Rules 3.5 Voltage Drop and Practical Calculation Setup 3.6 Load Calculation Workflow 3.7 Calculation Foundation Case Lab
4 Chapter 4: Services, Service Equipment, and Grounding/Bonding
4.1 Service Point, Service Conductors, and Disconnects 4.2 Service Load Calculation and Sizing 4.3 Service Equipment, Panelboards, and Switchboards 4.4 Grounding Electrode System and GEC 4.5 Bonding, Main Bonding Jumpers, and Effective Fault Path 4.6 Transformers and Separately Derived Systems 4.7 Services and Grounding Case Lab
5 Chapter 5: Feeders, Branch Circuits, and Conductor Sizing
5.1 Feeder vs. Branch Circuit Boundaries 5.2 Branch Circuit Ratings and Required Outlets 5.3 Conductor Ampacity, Temperature, and Terminal Ratings 5.4 Adjustment, Correction, and More Than Three Conductors 5.5 Overcurrent Protection and Small-Conductor Rules 5.6 GFCI, AFCI, Equipment Grounding, and Dwelling Circuits 5.7 Feeders and Branch Circuits Case Lab
6 Chapter 6: Wiring Methods, Raceways, Boxes, and Cables
6.1 Raceway Selection and Installation Logic 6.2 Underground Wiring, Wet Locations, and Protection 6.3 Boxes, Enclosures, and Conduit Bodies 6.4 Box Fill, Conductor Counting, and Device Yokes 6.5 Cabinets, Panelboards, and Switchboards 6.6 Flexible Cords, Cables, and Temporary Wiring 6.7 Wiring Methods Case Lab
7 Chapter 7: Equipment, Devices, Luminaires, and Controls
7.1 Receptacles, Switches, and Device Selection 7.2 Luminaires, Lampholders, and Lighting Outlets 7.3 Appliances and Utilization Equipment 7.4 Heating, Cooling, and HVAC Electrical Connections 7.5 Disconnects, Controllers, and Switching Devices 7.6 Equipment Grounding, Bonding, and Listing Markings 7.7 Equipment and Devices Case Lab
8 Chapter 8: Motors, Generators, Transformers, and Special Equipment
8.1 Motor Circuit Anatomy and Article 430 Navigation 8.2 Motor Conductors, Overload, and Short-Circuit Protection 8.3 Motor Controllers, Disconnects, and Nameplates 8.4 Generators, Transfer Equipment, and Optional Standby 8.5 Transformer Sizing, Protection, and Grounding 8.6 Emergency Systems, Fire Alarms, and Signaling Overview 8.7 Motors and Generators Case Lab
9 Chapter 9: Special Occupancies, Renewables, and Safety
9.1 Hazardous Classified Locations 9.2 Healthcare, Marinas, RV Parks, and Mobile Home Parks 9.3 Pools, Spas, and Similar Installations 9.4 Solar PV, Energy Storage, and Renewable Systems 9.5 Temporary Power, Emergency Systems, and Special Conditions 9.6 OSHA Subpart K and Safe Work Practice Context 9.7 Special Occupancies Case Lab
10 Chapter 10: Open-Book Exam Workflow and Mixed Code Labs
10.1 Four-Hour Pacing and Question Triage 10.2 Look-Up vs. Know-From-Memory Decisions 10.3 Mixed Calculation Lab 10.4 Mixed Code Navigation Lab 10.5 Diagnostic Report and Error Log Remediation 10.6 High-Weight Domain Remediation Plan 10.7 Full Exam Simulation Playbook
11 Chapter 11: Final Review, Test Day, and License Planning
11.1 Final Two-Week Study Plan 11.2 Reference Book, Tabs, and Allowed Materials Checklist 11.3 Pearson VUE, PRONTO, and Test-Day Rules 11.4 After the Exam: Results, Retakes, and Challenges 11.5 License Application, Work Hours, and Jurisdiction Next Steps 11.6 After Journeyman: Master, Contractor, and Continuing Education
6.7 Wiring Methods Case Lab
Key Takeaways Explain This Topic AI
Mixed wiring-method cases should be sorted by location, method permission, conductor suitability, box rules, grounding, and protection before choosing an answer.
The most common traps are solving the calculation while missing a prohibited use or unsuitable location rating.
Box fill, raceway fill, pull-box sizing, and conductor ampacity are different calculations with different tables and triggers.
A field-ready answer explains both what is wrong and which compliant correction matches the failed rule.
Last updated: May 2026
How to attack mixed cases
Wiring-method questions rarely announce themselves as one topic. A stem may describe PVC underground to a garage, an LB on the outside wall, a feeder panel inside, a receptacle box, and an extension cord used for equipment. The candidate must sort the facts before looking for a table.
Use this case-lab checklist:
- Order Diagnostic question If yes, navigate to
- 1 Is any method prohibited in the location? Wiring method article and Article 300
2 Is the location wet, underground, corrosive, or subject to physical damage? Article 300, conductor rules, method article
- 3 Are splices, devices, or conductors in a box? Article 314 box rules
- 4 Is the question about cubic inches? Box fill
- 5 Is the question about raceway cross-sectional area? Chapter 9 raceway fill
- 6 Is the question about large raceways entering a box? Pull-box sizing
- 7 Is a panel, cabinet, or service enclosure involved? Working space, bonding, terminations, identification
- 8 Is a flexible cord or temporary setup involved? Flexible cord and temporary wiring rules
The first job is classification. Do not let a number in the stem lure you into the wrong calculation. Cubic inches means box fill. Raceway trade size and conductor count means raceway fill. Large raceways entering a pull box means pull-box sizing. Load current and conductor ampacity mean ampacity. Those are separate tools.
Case 1: Detached garage feeder
A homeowner wants a 60 amp feeder to a detached garage. The route leaves the house in PVC, runs underground across the yard, rises on the garage wall, enters an LB, then terminates in a panelboard. The stem says individual THHN conductors are pulled through the underground PVC.
Start with the wet-location issue. Underground raceway is wet inside, so conductors must be suitable for wet locations. If the conductor marking is only dry-location THHN in the fact pattern, the installation is suspect. Many modern conductors are dual marked, but the exam will usually state enough to decide. Next check burial cover, raceway type, physical protection at risers, expansion if relevant, and fittings at the LB.
At the garage panel, ask whether this is service equipment or a feeder panel. A feeder panel generally needs an equipment grounding conductor and isolated neutral bar, with grounding conductors bonded to the cabinet. If the answer choice bonds the neutral to the cabinet just because it is the first panel in the garage, be cautious. Detached-building rules can be nuanced by edition, but modern exam logic strongly tests neutral isolation for feeder panels.
Case 2: Tenant improvement with crowded boxes
A commercial remodel adds receptacles using EMT and metal boxes. One device box has two 12 AWG circuits, two neutrals, two equipment grounding conductors, an internal clamp, and one duplex receptacle. The question asks whether an 18 cubic inch box is adequate.
This is not raceway fill. It is box fill. Count entering conductors that terminate or splice, count the equipment grounding conductor allowance, count internal clamps if present, count the device yoke, and convert the allowances using the correct cubic inch volume for 12 AWG. If the required volume is greater than 18 cubic inches, the fix is a larger box, extension ring where permitted, or revised layout. Do not solve by increasing breaker size or changing the receptacle rating.
Field trap: if the box is metal and EMT is used as the grounding path, the box still needs bonding continuity. Device grounding, box bonding, and equipment grounding path rules may still apply. A fill calculation does not excuse a loose locknut or missing bonding jumper where required.
Case 3: Rooftop HVAC connection
A rooftop unit is supplied by conductors in EMT across part of the roof, transitions to liquidtight flexible metal conduit at the equipment, and terminates in a disconnect. The stem mentions sunlight, rain, vibration, and a long straight run exposed to temperature change.
Sort the issues. Rooftop means wet location and sunlight exposure. Conductors must be wet-location rated, and raceway or cable jackets must suit sunlight where applicable. Vibration near the equipment can justify flexible raceway, but the flexible raceway must be suitable for wet location and installed with listed fittings. If the raceway run is long and subject to expansion, expansion fittings or movement accommodation may be needed depending on the raceway material and conditions.
The disconnect and equipment working space are separate issues. Do not choose an answer that fixes the flexible raceway but blocks working clearance. In the field, several code rules apply at once; on the exam, the stem often asks which violation is present or which correction is required.
Case 4: Temporary event wiring
A temporary outdoor event uses cords to supply booths. Some cords are rated for hard usage and outdoor wet locations, supported off walkways, protected by GFCI devices, and removed after the event. Another cord is routed through a doorway, pinched by the door, and covered by a rug to prevent tripping.
The first setup may be acceptable if all temporary wiring rules and listing instructions are met. The second setup has physical damage and concealment problems. Covering a cord with a rug does not make it safer for code purposes; it can hide damage and heat. A small load does not legalize a damaged or improperly routed cord.
Case 5: Large feeder pull box
A feeder uses several large raceways entering a junction box. The question gives trade sizes and says one raceway enters the left side while another exits the top. This points to angle-pull sizing, not small-box fill. Use the pull-box rule for the applicable pull type and raceway arrangement. If the conductors are 4 AWG or larger, expect pull-box sizing to matter.
Wrong answers often use conductor ampacity tables or box cubic-inch tables. The numbers may look familiar, but the trigger is raceway arrangement. Train yourself to label the calculation before touching the table.
Final exam traps
Trap 1: Treating damp and wet as casual language. They are location classifications with product and installation consequences.
Trap 2: Assuming all conduit is equivalent. Each method has permitted uses, not permitted uses, support, bend, fitting, and grounding details.
Trap 3: Counting every ground separately in box fill. The rule is more specific.
Trap 4: Using flexible cord because it is easy. Cord rules are use-limited.
Trap 5: Forgetting access. Boxes and conduit bodies with splices or pull access must remain reachable.
A strong journeyman answer is not just code memory. It is a disciplined path through the book. Identify the wiring method, classify the location, choose the rule family, perform the calculation if there is one, and check whether the field correction actually fixes the failed condition.