Study guide
1.3 Material Standards & Piping Joining Methods
Journeyman Plumber Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Administration, Code Enforcement, & Safety
1.1 Administration, Permits, and Inspections 1.2 General Regulations & Building Integrity 1.3 Material Standards & Piping Joining Methods 1.4 Plumbing Math & Water Calculations 1.5 Isometric Drawings & Blueprint Reading
2 Chapter 2: Plumbing Fixtures, Appliances, & Water Heaters
Plumbing Fixtures & Minimum Standards Water Heaters & Safety Devices Special Fixtures & Healthcare Plumbing Fixture Installation & Connection Rules Water Conservation & Flow Rates
3 Chapter 3: Water Supply & Distribution Systems
Water Service Piping & Main Sizing Water Supply Sizing & WSFU Calculations Backflow Prevention & Cross-Connection Control Water Pressure Boosters & Reducing Valves Hot Water Distribution & Recirculation Disinfection & Potable Water Quality
4 Chapter 4: Sanitary Drainage Systems & DFU Sizing
4.1 Sanitary Drainage Fundamentals & DFU 4.2 Drainage Pipe Sizing & Minimum Slopes 4.3 Building Drains, Sewers, & Cleanouts 4.4 Sumps, Ejectors, & Sewage Pumps 4.5 Special Wastes & Chemical Drainage 4.6 Indirect & Special Waste Piping
5 Chapter 5: Plumbing Venting Systems
5.1 Venting Principles & Vent Stack Sizing 5.2 Individual, Common, & Wet Venting 5.3 Circuit, Loop, & Island Venting 5.4 Air Admittance Valves & Combination Vents 5.5 Vent Terminals & Roof Penetrations
6 Chapter 6: Traps, Interceptors, & Separators
6.1 Trap Requirements & Hydraulic Seals 6.2 Trap Seal Protection & Primers 6.3 Grease Interceptors & Hydromechanical Traps 6.4 Oil, Sand, & Flammable Liquid Separators 6.5 Backwater Valves & Flood Protection
7 Chapter 7: Storm Drainage & Exterior Systems
7.1 Storm Drainage Sizing & Roof Drains 7.2 Subsoil Drainage & Sump Systems 7.3 Combined & Separated Sewer Connections 7.4 Rainwater Harvesting & Non-Potable Systems
8 Chapter 8: Fuel Gas Piping & Appliance Venting
8.1 Fuel Gas Piping Materials & Joints 8.2 Fuel Gas Pipe Sizing & Pressure Drop 8.3 Gas Pipe Inspection, Testing, & Purging 8.4 Appliance Venting & Draft Hoods 8.5 Combustion Air & Appliance Location
1.3 Material Standards & Piping Joining Methods
Key Takeaways Explain This Topic AI
Type K copper has the thickest wall (green band) for underground water service; Type L is medium wall (blue band); Type M is thin wall (red band).
Lead-free solder containing no more than 0.2% lead is legally mandated for potable water systems, with soldering occurring below 840°F (450°C) and brazing above 840°F.
CPVC pipe is rated for hot water up to 180°F at 100 psi (ASTM D2846), whereas standard PVC is restricted to cold water and DWV applications up to 140°F max.
No-hub cast iron couplings require tightening stainless steel band clamps to a specified torque (typically 60 in-lbs for standard or 80 in-lbs for heavy duty).
Saddle valves and saddle tees are strictly prohibited by code on all potable water supply and DWV piping systems.
Last updated: August 2026
- Material Standards & Piping Joining Methods
- 1. Metallic Piping Materials and Industry Standards
Selecting the correct piping material requires understanding ASTM (American Society for Testing and Materials) manufacturing standards, wall thicknesses, operating pressure limits, and chemical compatibility.
Copper Tubing Standards
Copper pipe is classified into four standard wall thickness types, identified by color-coded surface printing: ┌─────────────────────────────────────────────────────────────────────────────┐
- │ COPPER TUBING TYPES & WALL THICKNESS │
- │ Type K [GREEN] ──► Extra Heavy Wall (Underground Water Service) │
- │ Type L [BLUE] ──► Medium Wall (Interior Water Supply & Heating) │
- │ Type M [RED] ──► Light Wall (Residential Interior Water Lines Aboveground)│
- │ DWV [YELLOW]──► Thin Wall (Unpressurized Drainage, Waste, & Vent Only) │
- └─────────────────────────────────────────────────────────────────────────────┘
Type K (Green Printing): Thickest wall dimension. Approved for underground water services, commercial distribution, high-pressure lines, and fuel gas piping. Available in hard temper (20-ft straight lengths) and soft temper (coil lengths).
Type L (Blue Printing): Medium wall thickness. The standard specification for commercial and residential interior water supply, hydronic heating, and domestic hot water lines.
Type M (Red Printing): Thin wall thickness. Permitted only for aboveground residential interior potable water supply lines and heating loops. Not permitted for underground service lines.
DWV Copper (Yellow Printing): Extra-thin wall. Designed strictly for unpressurized drain, waste, and vent applications. Cannot be used for pressurized water supply.
Cast Iron Soil Pipe (ASTM A74 / ASTM A888)
Cast iron is manufactured in two primary configurations for sanitary DWV systems:
Hub and Spigot (Service Weight / Extra Heavy): Features a bell/hub at one end into which the plain spigot end of the adjacent pipe fits. Joined using compression rubber gaskets or poured lead and oakum joints.
Hubless (No-Hub): Plain-end pipe joined using stainless steel shield couplings with internal elastomeric (neoprene) sleeves.
2. Plastic Piping Materials and Temperature Limits
Plastic piping systems must meet rigorous ASTM standards and carry the NSF-pw (National Sanitation Foundation - Potable Water) mark for potable water or NSF-dwv for drainage systems.
Material ASTM Standard Max Operating Temperature Primary Application Key Properties
PVC ASTM D1785 / D2665 140°F (60°C) Cold water supply, building sewer, DWV Rigid, low cost, requires primer + cement
CPVC ASTM D2846 / F441 180°F (82°C) at 100 psi Hot & cold potable water distribution High temperature chemical resistance
PEX ASTM F876 / F877 200°F (93°C) at 80 psi Hot & cold water, radiant floor heating Flexible, freeze-resistant, expansion memory
- ABS ASTM D2661 180°F (82°C) (unpressurized) Residential DWV drainage Rigid black plastic, no primer required
- 3. Joining Methods and Installation Techniques
Executing proper joints is essential for system longevity and leak prevention.
Solvent Weld Joints (PVC, CPVC, ABS)
Solvent welding is a chemical fusion process, not a glue bond. The solvent softens the plastic molecules, causing them to interlock when joined:
Cut & Deburr: Cut pipe square. Chamfer/bevel the outer edge to prevent scraping cement off fitting socket.
Primer Application (PVC): Apply purple primer (ASTM F656) to fitting socket and pipe end to chemically clean and soften plastic. Note: ABS does not require primer.
Cement Application: Apply a thin layer of solvent cement ( ASTM D2564 for PVC, ASTM F493 for CPVC, ASTM D2235 for ABS) to fitting socket and a heavy layer to pipe end. ASTM D2846 is the CPVC pipe and fitting system standard, not the cement standard — exams use that pair as a distractor.
Assembly: Immediately insert pipe into socket with a 1/4-turn twist until seated against socket shoulder.
Hold Time: Hold joint firmly together for 30 seconds to prevent pipe taper push-out. Allow proper cure time based on ambient temperature before pressure testing.
Soldering and Brazing Copper
The fundamental distinction between soldering and brazing lies in the melting temperature of the filler metal:
Soldering (Soft Soldering): Joining process using filler metal with a melting temperature below 840°F (450°C) (typically 400°F to 500°F).
Safe Drinking Water Act mandates lead-free solder (containing not more than 0.2% lead ) for potable water lines.
Water-soluble flux (ASTM B813) must be applied to cleaned pipe and fitting surfaces to prevent oxidation during heating. Capillary action draws melted solder into the joint gap (0.002 to 0.006 inch clearance).
Brazing (Hard Soldering): Joining process using filler metal with a melting temperature above 840°F (450°C) (typically 1,100°F to 1,500°F).
Uses silver-copper-phosphorus alloys (BCuP series). Flux is optional when joining copper-to-copper, but required for brass fittings. Mandatory for medical gas systems and underground copper lines.
Press-Connect Fittings (ProPress / Viega)
Press fittings utilize an internal EPDM (or NBR/FKM) O-ring. A calibrated hydraulic press tool crimps the fitting socket onto the copper or stainless steel tube, creating a permanent mechanical seal and structural joint without open flames.
Mechanical No-Hub Cast Iron Couplings
No-hub cast iron pipe is joined using a neoprene gasket surrounded by a corrugated stainless steel shield and band clamps:
Standard Couplings (2-band): Clamps must be torqued using a calibrated torque wrench to 60 inch-pounds .
Heavy-Duty Couplings (4-band or 6-band): Clamps must be torqued to 80 inch-pounds in a criss-cross sequence.
4. Prohibited Joints and Code Violations
Model plumbing codes explicitly prohibit certain pipe joining practices due to failure risk or sanitary hazards:
Saddle Valves and Saddle Tees: Strictly prohibited on all water distribution piping and DWV systems because they puncture pipe walls, restrict flow, and create corrosion points.
Dissimilar Plastic Cementing: Using PVC solvent cement to join ABS pipe to PVC pipe is prohibited (except when using special approved transition cement for single building sewer connections under UPC rules).
Solvent Cement on Underground Gas Lines: Plastic gas lines must be joined by heat fusion, not solvent welding.
Running Threads: Threaded connections using continuous running threads are prohibited on pressure lines.