Study guide
5.4 Air Admittance Valves & Combination Vents
Journeyman Plumber Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Administration, Code Enforcement, & Safety
1.1 Administration, Permits, and Inspections 1.2 General Regulations & Building Integrity 1.3 Material Standards & Piping Joining Methods 1.4 Plumbing Math & Water Calculations 1.5 Isometric Drawings & Blueprint Reading
2 Chapter 2: Plumbing Fixtures, Appliances, & Water Heaters
Plumbing Fixtures & Minimum Standards Water Heaters & Safety Devices Special Fixtures & Healthcare Plumbing Fixture Installation & Connection Rules Water Conservation & Flow Rates
3 Chapter 3: Water Supply & Distribution Systems
Water Service Piping & Main Sizing Water Supply Sizing & WSFU Calculations Backflow Prevention & Cross-Connection Control Water Pressure Boosters & Reducing Valves Hot Water Distribution & Recirculation Disinfection & Potable Water Quality
4 Chapter 4: Sanitary Drainage Systems & DFU Sizing
4.1 Sanitary Drainage Fundamentals & DFU 4.2 Drainage Pipe Sizing & Minimum Slopes 4.3 Building Drains, Sewers, & Cleanouts 4.4 Sumps, Ejectors, & Sewage Pumps 4.5 Special Wastes & Chemical Drainage 4.6 Indirect & Special Waste Piping
5 Chapter 5: Plumbing Venting Systems
5.1 Venting Principles & Vent Stack Sizing 5.2 Individual, Common, & Wet Venting 5.3 Circuit, Loop, & Island Venting 5.4 Air Admittance Valves & Combination Vents 5.5 Vent Terminals & Roof Penetrations
6 Chapter 6: Traps, Interceptors, & Separators
6.1 Trap Requirements & Hydraulic Seals 6.2 Trap Seal Protection & Primers 6.3 Grease Interceptors & Hydromechanical Traps 6.4 Oil, Sand, & Flammable Liquid Separators 6.5 Backwater Valves & Flood Protection
7 Chapter 7: Storm Drainage & Exterior Systems
7.1 Storm Drainage Sizing & Roof Drains 7.2 Subsoil Drainage & Sump Systems 7.3 Combined & Separated Sewer Connections 7.4 Rainwater Harvesting & Non-Potable Systems
8 Chapter 8: Fuel Gas Piping & Appliance Venting
8.1 Fuel Gas Piping Materials & Joints 8.2 Fuel Gas Pipe Sizing & Pressure Drop 8.3 Gas Pipe Inspection, Testing, & Purging 8.4 Appliance Venting & Draft Hoods 8.5 Combustion Air & Appliance Location
5.4 Air Admittance Valves & Combination Vents
Key Takeaways Explain This Topic AI
Air Admittance Valves (AAVs) are mechanical one-way valves complying with ASSE 1051 (individual/branch) or ASSE 1050 (stack) standards.
AAVs open under negative pressure (-0.01 psi / -0.25 inches w.c.) to admit air and seal by gravity under zero or positive pressure to trap sewer gases.
AAVs must be installed vertically within 15 degrees of plumb, at least 4 inches above the horizontal branch drain and 6 inches above stack insulation.
Combination Waste and Vent (CWV) systems are engineered horizontal drainage networks where the top half of an oversized pipe acts as a vent.
CWV systems are restricted to floor drains, sinks, and lavatories, requiring pipes to be oversized by 2 sizes (min 2" for sinks, 3" for floor drains).
Last updated: August 2026
- Air Admittance Valves & Combination Vents
- 1. Air Admittance Valves (AAVs): Standards and Operation
An Air Admittance Valve (AAV) is a one-way mechanical venting device designed to admit air into a sanitary drainage system when negative pressures develop, while preventing sewer gases from escaping into the building interior.
Governing Standards
AAVs must be tested and certified in accordance with national manufacturing standards:
ASSE 1051: Standard for Individual and Branch Type Air Admittance Valves for Sanitary Drainage Systems (used for individual fixtures and branch lines).
ASSE 1050: Standard for Stack Type Air Admittance Valves for Sanitary Drainage Systems (used at the top of vent stacks or stack vents).
- Operational Physics STATIC / POSITIVE PRESSURE NEGATIVE PRESSURE (-0.01 PSI)
- (Valve Sealed by Gravity) (Air Inrush Balances System)
- ┌───────┐ ┌─── ───┐ ▲ Air Entry
- │ Seal │ │ Seal │ │
- ═════╧═══════╧═════ ═════╪═══════╪═════
- Sewer Gas Blocked Ambient Air Admitted
Neutral / Positive Pressure State: Under static conditions or positive pressure events, the elastomeric sealing membrane rests firmly against its valve seat by gravity. Sewer gases, moisture, and odors are completely trapped inside the piping.
Negative Pressure State: When a fixture discharges, falling wastewater creates a partial vacuum. When negative pressure reaches -0.01 psi (-0.25 inches of water column or -62 Pa) , atmospheric pressure pushes the membrane off its seat, allowing room air to enter the branch drain and balance system pressure.
Resealing State: Once pneumatic equilibrium is restored, the valve drops closed by gravity, maintaining a gastight seal.
2. AAV Installation Rules, Accessibility, & Clearances
While AAVs reduce roof penetrations, model codes restrict their placement under IPC Section 918 and UPC Section 917 .
Elevation Clearances
Horizontal Branch AAVs: Must be located at least 4 inches (102 mm) above the top of the horizontal branch drain or fixture drain being served.
Stack AAVs: Must be located at least 6 inches (152 mm) above the flood level rim of the highest fixture connected to the stack, and at least 6 inches above any ceiling insulation in attic spaces.
Plumb Tolerance: Must be installed vertically within 15 degrees of true plumb.
Location and Accessibility Mandates
Accessible Location: AAVs must be installed in an accessible location that permits inspection, maintenance, and replacement. Acceptable locations include under-sink cabinets, wall cavities with louvered access panels, or ventilated attic spaces.
Free Air Circulation: The valve must be located in a space that receives continuous air movement. Installing an AAV in a sealed, airtight wall cavity or unventilated box is a code violation.
Prohibited Spaces: AAVs shall NOT be installed outdoors in cold climates where freezing occurs, in chemical waste systems, or inside return air plenums (unless specifically listed for plenum installation).
Outdoor Main Vent Mandate: AAVs cannot completely replace outdoor vents. Every building plumbing system MUST have at least one open vent terminal extending to the outdoor air (minimum 3 inches in diameter) to relieve positive sewer pressures.
3. Combination Waste and Vent (CWV) Systems
A Combination Waste and Vent (CWV) system is an engineered horizontal drainage layout in which a single oversized horizontal pipe functions simultaneously as a waste drain and as a vent.
Principles of Operation
In a standard DWV pipe, waste fills a significant portion of the pipe cross-section, requiring a separate dry vent to deliver air. In a CWV system, the pipe diameter is deliberately oversized so that liquid waste flows along the invert (bottom half), leaving the top half of the pipe open for free air circulation above the flow line. ┌─────────────────────────────────────────┐
- │ AIR CIRCULATION ZONE (Upper Half) │ ◄── Acts as Vent
- ├─────────────────────────────────────────┤
- │ LIQUID WASTE FLOW ZONE (Lower Half) │ ◄── Acts as Waste Drain
- └─────────────────────────────────────────┘
- Permitted vs. Prohibited Fixtures (IPC Section 915 / UPC Section 910)
PERMITTED Fixtures: Floor drains, floor sinks, drinking fountains, lavatories, and commercial sinks.
PROHIBITED Fixtures: CWV systems are strictly PROHIBITED from receiving discharge from water closets, bidets, or any fixture receiving solid fecal matter or heavy grease . Solid materials cause surging that fills the entire pipe cross-section, destroying the air passageway.
4. CWV Sizing Rules, Slope Limits, & Relief Venting
Because air and water share a single pipe in CWV systems, strict dimensional rules apply:
Pipe Oversizing Mandate
Horizontal drainage lines in a CWV system must be oversized by a minimum of 2 pipe sizes larger than required by standard DFU fixture tables:
Minimum size for lavatories/sinks in CWV: 2 inches (standard is 1-1/2").
Minimum size for floor drains/floor sinks in CWV: 3 inches (standard is 2").
Slope and Connection Rules
Maximum Slope: The maximum allowable slope for a horizontal CWV line is 1/2 inch per foot (4% slope) . Steeper slopes cause liquid velocity to increase, generating hydraulic waves that block air passage.
Minimum Slope: Standard 1/4 inch per foot (2%) slope.
Relief Vent Connection: Every CWV branch must be provided with a vertical relief vent at the upstream end (head) of the system or at its junction with the main drain to ensure continuous atmospheric air entry.