Study guide

7.4 Rainwater Harvesting & Non-Potable Systems

Journeyman Plumber Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Administration, Code Enforcement, & Safety

1.1 Administration, Permits, and Inspections 1.2 General Regulations & Building Integrity 1.3 Material Standards & Piping Joining Methods 1.4 Plumbing Math & Water Calculations 1.5 Isometric Drawings & Blueprint Reading

2 Chapter 2: Plumbing Fixtures, Appliances, & Water Heaters

Plumbing Fixtures & Minimum Standards Water Heaters & Safety Devices Special Fixtures & Healthcare Plumbing Fixture Installation & Connection Rules Water Conservation & Flow Rates

3 Chapter 3: Water Supply & Distribution Systems

Water Service Piping & Main Sizing Water Supply Sizing & WSFU Calculations Backflow Prevention & Cross-Connection Control Water Pressure Boosters & Reducing Valves Hot Water Distribution & Recirculation Disinfection & Potable Water Quality

4 Chapter 4: Sanitary Drainage Systems & DFU Sizing

4.1 Sanitary Drainage Fundamentals & DFU 4.2 Drainage Pipe Sizing & Minimum Slopes 4.3 Building Drains, Sewers, & Cleanouts 4.4 Sumps, Ejectors, & Sewage Pumps 4.5 Special Wastes & Chemical Drainage 4.6 Indirect & Special Waste Piping

5 Chapter 5: Plumbing Venting Systems

5.1 Venting Principles & Vent Stack Sizing 5.2 Individual, Common, & Wet Venting 5.3 Circuit, Loop, & Island Venting 5.4 Air Admittance Valves & Combination Vents 5.5 Vent Terminals & Roof Penetrations

6 Chapter 6: Traps, Interceptors, & Separators

6.1 Trap Requirements & Hydraulic Seals 6.2 Trap Seal Protection & Primers 6.3 Grease Interceptors & Hydromechanical Traps 6.4 Oil, Sand, & Flammable Liquid Separators 6.5 Backwater Valves & Flood Protection

7 Chapter 7: Storm Drainage & Exterior Systems

7.1 Storm Drainage Sizing & Roof Drains 7.2 Subsoil Drainage & Sump Systems 7.3 Combined & Separated Sewer Connections 7.4 Rainwater Harvesting & Non-Potable Systems

8 Chapter 8: Fuel Gas Piping & Appliance Venting

8.1 Fuel Gas Piping Materials & Joints 8.2 Fuel Gas Pipe Sizing & Pressure Drop 8.3 Gas Pipe Inspection, Testing, & Purging 8.4 Appliance Venting & Draft Hoods 8.5 Combustion Air & Appliance Location

7.4 Rainwater Harvesting & Non-Potable Systems

Key Takeaways Explain This Topic AI

Non-potable water distribution lines carrying harvested rainwater or greywater must be continuously identified with purple color-coding (Pantone 512/522) or purple warning tape.

First-flush diverters must divert the initial 10 to 20 gallons of rainwater runoff per 1,000 square feet of roof area to isolate dust, debris, and atmospheric contaminants from storage cisterns.

Approved greywater sources include bathroom lavatories, showers, bathtubs, and clothes washers; kitchen sink and toilet waste (blackwater) are strictly prohibited.

Potable water backup lines feeding non-potable storage cisterns must be protected by an physical air gap located above the overflow rim of the tank.

Recycled water used for indoor toilet flushing or spray irrigation requires 5-micron filtration and disinfection (UV or chlorination) to meet non-potable water quality standards.

Last updated: August 2026

  • Rainwater Harvesting & Non-Potable Systems
  • 1. Principles of Rainwater Harvesting & Non-Potable Conservation

Rainwater harvesting and greywater recycling systems collect, treat, and reuse non-potable water for non-potable applications—such as water closet/urinal flushing, subterranean landscape irrigation, cooling tower makeup, and industrial washdown. Implementing non-potable reuse systems reduces municipal potable water demand and mitigates urban stormwater runoff volumes.

Non-potable plumbing design is governed by IPC Chapter 13 (Non-Potable Water Systems) and UPC Chapter 13 (Non-Potable Rainwater Catchment Systems) . Because non-potable piping runs inside or adjacent to buildings containing potable drinking water systems, model codes establish strict physical separation, pipe identification, and backflow isolation mandates to eliminate cross-connection contamination hazards.

2. First-Flush Diversion Mechanics & Cistern Design

When rainfall begins after a dry period, the initial water washing off a roof catchment surface carries accumulated environmental debris—including bird droppings, dust, pollen, heavy metals, leaf litter, and atmospheric soot. This heavily contaminated initial volume is known as the first-flush .

First-Flush Diverter Sizing Mandate

Under model plumbing codes, non-potable rainwater harvesting systems must incorporate an automatic First-Flush Diverter installed upstream of storage cistern entry: First-Flush Volume ( V ff ) = 10 to 20 Gallons per 1 , 000 sq ft of Roof Area \text{First-Flush Volume } (V_{\text{ff}}) = 10 \text{ to } 20 \text{ Gallons per } 1,000 \text{ sq ft of Roof Area} First-Flush Volume ( V ff ​ ) = 10 to 20 Gallons per 1 , 000 sq ft of Roof Area ROOF GUTTER RUNOFF

  • │
  • ▼
  • ┌───────────────────┐
  • │ DEBRIS MESH SCREEN│ (Removes Leaves / Twigs)
  • └─────────┬─────────┘
  • │
  • ┌─────────────────┴─────────────────┐
  • │ │
  • ▼ ▼
  • ┌───────────────────┐ ┌───────────────────┐
  • │ FIRST-FLUSH DRAIN │ │ CLEAN WATER TO │
  • │ DIVERTER PIPE │ │ STORAGE CISTERN │
  • │ (Fills First 10- │ └───────────────────┘
  • │ 20 gal/1000 sq ft│ ▲
  • │ Floating Ball │ │
  • │ Seals Top) ├─────────────────────────┘
  • └─────────┬─────────┘ (Once Chamber Fills, Water
  • │ Diverts to Tank)
  • ▼ Slow Drip Drain
  • Operational Mechanics of First-Flush Diverters

Initial Flow: As rain begins, dirty runoff flows down the leader and enters a vertical storage pipe chamber (the diverter body).

Chamber Filling & Seal: As the diverter chamber fills to its calibrated capacity ( 10 – 20 gal/1,000 sq ft 10\text{--}20 \text{ gal/1,000 sq ft} 10 – 20 gal/1,000 sq ft ), a lightweight floating ball inside the chamber rises. When the chamber is full, the ball seats tightly against an upper rubber orifice seal.

Diversion to Cistern: Once sealed, all subsequent clean rainwater bypasses the full chamber and flows directly into the main storage cistern.

Drain Down: A calibrated bottom bleed orifice (drip emitter) slowly empties the dirty first-flush chamber over 24 to 48 hours, resetting the diverter for the next rainfall event.

3. Greywater Source Classification & Code Restrictions

Greywater is defined as untreated liquid waste collected from specific domestic fixtures that has not come into contact with infectious organic human waste or toxic chemicals. ┌──────────────────────────────────────────────────────────────────────────┐

  • │ ALLOWABLE VS. PROHIBITED SOURCES │
  • ├────────────────────────────────────┬─────────────────────────────────────┤
  • │ APPROVED GREYWATER SOURCES │ PROHIBITED BLACKWATER SOURCES │
  • ├────────────────────────────────────┼─────────────────────────────────────┤
  • │ • Bathroom Lavatories / Sinks │ • Water Closets / Toilets & Bidets │
  • │ • Bathtubs & Shower Stalls │ • Kitchen Sinks & Food Waste Grinders│
  • │ • Clothes Washing Machines │ • Commercial Dishwashers │
  • │ • Laundry Trays / Sinks │ • Soil Waste & Chemical Drains │
  • └────────────────────────────────────┴─────────────────────────────────────┘
  • Why Kitchen Sinks and Toilets Are Prohibited

Kitchen sink discharge contains heavy concentrations of Fats, Oils, and Grease (FOG), food solids, and high bacterial loads from raw meat handling. Toilet and urinal waste contains human pathogens, E. coli, and nitrogenous matter. Discharges from kitchen sinks, dishwashers, and toilets are classified as Blackwater and must discharge directly into the sanitary drainage system.

4. Non-Potable Pipe Identification & Purple Pipe Marking Standards

To prevent plumbers or maintenance personnel from accidentally connecting a potable drinking line into a recycled water pipe, model codes enforce strict universal color coding:

The Purple Pipe Standard (IPC 1301.3 & UPC 1301.4)

Color Code: All non-potable water distribution piping, fittings, valves, outlets, and hose bibbs must be manufactured of Purple material (specifically Pantone 512 or 522) or wrapped in continuous purple identification tape.

Mandatory Stenciling: Non-potable piping must be permanently marked or stenciled in prominent white lettering stating:

"CAUTION: NON-POTABLE WATER - DO NOT DRINK"

Labeling Intervals: Stenciling or warning tape must be applied along the entire length of the pipe at intervals of not more than 20 feet (6.1 meters) and at every wall/floor penetration.

Hose Bibb Lockouts: Exterior hose bibbs connected to non-potable recycled water must feature removable lockable handles and warning signs to prevent public drinking.

5. Cross-Connection Protection, Air Gaps, and Treatment Requirements

When non-potable rainwater or greywater cisterns run dry during drought periods, an auxiliary potable water makeup line must supply supplemental water to keep fixtures functional.

Mandatory Air Gap Backup Isolation

To prevent contaminated non-potable cistern water from back-siphoning into the municipal drinking water supply, the potable makeup supply line MUST be isolated by an approved Air Gap .

Air Gap Dimension: The vertical distance between the bottom of the potable supply pipe outlet and the flood-level rim of the cistern or receipt tank must be at least twice the effective diameter of the supply pipe ( 2 × d 2 \times d 2 × d ) , and never less than 1.0 inch (25 mm) .

Direct Cross-Connection Prohibited: Under no circumstances may a potable water supply pipe be directly connected into non-potable piping or immersed below the overflow rim of a non-potable tank, even with a check valve. POTABLE WATER SUPPLY LINE

  • │
  • ▼
  • ════════════════════ Pipe Outlet Datum
  • │
  • │ Air Gap Height (Min 2 x Pipe Dia, Min 1.0")
  • │
  • ════════════════════ Cistern Overflow Rim / Flood Elevation
  • ┌──────────────────┐
  • │ NON-POTABLE │
  • │ STORAGE CISTERN │ (Recycled Rainwater / Greywater)
  • └──────────────────┘
  • Non-Potable Water Quality Treatment Standards

Before recycled rainwater or greywater can be used indoors for toilet flushing or spray irrigation, it must pass through continuous filtration and disinfection to protect public health:

Application Filtration Requirement Disinfection Standard Permissible E. coli Limit

Toilet & Urinal Flushing 5-micron sediment filter Chlorine / UV Disinfection < 2.2 CFU / 100 mL < 2.2 \text{ CFU / 100 mL} < 2.2 CFU / 100 mL

Subsurface Irrigation 100-mesh (150 micron) strainer No disinfection required < 200 CFU / 100 mL < 200 \text{ CFU / 100 mL} < 200 CFU / 100 mL

Spray / Surface Irrigation 5-micron sediment filter Chlorine residual ( > 1.0 mg/L > 1.0 \text{ mg/L} > 1.0 mg/L ) / UV Non-detectable ( 0 CFU 0 \text{ CFU} 0 CFU )

  • 6. Worked Example: Rainwater Catchment & First-Flush Calculation
  • Scenario

A commercial building has a metal roof catchment area of 12,000 square feet. The local area receives an average annual rainfall of 36 inches. A rainwater harvesting system is being installed to collect roof runoff for indoor toilet flushing. Plumbers must size the required first-flush diverter volume and calculate the total estimated annual rainwater yield .

Step 1: Calculate First-Flush Diversion Volume Requirement:

Code standard requires 15 gallons per 1,000 sq ft of roof catchment area. V ff = ( 12 , 000 sq ft 1 , 000 sq ft ) × 15 gallons = 12 × 15 = 180 gallons V_{\text{ff}} = \left(\frac{12,000 \text{ sq ft}}{1,000 \text{ sq ft}}\right) \times 15 \text{ gallons} = 12 \times 15 = 180 \text{ gallons} V ff ​ = ( 1 , 000 sq ft 12 , 000 sq ft ​ ) × 15 gallons = 12 × 15 = 180 gallons

The first-flush chamber must be sized to hold at least 180 gallons before diverting clean water to the cistern.

Step 2: Sizing First-Flush Diverter Piping (using 10-inch PVC pipe):

10-inch PVC pipe holds approximately 4.08 gallons per linear foot . Length of 10" Pipe = 180 gallons 4.08 gal/ft = 44.1 linear feet \text{Length of 10" Pipe} = \frac{180 \text{ gallons}}{4.08 \text{ gal/ft}} = 44.1 \text{ linear feet} Length of 10" Pipe = 4.08 gal/ft 180 gallons ​ = 44.1 linear feet

Installation: Install two parallel 10-inch vertical diverter pipes, each 22.1 feet long, equipped with floating ball seals and 1/4-inch bottom drip emitters.

Step 3: Calculate Total Annual Rainwater Catchment Yield:

Runoff efficiency factor for smooth metal roof = 0.90. Annual Yield (gal) = Area (sq ft) × Rainfall (in) × 0.6233 gal/sq ft/in × Efficiency \text{Annual Yield (gal)} = \text{Area (sq ft)} \times \text{Rainfall (in)} \times 0.6233 \text{ gal/sq ft/in} \times \text{Efficiency} Annual Yield (gal) = Area (sq ft) × Rainfall (in) × 0.6233 gal/sq ft/in × Efficiency Annual Yield = 12 , 000 sq ft × 36 in × 0.6233 × 0.90 = 242 , 339 gallons/year \text{Annual Yield} = 12,000 \text{ sq ft} \times 36 \text{ in} \times 0.6233 \times 0.90 = 242,339 \text{ gallons/year} Annual Yield = 12 , 000 sq ft × 36 in × 0.6233 × 0.90 = 242 , 339 gallons/year

Step 4: Potable Backup Specification:

Install a 1-inch potable supply pipe over the top of the cistern equipped with a 2-inch minimum air gap above the cistern overflow rim to provide automatic backup during dry periods.

Loading diagram... Rainwater Harvesting & Non-Potable Recycled Water System Schematic