Study guide
7.3 Combined & Separated Sewer Connections
Journeyman Plumber Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Administration, Code Enforcement, & Safety
1.1 Administration, Permits, and Inspections 1.2 General Regulations & Building Integrity 1.3 Material Standards & Piping Joining Methods 1.4 Plumbing Math & Water Calculations 1.5 Isometric Drawings & Blueprint Reading
2 Chapter 2: Plumbing Fixtures, Appliances, & Water Heaters
Plumbing Fixtures & Minimum Standards Water Heaters & Safety Devices Special Fixtures & Healthcare Plumbing Fixture Installation & Connection Rules Water Conservation & Flow Rates
3 Chapter 3: Water Supply & Distribution Systems
Water Service Piping & Main Sizing Water Supply Sizing & WSFU Calculations Backflow Prevention & Cross-Connection Control Water Pressure Boosters & Reducing Valves Hot Water Distribution & Recirculation Disinfection & Potable Water Quality
4 Chapter 4: Sanitary Drainage Systems & DFU Sizing
4.1 Sanitary Drainage Fundamentals & DFU 4.2 Drainage Pipe Sizing & Minimum Slopes 4.3 Building Drains, Sewers, & Cleanouts 4.4 Sumps, Ejectors, & Sewage Pumps 4.5 Special Wastes & Chemical Drainage 4.6 Indirect & Special Waste Piping
5 Chapter 5: Plumbing Venting Systems
5.1 Venting Principles & Vent Stack Sizing 5.2 Individual, Common, & Wet Venting 5.3 Circuit, Loop, & Island Venting 5.4 Air Admittance Valves & Combination Vents 5.5 Vent Terminals & Roof Penetrations
6 Chapter 6: Traps, Interceptors, & Separators
6.1 Trap Requirements & Hydraulic Seals 6.2 Trap Seal Protection & Primers 6.3 Grease Interceptors & Hydromechanical Traps 6.4 Oil, Sand, & Flammable Liquid Separators 6.5 Backwater Valves & Flood Protection
7 Chapter 7: Storm Drainage & Exterior Systems
7.1 Storm Drainage Sizing & Roof Drains 7.2 Subsoil Drainage & Sump Systems 7.3 Combined & Separated Sewer Connections 7.4 Rainwater Harvesting & Non-Potable Systems
8 Chapter 8: Fuel Gas Piping & Appliance Venting
8.1 Fuel Gas Piping Materials & Joints 8.2 Fuel Gas Pipe Sizing & Pressure Drop 8.3 Gas Pipe Inspection, Testing, & Purging 8.4 Appliance Venting & Draft Hoods 8.5 Combustion Air & Appliance Location
7.3 Combined & Separated Sewer Connections
Key Takeaways Explain This Topic AI
Sanitary drainage and storm drainage systems inside a building must remain completely separate up to the point of connection to public sewer infrastructure outside the building structure.
Where a public combined sewer is utilized, the building storm drain may connect to the building sanitary sewer outside the building foundation or at the property line, subject to local utility approval.
A building storm drain connecting to a combined public sewer must be equipped with an approved single or double storm drain trap with accessible cleanouts located near the building wall.
Storm drainage inlets or floor drains located below the elevation of the nearest upstream public manhole cover must be protected by an approved backwater valve to prevent surcharge flooding.
Unpolluted clear-water waste (cooling water, condensate) must not discharge into the sanitary sewer system if an approved storm sewer or recycling system is available.
Last updated: August 2026
- Combined & Separated Sewer Connections
- 1. Separated vs. Combined Drainage Infrastructure Principles
In municipal civil engineering and building plumbing design, wastewater and stormwater collection networks fall into two structural classifications:
Separated Sewer Systems: Municipalities operate two distinct underground utility main networks: a Sanitary Sewer Main (conveying domestic sewage and industrial liquid waste to a wastewater treatment plant) and a Storm Sewer Main (conveying surface rainwater runoff directly to rivers, lakes, or retention basins without chemical treatment).
Combined Sewer Systems: Older urban infrastructures utilize a single underground main pipe—a Combined Public Sewer —that collects both domestic sanitary sewage and surface stormwater runoff in a shared municipal conduit.
Mandatory Interior Building Separation Rule
Regardless of whether the public street utility sewer is separated or combined, both the International Plumbing Code (IPC 1101.2) and Uniform Plumbing Code (UPC 1101.3) enforce a strict, mandatory rule:
Sanitary drainage piping and storm drainage piping inside a building MUST remain completely separate.
Connecting storm vertical leaders, roof drains, or area drains into interior sanitary stacks or branches is strictly prohibited. Combining flows inside the building structure creates severe public health hazards: during torrential storms, heavy roof runoff fills sanitary pipes, blowing out fixture trap seals and backing up raw human sewage into lower-floor sinks, showers, and floor drains. INTERIOR BUILDING PIPING (MUST REMAIN SEPARATE)
- SANITARY WASTE STACK STORM LEADER STACK
- (Soil / Waste Fixtures) (Roof Drains / Scuppers)
- │ │
- ▼ ▼
- ┌─────────────────┐ ┌─────────────────┐
- │ Building Drain │ │ Building Storm │
- │ (Sanitary) │ │ Drain │
- └────────┬────────┘ └────────┬────────┘
- │ │
- ═════════╪════════════════════════════════════╪════════════ Foundation Wall Boundary
- │ │
- │ EXTERIOR POINT OF COMBINED │
- │ CONNECTION (OUTSIDE WALL) │
- │ ┌───────────────────────────┐ │
- │ │ Building Storm Drain Trap │◄──┤ (Trap Sized for Storm GPM)
- │ └─────────────┬─────────────┘ │
- ▼ ▼ │
- ┌─────────────────────────────────────────┴─┐
- │ COMBINED BUILDING SEWER │
- └───────────────────┬───────────────────────┘
- ▼ To Municipal Combined Main
- 2. Building Storm Drain Trapping Requirements on Combined Sewer Connections
When a building storm drain discharges into a public combined sewer or a combined building sewer outside the foundation wall, a unique atmospheric hazard arises. Public combined sewers carry foul sewer gas, volatile organic compounds, and hydrogen sulfide. Without a barrier, sewer gases would travel up exterior storm leaders and discharge through roof drains, re-entering building air intakes or contaminating roof areas.
Building Storm Drain Trap Specifications
Under IPC 1111 and UPC 1101.12 , when a storm drain connects to a combined sewer, an approved Building Storm Drain Trap must be installed on the horizontal storm drain line prior to its connection to the combined sewer:
Trap Location: The trap must be located outside the building wall or inside the building near the point of exit, positioned in an accessible location.
Trap Seal Depth: The storm trap must maintain a liquid seal depth of not less than 2 inches (51 mm) and not more than 4 inches (102 mm) .
Cleanouts: The trap must be equipped with accessible cleanouts on both the upstream (building) and downstream (sewer) sides of the trap seal to permit mechanical snaking.
Air Relief / Venting: Traps installed on combined storm lines must be vented on the building side or connected to leaders that provide adequate relief to prevent trap seal siphonage during surge flows.
3. Backflow Prevention & Backwater Valve Mandates for Storm Outlets
During extreme weather events, municipal combined sewers frequently become surcharged (filled above crown elevation under hydrostatic pressure). When a combined street sewer surcharges, liquid sewage backs up through lateral connections toward connected buildings.
Sub-Grade Storm Inlets & Backwater Valves
Any storm drainage inlet, area drain, driveway drain, or window well drain connected to a combined sewer system whose rim elevation is located below the elevation of the nearest upstream public sewer manhole cover must be protected against sewer surcharge. UPSTREAM STREET MANHOLE
- ══════════════════════ Rim / Cover Elevation
- │
- DRIVEWAY AREA DRAIN │ Surcharged Hydraulic Grade Line
- (Low-Elevation Rim) │ ‑ ‑ ‑ ‑ ‑ ‑ ‑ ‑ ‑ ‑ ‑ ‑ ‑ ‑ ‑ ‑ ‑ ‑
- │ │
- ┌──────┴──────┐ │
- │ Drain Grate │ │
- └──────┬──────┘ │
- │ │
- ┌──────┴──────────────┐ │
- │ BACKWATER VALVE │ │
- │ (Normally Open Flap)│ │
- └──────┬──────────────┘ │
- ▼ ▼
- ┌──────────────────────────────────────────────┐
- │ COMBINED SEWER LATERAL │
- └──────────────────────────────────────────────┘
Backwater Valve Mandate: An approved backwater valve (complying with ASME A112.14.1) must be installed on the horizontal branch line serving low-level storm drains.
Operational Mechanics: The backwater valve contains a balanced, swing-check flap mechanism. Under normal gravity flow, the flap hangs open to permit drainage. When main sewer surcharge forces water backward into the lateral, the reversed flow lifts the flap tightly against its seat, preventing sewage from flooding the driveway or lower floor drains.
Accessibility: Backwater valves must be housed in an accessible pit or provided with an access cover for routine inspection and removal of debris.
4. Converting Storm Flow (GPM) and Sanitary Fixture Units (DFU) for Pipe Sizing
When sizing a combined building sewer outside a building, plumbers must combine the sanitary hydraulic load (measured in DFUs) and the storm hydraulic load (measured in GPM) into a single equivalent hydraulic load.
Code Conversion Equivalence
Model plumbing codes establish a standard equivalence factor between Drainage Fixture Units and Stormwater GPM:
1 GPM of Stormwater Flow = 2 Drainage Fixture Units (DFUs) (for sizing combined horizontal building sewers).
Sizing Procedure for Combined Building Sewers
Calculate the total Sanitary DFU load of all fixtures in the building.
Calculate the peak Stormwater GPM load from projected roof and paved areas ( Q = A × I × 0.0104 Q = A \times I \times 0.0104 Q = A × I × 0.0104 ).
Convert Stormwater GPM to equivalent DFUs ( G P M × 2 = Storm DFUs GPM \times 2 = \text{Storm DFUs} GPM × 2 = Storm DFUs ).
Add Sanitary DFUs + Storm DFUs = Total Combined DFUs.
Size the horizontal combined building sewer using standard DFU sizing tables (IPC Table 710.1(1) / UPC Table 717.1) at the designated slope (1/8 or 1/4 in/ft).
Sewer System Type Interior Separation Exterior Connection Point Trapping Mandate Backwater Protection
Separated Sanitary Strictly Separated Connects to Public Sanitary Main Fixture Traps Mandatory Required if fixtures below manhole
Separated Storm Strictly Separated Connects to Public Storm Main No Building Trap Required Required if inlets below manhole
Combined Sewer Strictly Separated Combined outside building wall Building Storm Trap Required Backwater Valve required on low inlets
5. Environmental Discharge Standards: Clear Water vs. Contaminated Runoff
Modern environmental standards enforced by the EPA National Pollutant Discharge Elimination System (NPDES) and local plumbing codes differentiate between clear-water waste and contaminated runoff:
Unpolluted Clear-Water Waste: Water from air conditioning condensate drains, refrigeration coils, ice machines, and commercial drinking fountains contains no organic pathogens. Model codes require clear-water waste to discharge into storm sewers, drywells, or non-potable recycling systems, forbidding discharge into sanitary sewers where municipal capacity is limited.
Industrial & Oil-Contaminated Stormwater: Runoff from commercial parking garages, auto repair bays, and gas station forecourts carries petroleum hydrocarbons and heavy metals. This runoff must pass through an approved Oil-Water Separator / Interceptor before discharging to a combined sewer or storm main.
- 6. Worked Example: Combined Sewer Connection Sizing & Trapping Layout
- Scenario
A commercial building has a sanitary load of 120 DFUs . The building roof measures 8,000 square feet in a location with a 100-year rainfall intensity of 2.5 inches per hour . The storm drain and sanitary drain run separately inside the building and exit through the foundation wall to connect into a single combined building sewer pitched at 1/4 in/ft (2.08%) slope .
Step 1: Calculate Stormwater Flow Rate (GPM): Q = A × I × 0.0104 Q = A \times I \times 0.0104 Q = A × I × 0.0104 Q = 8 , 000 sq ft × 2.5 in/hr × 0.0104 = 208 GPM Q = 8,000 \text{ sq ft} \times 2.5 \text{ in/hr} \times 0.0104 = 208 \text{ GPM} Q = 8 , 000 sq ft × 2.5 in/hr × 0.0104 = 208 GPM
Step 2: Convert Storm Flow GPM to Equivalent DFUs: Storm DFUs = 208 GPM × 2 = 416 DFUs \text{Storm DFUs} = 208 \text{ GPM} \times 2 = 416 \text{ DFUs} Storm DFUs = 208 GPM × 2 = 416 DFUs
Step 3: Calculate Total Combined DFU Load: Total Combined Load = 120 Sanitary DFUs + 416 Storm DFUs = 536 DFUs \text{Total Combined Load} = 120 \text{ Sanitary DFUs} + 416 \text{ Storm DFUs} = 536 \text{ DFUs} Total Combined Load = 120 Sanitary DFUs + 416 Storm DFUs = 536 DFUs
Step 4: Size Horizontal Combined Sewer at 1/4 in/ft Slope:
Consult Horizontal Building Sewer Sizing Table at 1/4 in/ft slope:
4-inch sewer capacity = 216 DFUs ( Insufficient: 536 > 216 536 > 216 536 > 216 ).
5-inch sewer capacity = 480 DFUs ( Insufficient: 536 > 480 536 > 480 536 > 480 ).
6-inch sewer capacity = 840 DFUs ( Sufficient: 536 ≤ 840 536 \le 840 536 ≤ 840 ).
Selection: 6-inch combined horizontal building sewer.
Step 5: Trapping Mandate Check:
Install a 6-inch building storm drain trap equipped with dual cleanouts on the exterior storm line immediately before it joins the 6-inch combined sewer pipe.