Study guide

Disinfection & Potable Water Quality

Journeyman Plumber Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Administration, Code Enforcement, & Safety

1.1 Administration, Permits, and Inspections 1.2 General Regulations & Building Integrity 1.3 Material Standards & Piping Joining Methods 1.4 Plumbing Math & Water Calculations 1.5 Isometric Drawings & Blueprint Reading

2 Chapter 2: Plumbing Fixtures, Appliances, & Water Heaters

Plumbing Fixtures & Minimum Standards Water Heaters & Safety Devices Special Fixtures & Healthcare Plumbing Fixture Installation & Connection Rules Water Conservation & Flow Rates

3 Chapter 3: Water Supply & Distribution Systems

Water Service Piping & Main Sizing Water Supply Sizing & WSFU Calculations Backflow Prevention & Cross-Connection Control Water Pressure Boosters & Reducing Valves Hot Water Distribution & Recirculation Disinfection & Potable Water Quality

4 Chapter 4: Sanitary Drainage Systems & DFU Sizing

4.1 Sanitary Drainage Fundamentals & DFU 4.2 Drainage Pipe Sizing & Minimum Slopes 4.3 Building Drains, Sewers, & Cleanouts 4.4 Sumps, Ejectors, & Sewage Pumps 4.5 Special Wastes & Chemical Drainage 4.6 Indirect & Special Waste Piping

5 Chapter 5: Plumbing Venting Systems

5.1 Venting Principles & Vent Stack Sizing 5.2 Individual, Common, & Wet Venting 5.3 Circuit, Loop, & Island Venting 5.4 Air Admittance Valves & Combination Vents 5.5 Vent Terminals & Roof Penetrations

6 Chapter 6: Traps, Interceptors, & Separators

6.1 Trap Requirements & Hydraulic Seals 6.2 Trap Seal Protection & Primers 6.3 Grease Interceptors & Hydromechanical Traps 6.4 Oil, Sand, & Flammable Liquid Separators 6.5 Backwater Valves & Flood Protection

7 Chapter 7: Storm Drainage & Exterior Systems

7.1 Storm Drainage Sizing & Roof Drains 7.2 Subsoil Drainage & Sump Systems 7.3 Combined & Separated Sewer Connections 7.4 Rainwater Harvesting & Non-Potable Systems

8 Chapter 8: Fuel Gas Piping & Appliance Venting

8.1 Fuel Gas Piping Materials & Joints 8.2 Fuel Gas Pipe Sizing & Pressure Drop 8.3 Gas Pipe Inspection, Testing, & Purging 8.4 Appliance Venting & Draft Hoods 8.5 Combustion Air & Appliance Location

Disinfection & Potable Water Quality

Key Takeaways Explain This Topic AI

New or repaired potable water piping must be disinfected with a free chlorine dose of at least 50 ppm for 24 hours or 200 ppm for 3 hours.

A minimum free chlorine residual of 5 ppm (for the 24-hour method) or 25 ppm (for the 3-hour method) must remain at all test outlets at retention end.

Following chemical retention, piping must be flushed with potable water until residual chlorine matches the incoming municipal water supply level.

Bacteriological testing for Total Coliform and E. coli by an accredited lab is mandatory after final flushing before system commissioning.

Chemical dosing equipment must be physically isolated from the municipal supply line using an approved backflow preventer or air gap during chlorination.

Last updated: August 2026

Disinfection & Potable Water Quality

Exam Tip: Memorize the two chlorination dosage/retention ratios: 50 ppm for 24 hours (retaining at least 5 ppm residual) OR 200 ppm for 3 hours (retaining at least 25 ppm residual). Water samples for bacteriological testing must show zero coliform bacteria before the system can be approved for occupancy.

Health Imperatives of Water System Disinfection

During building construction, pipe installation, or underground main repairs, internal piping surfaces are exposed to dirt, pipe joint compounds, solder flux, organic matter, and pathogenic microorganisms—including Escherichia coli , Pseudomonas aeruginosa , and Legionella pneumophila .

Under IPC Section 610.1 and UPC Section 660.0 , all newly constructed potable water systems, as well as existing systems altered or contaminated during repair work, must be thoroughly disinfected before being placed into service.

Code Mandates (IPC Section 610 & AWWA C651)

The standard procedure for disinfecting potable water mains follows the AWWA C651 (American Water Works Association) standard, executed in five distinct sequential phases: +--------------------------------------------------------------------------+

  • | POTABLE WATER DISINFECTION SEQUENCE |
  • | |
  • | [ Phase 1: High-Velocity Pre-Flush (Min 2.5 fps Scouring Velocity) ] |
  • | || |
  • | [ Phase 2: Chlorination Dosing (50 ppm or 200 ppm Concentration) ] |
  • | || |
  • | [ Phase 3: Chemical Retention Period (24 Hours or 3 Hours Soak) ] |
  • | || |
  • | [ Phase 4: Final Flushing & Dechlorination (Match Street Residual) ] |
  • | || |
  • | [ Phase 5: Bacteriological Sampling (Coliform & E. coli Lab Test) ] |
  • +--------------------------------------------------------------------------+
  • Phase 1: High-Velocity Scouring & System Flushing

Prior to introducing chemical disinfectants, the piping network must be thoroughly flushed with clean potable water to scour out construction sand, metal filings, flux, and debris.

Scouring Velocity: Flush water must achieve a internal pipe velocity of not less than 2.5 feet per second (0.76 m/s) .

Duration: Flushing must continue until the discharge water runs completely clear at all hydrants, blow-offs, and fixture outlets.

Phase 2: Chlorination Methods & Chemical Dosing

Plumbing codes permit two standard methods for chemical chlorination dosing:

Method 1: Continuous Feed 24-Hour Method (Standard)

Initial Concentration: Water injected into the system must contain at least 50 parts per million (ppm / mg/L) of available free chlorine.

Retention Time: The chlorinated water must be retained in all parts of the piping system for a minimum of 24 hours .

Minimum Final Residual: At the end of the 24-hour retention period, the free chlorine residual measured at any point in the system must not be less than 5 ppm (mg/L) . If residual drops below 5 ppm, the entire process must be repeated.

Method 2: High-Concentration 3-Hour Method (Accelerated)

Initial Concentration: Water injected into the system must contain at least 200 parts per million (200 ppm / mg/L) of available free chlorine.

Retention Time: The solution must be retained in the piping system for at least 3 hours .

Minimum Final Residual: At the conclusion of 3 hours, free chlorine residual must measure not less than 25 ppm (mg/L) throughout all system outlets.

Chlorination Method Initial Dose (Available Chlorine) Retention Soak Time Minimum Required Final Residual Application Context

  • Standard 24-Hour Method 50 ppm (mg/L) 24 hours 5 ppm (mg/L) Large commercial buildings, underground mains
  • Accelerated 3-Hour Method 200 ppm (mg/L) 3 hours 25 ppm (mg/L) Emergency main repairs, small building remodels
  • Chemical Dosing Formula & Worked Calculation

Chlorine is commonly introduced using liquid Sodium Hypochlorite (household bleach ~5.25% or commercial grade ~12.5%) or Calcium Hypochlorite granules/tablets (65% available chlorine) .

Volumetric Chemical Dosing Equation V chemical (gal) = C target (ppm) × V system (gal) C solution (%) × 10 , 000 \text{V}_{\text{chemical (gal)}} = \frac{C_{\text{target (ppm)}} \times V_{\text{system (gal)}}}{C_{\text{solution (\%)}} \times 10,000} V chemical (gal) ​ = C solution (%) ​ × 10 , 000 C target (ppm) ​ × V system (gal) ​ ​

Worked Example: Calculate the required volume of 12.5% commercial sodium hypochlorite needed to dose a 2,000-gallon building distribution system to 50 ppm available chlorine.

Apply Equation: V chemical = 50 ppm × 2 , 000 gal 12.5 × 10 , 000 = 100 , 000 125 , 000 = 0.80 gallons \text{V}_{\text{chemical}} = \frac{50 \text{ ppm} \times 2,000 \text{ gal}}{12.5 \times 10,000} = \frac{100,000}{125,000} = \mathbf{0.80 \text{ gallons}} V chemical ​ = 12.5 × 10 , 000 50 ppm × 2 , 000 gal ​ = 125 , 000 100 , 000 ​ = 0.80 gallons

Convert to Fluid Ounces: 0.80 gal × 128 fl oz/gal = 102.4 fluid ounces 0.80 \text{ gal} \times 128 \text{ fl oz/gal} = \mathbf{102.4 \text{ fluid ounces}} 0.80 gal × 128 fl oz/gal = 102.4 fluid ounces (Approximately 3.2 quarts of 12.5% bleach solution).

Phase 4: Final Flushing & Dechlorination Procedures

Following successful chemical retention, the heavily chlorinated water must be purged completely from the system using potable water until the residual chlorine concentration at all outlets matches incoming municipal main water (typically 0.2 to 1.0 ppm ).

Environmental Dechlorination Regulations

Directly discharging water containing 5 ppm to 200 ppm chlorine into storm sewers, lakes, or streams is strictly prohibited by state environmental protection agencies (EPA) due to extreme toxicity to fish and aquatic ecosystems.

Dechlorination Agents: Neutralizing chemicals such as Sodium Thiosulfate ( N a 2 S 2 O 3 Na_2S_2O_3 N a 2 ​ S 2 ​ O 3 ​ ) , Sodium Bisulfite , or Ascorbic Acid (Vitamin C) must be injected into the flushing discharge stream.

Reaction Stoichiometry: Approximately 2 to 3 lbs of Sodium Thiosulfate neutralizes 1 lb of pure free chlorine.

Phase 5: Bacteriological Sampling & Certification

Flushing away the chlorine does not automatically certify system safety. Microbiological validation is mandatory.

Sampling Protocol: Water samples must be collected from representative points (end of main line, longest branch, top floor) using sterile sample bottles containing Sodium Thiosulfate (to instantly neutralize lingering chlorine traces during transit).

Laboratory Testing: Samples are submitted to an EPA-accredited water testing laboratory to perform a Total Coliform & E. coli Test (via Membrane Filtration or Colilert Method).

Pass / Fail Criteria:

PASS: Zero Total Coliform bacteria detected per 100 mL sample. The system is certified safe for human consumption.

FAIL: Presence of Coliform or E. coli detected. The building distribution system MUST be re-flushed, re-chlorinated, retained, and re-tested until two consecutive negative bacteriological reports are obtained.

Loading diagram... Potable Water System Disinfection and Bacteriological Certification Process Flow