Study guide

3.4 Required Dwelling Outlets & Lighting

Kentucky Journeyman Electrician Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Kentucky Licensing, Electrical Theory & Plan Reading

1.1 Kentucky Electrical Licensing Framework & Regulations 1.2 Electrical Fundamentals, Ohm's Law & Power Calculations 1.3 AC Theory, Power Factor & Three-Phase Principles 1.4 Plan Reading: Electrical Drawings, Symbols & Schedules

2 Chapter 2: NEC Organization, Article 100 Definitions & Working Spaces

2.1 NEC Structure, Article 90 Scope & Code Navigation 2.2 Essential Article 100 Definitions 2.3 Article 110 Installation Requirements & Equipment Working Spaces

3 Chapter 3: Branch Circuits & Receptacle Outlets

3.1 Branch Circuit Ratings & Conductor Sizing 3.2 Multiwire Branch Circuits & Identification 3.3 GFCI and AFCI Protection Requirements 3.4 Required Dwelling Outlets & Lighting

4 Chapter 4: Feeders, Outside Branch Circuits & Calculations

4.1 Feeder Conductor Sizing & Continuous Loads 4.2 Feeder Tap Rules & Overcurrent Protection 4.3 Outside Branch Circuits & Feeders

5 Chapter 5: Services & Service Equipment

5.1 Service Conductors, Overhead & Underground 5.2 Service Disconnecting Means & Equipment Ratings 5.3 Emergency Disconnects, Surge Protection & Ground Fault Protection

6 Chapter 6: Overcurrent Protection & Tap Rules

6.1 Overcurrent Protection Principles, Fuses & Circuit Breakers 6.2 Small Conductor Protection & Next-Higher-Standard-Rating Rule 6.3 Transformer Secondary & Equipment Protection Taps

7 Chapter 7: Grounding & Bonding — Systems & Electrodes

7.1 Grounding Theory, System Grounding & Grounded Conductors 7.2 Grounding Electrode System & Electrode Types 7.3 Grounding Electrode Conductor Sizing & Installation

8 Chapter 8: Grounding & Bonding — Equipment & Enclosures

8.1 Main & System Bonding Jumpers 8.2 Equipment Grounding Conductors 8.3 Bonding of Raceways, Enclosures & Piping Systems

9 Chapter 9: Wiring Methods, Raceways & Enclosures

9.1 General Wiring Requirements & Underground Installations 9.2 Metal Raceways — EMT, RMC, IMC & FMC 9.3 Nonmetallic Raceways & Flexible Conduits 9.4 Cabinets, Panelboards, Wireways, Cable Trays & Busways

10 Chapter 10: Conductors, Cables, Box Fill & Pull Boxes

10.1 Conductor Types, Insulations & Ampacity Sizing 10.2 Ampacity Derating — Temperature Correction & Conduit Fill Adjustment 10.3 Nonmetallic-Sheathed Cable, MC Cable & Armored Cable 10.4 Box Fill Calculations & Pull Box Sizing

11 Chapter 11: Equipment for General Use

11.1 Switches, Receptacles & Flexible Cords 11.2 Luminaires, Lampholders & Clothes Closets 11.3 Appliances, Space Heating & De-icing Equipment

12 Chapter 12: Motors, Generators, HVAC & Control Circuits

12.1 Motor Full-Load Current & Branch Circuit Conductor Sizing 12.2 Motor Overload & Branch-Circuit Short-Circuit / Ground-Fault Protection 12.3 Motor Disconnecting Means & Motor Controllers 12.4 HVAC Equipment, Transformers & Generators 12.5 Class 1, Class 2 & Class 3 Remote-Control, Signaling & Power-Limited Circuits

13 Chapter 13: Special Occupancies & Conditions

13.1 Hazardous (Classified) Locations 13.2 Commercial Garages, Motor Fuel Dispensing & Spray Areas 13.3 Health Care Facilities & Places of Assembly 13.4 Agricultural Buildings & Swimming Pools 13.5 Manufactured Homes, RV Parks, Marinas & Temporary Installations

14 Chapter 14: Special Equipment, Standby & Communications Systems, Calculations & Exam Strategy

14.1 Solar Photovoltaic Systems, Energy Storage & EV Charging 14.2 Signs, Fire Pumps & Welders 14.3 Emergency Systems, Standby Systems & Fire Alarms 14.4 Communications Systems: Chapter 8 & Intersystem Bonding 14.5 Dwelling Unit & Commercial Load Calculations 14.6 Conduit Fill, Voltage Drop & Exam Day Strategy

3.4 Required Dwelling Outlets & Lighting

Key Takeaways Explain This Topic AI

NEC 210.52(A) mandates general receptacle outlets along any dwelling wall space 2 feet or wider such that no point along the floor line is more than 6 feet from an outlet (maximum 12-foot spacing between outlets).

Kitchen countertop spaces 12 inches or wider require receptacles positioned so no point along the wall line is more than 24 inches from an outlet (maximum 4-foot spacing between outlets) per NEC 210.52(C).

Dwelling units require dedicated 20-ampere branch circuits: at least two small-appliance circuits (210.11(C)(1)), one laundry circuit (210.11(C)(2)), and one bathroom circuit (210.11(C)(3)).

Under the 2023 NEC, receptacles on island and peninsular countertops are optional; if none is installed, provisions for a future receptacle are required, and countertop receptacles may no longer be mounted below the work surface (NEC 210.52(C)(2) and (C)(3)).

NEC 210.70(A) requires wall switch-controlled lighting in all habitable rooms, bathrooms, hallways, stairways, garages, and outdoor entrances, with 3-way switches required for stairways having six or more risers.

Last updated: October 2026

Required Dwelling Outlets & Lighting

The National Electrical Code establishes comprehensive mandates for the placement and spacing of receptacle outlets and lighting outlets in dwelling units. The primary objective of NEC 210.52 and NEC 210.70 is convenience and fire safety: by requiring fixed receptacles at prescribed intervals, the code eliminates the hazardous reliance on flexible extension cords, which represent a leading cause of residential electrical fires. For the Kentucky Journeyman Electrician exam, candidates must demonstrate complete fluency with wall spacing rules, countertop layout rules, dedicated circuit requirements, and lighting switch locations.

1. General Wall Receptacle Outlets: The 6-Foot / 12-Foot Rule (NEC 210.52(A))

NEC 210.52(A) governs receptacle outlet spacing in every habitable room of a dwelling unit, including kitchens, family rooms, dining rooms, living rooms, parlors, libraries, dens, sunrooms, bedrooms, recreation rooms, and similar spaces.

Spacing Requirements (NEC 210.52(A)(1))

Receptacles must be installed along the perimeter wall line such that:

No point measured horizontally along the floor line in any wall space is more than 6 feet (1.8 m) from a receptacle outlet.

This means that the maximum allowable distance between two consecutive receptacle outlets along an unbroken wall is 12 feet (3.7 m) . An appliance with a standard 6-foot power cord can be placed anywhere along the wall and reach a receptacle without an extension cord. [Corner] ──6 ft── [Receptacle 1] ───────12 ft─────── [Receptacle 2] ──6 ft── [Doorway]

What Constitutes "Wall Space"? (NEC 210.52(A)(2))

For the purposes of 210.52(A), a wall space includes:

Any unbroken wall space that is 2 feet (600 mm) or more in width (including spaces around corners).

The space occupied by fixed panels in exterior walls, excluding sliding glass panels (fixed glass panels count as wall space; sliding door panels do not).

The space afforded by fixed room dividers, such as freestanding bar-type counters or railings.

What Does NOT Count as Wall Space?

Openings for doorways and archways.

Fireplaces and hearths.

Closet door openings with bifold or sliding doors that extend down to the floor.

Floor Receptacles (NEC 210.52(A)(3))

Receptacle outlets located on the floor cannot count toward the required wall spacing unless they are located within 18 inches (450 mm) of the wall. Floor receptacles installed out in open room areas provide convenience but do not satisfy the perimeter wall spacing requirement.

2. Small-Appliance Branch Circuits (NEC 210.11(C)(1) & 210.52(B))

Residential kitchens and dining spaces impose substantial electrical loads from high-wattage heating appliances. The NEC addresses this with dedicated small-appliance circuits:

Minimum Circuit Quantity & Rating

Minimum of Two Circuits: Dwelling units must have a minimum of two 20-ampere Small-Appliance Branch Circuits (SABCs) .

Conductor Size: Sized with minimum 12 AWG copper protected by 20A circuit breakers.

Required Areas Served (NEC 210.52(B)(1))

The two or more SABCs must supply all receptacle outlets in the:

  • Kitchen
  • Pantry
  • Breakfast room
  • Dining room
  • Similar areas of a dwelling unit
  • Strict Limitations on SABCs (NEC 210.52(B)(2))

Small-appliance branch circuits are subject to rigid restrictions:

No Lighting Outlets: SABCs shall have no other outlets, specifically prohibiting switched lighting fixtures, under-cabinet lighting, or range hood lights.

No Other Rooms: SABCs cannot supply receptacles in living rooms, hallways, garages, or outdoors.

Permitted Exceptions:

An outlet installed solely for the supply and support of an electric clock in any of the specified rooms.

Receptacles installed to supply power to gas-fired cooking appliances for electronic ignition and clock timers.

A dedicated individual 15A or 20A branch circuit is permitted for a refrigerator in lieu of connecting to the SABC.

3. Kitchen Countertop Receptacles: The 2-Foot / 4-Foot Rule (NEC 210.52(C))

Kitchen countertops are subject to much denser outlet placement than general walls because countertop appliances (blenders, toasters, food processors) have short 2-foot cords to prevent dangling cord hazards.

Wall Countertop Spaces (NEC 210.52(C)(1))

A receptacle outlet must be installed at each wall countertop and work surface space that is 12 inches (300 mm) or wider .

Spacing Rule: Receptacle outlets must be installed so that:

No point along the wall line is more than 24 inches (600 mm) measured horizontally from a receptacle outlet.

The maximum distance between two countertop receptacle outlets along an unbroken countertop is 48 inches (4 feet) . [End of Counter] ──24 in── [Outlet 1] ──────48 in (4 ft)────── [Outlet 2] ──24 in── [Sink Edge]

Separated Spaces (NEC 210.52(C)(1))

Countertop spaces separated by range tops, refrigerators, or sinks are considered separate countertop spaces . For example, a 14-inch strip of counter between a sink and a range top must have its own dedicated receptacle outlet.

Spaces Behind Sinks & Cooktops

If the space behind a sink or cooktop is less than 12 inches (for straight runs) or less than 18 inches (for corner installations), it is not considered countertop space requiring a receptacle.

Island and Peninsular Countertops (NEC 210.52(C)(2) & (C)(3))

The 2023 NEC changed these rules significantly:

Receptacles are optional (210.52(C)(2)): Receptacle outlets are no longer required to serve island or peninsular countertops and work surfaces. If none is installed, provisions for the future addition of a receptacle must be made at the island or peninsula, such as an empty raceway or a cable left for a future outlet. The AHJ judges what counts as adequate provisions.

Older square-foot rules are gone: The 2020 requirement for one receptacle for the first 9 square feet and another for each additional 18 square feet was deleted.

Location limits (210.52(C)(3)): Any receptacle serving a countertop or work surface must be on or above the surface, not more than 20 inches (500 mm) above it, or installed in the surface using a receptacle outlet assembly listed for countertops or work surfaces. The former option of mounting receptacles below the countertop edge was removed.

4. Required Dedicated Branch Circuits & Outlets by Location

Beyond general walls and kitchens, the NEC prescribes dedicated circuits and specific outlet locations throughout the home:

Bathroom Receptacle Outlets (NEC 210.11(C)(3) & 210.52(D))

Location: At least one 125-volt, 15- or 20-ampere receptacle outlet must be installed within 36 inches (900 mm) of the outside edge of each basin (sink).

Circuit Sizing: Must be supplied by a dedicated 20-ampere branch circuit (12 AWG copper).

Permitted Circuit Options:

Option 1: The 20A circuit supplies receptacles in multiple bathrooms , but cannot supply any lighting, exhaust fans, or heaters.

Option 2: The 20A circuit supplies only one single bathroom , in which case it is permitted to supply all loads within that same bathroom (receptacles, vanity lights, exhaust fan, heater), provided no loads outside that bathroom are served.

Laundry Circuit & Outlets (NEC 210.11(C)(2) & 210.52(F))

At least one dedicated 20-ampere branch circuit must supply laundry receptacle outlet(s).

At least one receptacle must be installed within 6 feet of the intended washer location.

The laundry circuit cannot supply any lighting or outlets outside the laundry area.

Outdoor Receptacles (NEC 210.52(E)(1))

One-family and two-family dwellings must have at least two outdoor receptacles : one at the front and one at the back .

Must be accessible while standing at grade level, located not more than 6½ feet (2.0 m) above grade.

Must be GFCI-protected , listed as Weather-Resistant (WR) , and equipped with an extra-duty while-in-use cover .

Hallways & Foyers (NEC 210.52(H) & 210.52(I))

Hallways (210.52(H)): Hallways measuring 10 feet (3.0 m) or more in length require at least one receptacle outlet. Length is measured along the centerline of the hallway without passing through a doorway.

Foyers (210.52(I)): Foyers with an architectural floor area greater than 60 square feet (5.6 m²) must have at least one receptacle on any unbroken wall space that is 3 feet (900 mm) or wider .

Attached Garages (NEC 210.11(C)(4) & 210.52(G))

At least one dedicated 20-ampere branch circuit must be installed to supply garage receptacles.

At least one receptacle outlet must be installed in each vehicle bay , mounted not higher than 5.5 feet above the floor.

5. Comprehensive Summary Table: Dwelling Unit Circuits & Spacing

Location / Equipment Minimum Circuit Rating Conductor Size Max. Spacing / Location Rule GFCI Protected? AFCI Protected?

General Habitable Walls 15A or 20A 14 or 12 AWG 12 ft between outlets (6 ft to door/corner) No (unless within 6 ft of sink) Yes (NEC 210.12(B))

Kitchen Countertops 20A (SABC) 12 AWG Cu 4 ft between outlets (2 ft from edge) Yes (NEC 210.8(A)(6)) Yes (NEC 210.12(B))

Bathroom Basins 20A (Dedicated) 12 AWG Cu Within 36 in of basin edge Yes (NEC 210.8(A)(1)) No

Laundry Equipment 20A (Dedicated) 12 AWG Cu Within 6 ft of washing machine Yes (NEC 210.8(A)(11)) Yes (NEC 210.12(B))

  • Outdoor Front / Back 15A or 20A 14 or 12 AWG Front and back, max 6½ ft above grade Yes (NEC 210.8(A)(3)) No
  • Hallways 15A or 20A 14 or 12 AWG At least one if length is 10 ft or longer No Yes (NEC 210.12(B))
  • Attached Garage Bays 20A (Dedicated) 12 AWG Cu At least one outlet per vehicle bay Yes (NEC 210.8(A)(2)) No
  • 6. Required Lighting Outlets (NEC 210.70(A))

Adequate illumination controlled by convenient wall switches is essential for personal safety and egress. NEC 210.70(A) sets forth lighting requirements for dwelling units:

Habitable Rooms (NEC 210.70(A)(1))

At least one wall switch-controlled lighting outlet must be installed in every habitable room, kitchen, and bathroom.

Switched Receptacle Exception: In habitable rooms other than kitchens and bathrooms, one or more receptacles controlled by a wall switch are permitted in lieu of a permanent lighting outlet (e.g., a wall switch controlling a floor lamp in a bedroom or living room).

Stairways & Three-Way Switches (NEC 210.70(A)(2)(3))

Where an interior stairway has six or more risers , a wall switch must be located at each floor level and landing that includes an entryway to control the stairway lighting outlet. This requires 3-way or 4-way switching so occupants never have to traverse stairs in darkness.

Additional Required Locations (NEC 210.70(A)(2))

Wall switch-controlled lighting outlets are required in:

  • Hallways and Stairways
  • Attached Garages & Detached Garages with Electric Power

Exterior Entrances & Exits: Lighting outlet controlled by a wall switch must be installed on the exterior of all outdoor entrances with grade-level access (a garage vehicle door does not count as an outdoor entrance requiring an exterior luminaire).

Equipment Spaces: Attics, Basements, & Crawl Spaces (NEC 210.70(A)(3))

Where attics, underfloor spaces, utility rooms, and basements contain equipment requiring servicing (such as air handlers, heat pumps, furnaces, or water heaters):

At least one lighting outlet containing a switch or controlled by a wall switch must be installed.

The switch must be located at the entry point to the space.

The lighting outlet must be positioned at or near the equipment to illuminate servicing tasks.