Study guide
3.2 Psychrometric Chart Navigation, Air Properties & Core HVAC Processes
Kentucky HVAC Contractor License Master HVAC
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Kentucky Statutes, Regulations & Licensing
1.1 Kentucky HVAC Licensing & DHBC Regulatory Framework 1.2 Permits, Inspections & DHBC Code Enforcement 1.3 Contractor Responsibilities, Supervision & Professional Ethics
2 Chapter 2: Kentucky Business Management & Construction Law
2.1 Business Organization, Licensing & State/Local Taxes 2.2 Contracts, Estimating & Project Management 2.3 Kentucky Lien Law, Labor Standards & Workers' Compensation 2.4 Construction Plan Reading, Mechanical Blueprints & Specifications
3 Chapter 3: Thermodynamics, Psychrometrics & Load Sizing
3.1 Principles of Thermodynamics, Heat Transfer & Airflow Formulas 3.2 Psychrometric Chart Navigation, Air Properties & Core HVAC Processes 3.3 ACCA Manual J & Manual S Load Calculations and Equipment Selection
4 Chapter 4: Refrigeration Cycle & System Components
4.1 Vapor-Compression Refrigeration Cycle, P-H Diagrams & System Diagnostics 4.2 Compressor Technologies, Compression Ratios & Refrigerant Metering Devices 4.3 Evaporators, Condensers & Refrigeration System Accessories
5 Chapter 5: Heating Systems, Combustion & Heat Pumps
5.1 Gas Furnaces, Combustion Chemistry & Ignition Diagnostics 5.2 Fuel Oil Heating Systems & Electric Resistance Heating 5.3 Heat Pumps, Reverse-Cycle Operation & Defrost Controls
6 Chapter 6: Fuel Gas Piping & Combustion Air
6.1 Fuel Gas Piping Materials, Sizing & Installation 6.2 Combustion Air Sizing Methods & Outdoor Air Calculations
7 Chapter 7: Appliance Venting, Chimneys & Mechanical Exhaust
7.1 Appliance Venting Categories & Vent Piping Materials 7.2 Vent Sizing Tables, Chimney Draft Principles & Terminations 7.3 Mechanical Exhaust Systems, Duct Rules & Makeup Air (IMC Chapters 4 & 5)
8 Chapter 8: Duct Design, Air Distribution & Hydronics
8.1 ACCA Manual D Duct Sizing, Static Pressure & SMACNA Installation Standards 8.2 Air Distribution Devices, Noise Criteria, Filtration & Airflow Balancing 8.3 Hydronic Piping Systems, Circulator Sizing, Expansion Tanks & Safety Controls
9 Chapter 9: Electrical Power, Motors & Control Diagnostics
9.1 Electrical Fundamentals, Power Distribution & Circuit Sizing 9.2 Electric Motor Types, Capacitors & Starting Components 9.3 24VAC Control Circuits, Thermostats & Diagnostic Troubleshooting
10 Chapter 10: Refrigerant Management, Safety & Maintenance Operations
10.1 EPA Section 608, AIM Act & A2L Refrigerant Management 10.2 Jobsite Safety, OSHA Standards & Personal Protective Equipment 10.3 Preventive Maintenance Programs & Seasonal Service Operations
3.2 Psychrometric Chart Navigation, Air Properties & Core HVAC Processes
Key Takeaways Explain This Topic AI
The psychrometric chart graphically correlates seven fundamental thermodynamic properties of moist air at standard sea-level barometric pressure (29.921 in. Hg / 14.696 psia).
Knowing any two independent thermodynamic air properties completely fixes the state point, enabling all other five properties to be read directly from the chart.
The six fundamental air conditioning processes correspond to specific directional pathways across the psychrometric chart, including sensible heating/cooling, humidification/dehumidification, and cooling with dehumidification.
Evaporative cooling (adiabatic saturation) follows lines of constant wet-bulb temperature and constant enthalpy, trading sensible heat for latent heat without altering total heat content.
Mixed air calculations use linear weighted averages of mass and enthalpy to determine mixed dry-bulb temperature, enthalpy, and humidity ratio based on the outdoor air fraction.
Last updated: August 2026
Psychrometric Chart Navigation, Air Properties & Core HVAC Processes
Psychrometrics is the study of thermodynamic properties of gas-vapor mixtures, specifically moist atmospheric air (a mixture of dry air and water vapor). For HVAC contractors, the psychrometric chart is an indispensable diagnostic and engineering tool used to evaluate cooling coil performance, dehumidification capability, economizer operation, and building ventilation mixing.
1. The Seven Fundamental Properties of Moist Air
At standard atmospheric pressure (29.921 in. Hg / 14.696 psia at sea level), the state of moist air is fully defined by identifying any two independent thermodynamic properties . Once that "state point" is located on the chart, the remaining five properties can be read directly. +-----------------------------------------------------------------------------------------+
- | THE SEVEN MOIST AIR PROPERTIES SUMMARY |
- | |
- | 1. DRY-BULB TEMPERATURE (T_db) --> True kinetic temperature; vertical lines (°F) |
- | 2. WET-BULB TEMPERATURE (T_wb) --> Evaporative cooling limit; slanted lines (°F) |
- | 3. DEW-POINT TEMPERATURE (T_dp) --> Condensation threshold; horizontal lines (°F) |
- | 4. RELATIVE HUMIDITY (% RH) --> Moisture saturation fraction; curved lines (%) |
- | 5. HUMIDITY RATIO (W) --> Absolute moisture mass; grains/lb or lb/lb |
- | 6. SPECIFIC VOLUME (v) --> Inverse density; steep diagonal lines (ft³/lb) |
- | 7. ENTHALPY (h) --> Total thermal energy; outer diagonal scale (BTU/lb) |
- +-----------------------------------------------------------------------------------------+
- Detailed Engineering Analysis of Properties
Dry-Bulb Temperature (T_db):
The sensible temperature of the air measured by an ordinary thermometer shielded from direct thermal radiation.
Chart Representation: Uniform vertical lines extending from the bottom horizontal axis (°F).
Wet-Bulb Temperature (T_wb):
The lowest temperature air can reach through adiabatic evaporation of water into the airstream. Measured by a thermometer whose bulb is covered in a water-saturated cotton wick exposed to rapid air velocity (~900 ft/min).
Chart Representation: Diagonally sloping lines running from upper-left (saturation curve) downward to the bottom right.
Dew-Point Temperature (T_dp):
The temperature to which air must be cooled at constant barometric pressure and moisture content to become completely saturated (100% RH), initiating water vapor condensation (dew formation).
Chart Representation: Horizontal lines extending left to the saturation curve.
Relative Humidity (% RH):
The ratio of the actual partial water vapor pressure (p_w) in the air to the saturation vapor pressure (p_ws) of water at the same dry-bulb temperature, expressed as a percentage: RH = (p_w / p_ws) × 100% .
Chart Representation: Distinct curved lines radiating from lower-left to upper-right. The outermost curved boundary represents 100% RH (the Saturation Curve) , where T_db = T_wb = T_dp .
Humidity Ratio / Specific Humidity (W):
The actual mass of water vapor present per unit mass of bone-dry air. Expressed in grains of moisture per pound of dry air (7,000 grains = 1.0 lb) or pounds of water per pound of dry air.
Chart Representation: Horizontal lines read on the far-right vertical axis.
Specific Volume (v):
The volume occupied by one pound of dry air plus its associated water vapor. Specific volume is the reciprocal of air density (v = 1 / ρ).
Chart Representation: Steeply angled lines (steeper than wet-bulb lines), typically ranging from 12.5 to 15.0 ft³/lb dry air.
Enthalpy (h):
The total thermal energy content of moist air per unit mass, combining sensible heat (air and vapor temperature) and latent heat (vaporization energy). Expressed in BTUs per pound of dry air relative to a 0°F dry air baseline.
Chart Representation: Read on the diagonal scale positioned outside the saturation curve, aligning closely with wet-bulb lines.
- Moist Air Property Unit of Measurement Orientation on Standard Chart Primary HVAC Application
- Dry-Bulb (T_db) Degrees Fahrenheit (°F) Vertical lines Thermostat control, sensible heating/cooling loads
Wet-Bulb (T_wb) Degrees Fahrenheit (°F) Slanted lines (down to right) Cooling tower & evaporative coil sizing, heat pump defrost
Dew-Point (T_dp) Degrees Fahrenheit (°F) Horizontal lines Duct condensation prevention, coil dehumidification limit
Relative Humidity Percentage (%) Curved lines (0% to 100%) Indoor comfort control (30%–60%), mold prevention
Humidity Ratio (W) Grains/lb dry air Horizontal lines to right axis Latent load calculation, dehumidifier sizing
- Specific Volume (v) ft³/lb dry air Steep diagonal lines Fan mass flow rate and duct velocity sizing
- Enthalpy (h) BTU/lb dry air Slanted lines outside curve Total coil capacity, economizer changeover control
- 2. The Core Air Conditioning Processes
Thermodynamic processes alter the temperature and moisture state of air. On a psychrometric chart, each process forms a distinct vector path: +-----------------------------------------------------------------------------------------+
- | PSYCHROMETRIC PROCESS DIRECTIONAL VECTOR MAP |
- | |
- | Humidification |
- | ^ |
- | | |
- | Evaporative Cooling | Heating & Humidification |
- | (Constant Enthalpy) | |
- | \ | / |
- | \ | / |
- | Sensible Cooling <----------------+----------------> Sensible Heating |
- | (Constant Moisture) | (Constant Moisture) |
- | / | \ |
- | / | \ |
- | Cooling & | Chemical Dehumidification |
- | Dehumidification | (Desiccant) |
- | v |
- | Dehumidification |
- +-----------------------------------------------------------------------------------------+
- 1. Sensible Heating (Horizontal Right Vector)
Mechanism: Air passes across a hot heating coil or furnace heat exchanger with no moisture added.
Thermodynamic Impact: T_db increases, Enthalpy (h) increases, Humidity Ratio (W) remains constant, Dew-Point (T_dp) remains constant, Relative Humidity (% RH) decreases.
2. Sensible Cooling (Horizontal Left Vector)
Mechanism: Air passes across a cooling surface whose surface temperature is above the dew-point temperature of the entering air (no condensation occurs).
Thermodynamic Impact: T_db decreases, Enthalpy (h) decreases, Humidity Ratio (W) remains constant, Dew-Point (T_dp) remains constant, Relative Humidity (% RH) increases.
3. Cooling with Dehumidification (Down-and-Left Vector)
Mechanism: Standard direct-expansion (DX) or chilled water cooling coil operation. Air passes across a coil whose surface temperature ( Apparatus Dew Point / ADP ) is below the dew point of entering air. Water vapor condenses out of the airstream onto the coil fins and drains away.
Thermodynamic Impact: T_db decreases, T_wb decreases, T_dp decreases, Humidity Ratio (W) decreases, Enthalpy (h) decreases, Relative Humidity increases (typically leaving at 90%–95% RH).
Coil Bypass Factor (BF): The percentage of air that passes through the coil fins without contacting the cold surface. Modern residential coils have a bypass factor between 0.05 and 0.15 (5% to 15%).
4. Humidification (Vertical Upward Vector)
Mechanism: Direct steam injection into the airstream.
Thermodynamic Impact: Humidity Ratio (W) increases, Dew-Point (T_dp) increases, Relative Humidity increases, T_db remains nearly constant.
5. Heating and Humidification (Up-and-Right Vector)
Mechanism: Winter conditioned air passing through a warm air furnace and an active steam/bypass humidifier.
Thermodynamic Impact: T_db increases, W increases, Enthalpy (h) increases significantly.
6. Evaporative Cooling / Adiabatic Saturation (Up-and-Left Along Constant WB)
Mechanism: Direct evaporative cooler (swamp cooler). Water evaporates into unsaturated air with no external heat added or removed (adiabatic).
Thermodynamic Impact: Sensible heat transforms into latent heat of vaporization. T_db drops significantly, Humidity Ratio (W) rises, % RH rises, while Wet-Bulb Temperature (T_wb) and Enthalpy (h) remain constant .
3. Mixed Air Calculations (Ventilation & Economizers)
Commercial and residential systems frequently mix two airstreams: Return Air (RA) from the conditioned building and Outdoor Air (OA) for ventilation or free economizer cooling. +-----------------------------------------------------------------------------------------+
- | AIR MIXING CONSERVATION DIAGRAM |
- | |
- | Return Air (RA): CFM_RA, T_RA, W_RA, h_RA |
- | ===============================================\ |
- | +===> Mixed Air (MA): |
- | ===============================================/ CFM_total, T_MA, W_MA, h_MA |
- | Outdoor Air (OA): CFM_OA, T_OA, W_OA, h_OA |
- +-----------------------------------------------------------------------------------------+
- Governing Mathematical Formulas for Air Mixing
- Based on the conservation of mass and energy: Total Airflow: CFM_total = CFM_RA + CFM_OA
Mixed Air Dry-Bulb Temperature (T_MA):
- T_MA = ( (CFM_RA × T_RA) + (CFM_OA × T_OA) ) / CFM_total
- T_MA = T_RA + [ (CFM_OA / CFM_total) × (T_OA - T_RA) ]
Mixed Air Enthalpy (h_MA):
h_MA = ( (CFM_RA × h_RA) + (CFM_OA × h_OA) ) / CFM_total
Mixed Air Humidity Ratio (W_MA):
W_MA = ( (CFM_RA × W_RA) + (CFM_OA × W_OA) ) / CFM_total
Percentage Outdoor Air (% OA):
- % OA = ( (T_MA - T_RA) / (T_OA - T_RA) ) × 100%
- 4. Step-by-Step Worked Air Mixing Calculation Example
Scenario: A rooftop commercial packaged unit in Louisville, KY operates with an outdoor air economizer delivering a total airflow of 4,000 CFM. The system settings and psychrometric readings are:
Return Air (RA): 3,000 CFM (75% of total airflow), 76°F DB, 63°F WB, Enthalpy h_RA = 28.5 BTU/lb , Moisture W_RA = 65 grains/lb .
Outdoor Air (OA): 1,000 CFM (25% of total airflow), 92°F DB, 76°F WB, Enthalpy h_OA = 39.5 BTU/lb , Moisture W_OA = 118 grains/lb . Step 1: Calculate Mixed Air Dry-Bulb Temperature (T_MA)
- T_MA = [ (3,000 CFM × 76°F) + (1,000 CFM × 92°F) ] / 4,000 CFM
- T_MA = [ 228,000 + 92,000 ] / 4,000
- T_MA = 320,000 / 4,000 = 80.0°F DB
- Step 2: Calculate Mixed Air Enthalpy (h_MA)
- h_MA = [ (3,000 CFM × 28.5 BTU/lb) + (1,000 CFM × 39.5 BTU/lb) ] / 4,000 CFM
- h_MA = [ 85,500 + 39,500 ] / 4,000
- h_MA = 125,000 / 4,000 = 31.25 BTU/lb
- Step 3: Calculate Mixed Air Humidity Ratio (W_MA)
- W_MA = [ (3,000 CFM × 65 gr/lb) + (1,000 CFM × 118 gr/lb) ] / 4,000 CFM
- W_MA = [ 195,000 + 118,000 ] / 4,000
- W_MA = 313,000 / 4,000 = 78.25 grains/lb dry air
Step 4: Calculate Total Required Coil Cooling Load
If the evaporator coil cools this mixed airstream down to 55°F DB leaving condition with enthalpy h_leaving = 23.0 BTU/lb:
- Δh_coil = 31.25 BTU/lb - 23.0 BTU/lb = 8.25 BTU/lb
- Qt = 4.5 × CFM_total × Δh_coil
- Qt = 4.5 × 4,000 CFM × 8.25 BTU/lb = 148,500 BTU/hr
- Total Tonnage = 148,500 / 12,000 = 12.375 Tons