Study guide
4.2 Reroofing Rules (IBC 1512 / IRC R908): Roof Replacement vs. Roof Recover, the Two-Layer Limit & Tear-Off Triggers
Louisiana Residential Roofing Contractor Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Louisiana Licensing Law & Act 422 Regulatory Framework
1.1 Act 422 (2025): The Residential Roofing Classification, the $7,500 Threshold & Licensing Requirements 1.2 Act 239 (2025) Roof Permits & Inspections, Permit-Related Violations & Louisiana's Construction Code 1.3 LSLBC Enforcement: Violations, Cease-and-Desist Orders, Civil Fines & Criminal Penalties
2 Chapter 2: Louisiana Business Law, Contracts & Liens
2.1 Louisiana Private Works Act (La. R.S. 9:4801 et seq.): Privileges, Notices of Contract & Termination, and Lien Deadlines 2.2 Residential Roofing Contracts: Required Contents (R.S. 37:2159) & Property-Insurance Claim Rules (R.S. 37:2159.1) 2.3 Contractor Insurance (Liability & Workers' Compensation), the Statutory Employer Rule & Business Records
3 Chapter 3: Roofing Estimating, Plan Reading & Mathematics
3.1 Architectural Roof Plans, Symbols, Dimensions & Structural Pitch Calculations 3.2 Surface Area Calculations, Roofing Squares, Pitch Multipliers & Slope Formulas 3.3 Material Takeoff, Wastage Factors (Hips, Valleys, Rakes), and Jobsite Cost Estimating
4 Chapter 4: Roof Deck Preparation, Substrates & Re-Roofing Codes
4.1 Roof Deck Substrates (Plywood, OSB, Wood Board) & Structural Inspection Criteria 4.2 Reroofing Rules (IBC 1512 / IRC R908): Roof Replacement vs. Roof Recover, the Two-Layer Limit & Tear-Off Triggers 4.3 Deck Fastening, Nail Patterns, Damaged Sheathing Replacement & Clean Substrate Preparation
5 Chapter 5: Hurricane-Resistant Roofing, Wind Codes & FORTIFIED Standards
5.1 Louisiana Wind Speeds, Exposure, Wind-Borne Debris Regions & Roof Uplift Zones (IBC Chapter 16 / ASCE 7) 5.2 High-Wind Underlayment Rules (IBC Table 1507.1.1) & Sealed Roof Deck Options (Taped Seams, Two Layers, Full Self-Adhered) 5.3 IBHS FORTIFIED Roof (2025 Standard), the Louisiana Fortify Homes Program & Louisiana FORTIFIED Incentives 5.4 High-Wind Fastening Protocols: 6-Nail Shingle Patterns, Ring-Shank Nails & ASTM D3161/D7158 Wind Ratings
6 Chapter 6: Asphalt Shingles & Steep-Slope Assemblies
6.1 Asphalt Shingle Types (3-Tab vs. Laminated Architectural), ASTM Classifications & Thermal Behavior 6.2 Underlayment Specifications: Felt vs. Synthetic Underlayments & Self-Adhering High-Temperature Membranes 6.3 Shingle Application Mechanics: Starter Courses, Offsets, Fastener Placement & Wind Sealant Activation 6.4 Valley Construction Assemblies (Open Metal, Woven, Closed-Cut) & Ridge / Hip Cap Installations
7 Chapter 7: Metal, Tile, Slate & Wood Steep-Slope Systems
7.1 Metal Roof Panels & Metal Roof Shingles: Standing Seam, Exposed Fasteners, Minimum Slopes & Thermal Movement 7.2 Concrete & Clay Tile Roof Systems: Battens, Direct-to-Deck, Wind Uplift Resistance & Foam/Mortar Adhesion 7.3 Natural Slate & Synthetic Tile Roofing: Installation Fundamentals, Headlap & Fastening 7.4 Wood Shingles & Wood Shakes (IBC 1507.8–1507.9): Grades, Slopes, Sheathing, Exposure, Spacing & Fasteners
8 Chapter 8: Low-Slope Membranes & Built-Up Roofing (BUR)
8.1 Built-Up Roofing (BUR) Systems: Asphalt vs. Coal Tar Pitch, Organic/Glass Felts & Surfacings 8.2 Polymer-Modified Bitumen Systems: SBS vs. APP, Torched, Hot-Mopped, Cold-Adhesive & Self-Adhered Sheets 8.3 Single-Ply Roofing Membranes: TPO, PVC, and EPDM (Attachment Methods, Seam Welding & Ballast) 8.4 Low-Slope Rigid Insulation, Cover Boards, Vapor Retarders & Thermal Barriers
9 Chapter 9: Flashing, Penetrations & Roof Ventilation
9.1 Edge Metal & Drip Edge: Code Rules (IBC 1507.2.8.3 / IRC R905.2.8.5), FORTIFIED Upgrades & ES-1 Edge Securement 9.2 Step Flashing, Counterflashing, Chimney Crickets & Reglet Details 9.3 Plumbing Vents, Mechanical Exhausts, Skylight Curbs & Roof Penetration Seals 9.4 Attic Ventilation: Net Free Ventilating Area (1/150 vs. 1/300 Rule, IBC 1202.2 / IRC R806), Balanced Airflow & Unvented Attics
10 Chapter 10: Roof Drainage, Maintenance & Emergency Repairs
10.1 Roof Drainage Design: Primary Drains, Secondary Overflow Scuppers & Sizing Calculations 10.2 Gutters, Downspouts, Splash Blocks & Stormwater Runoff Management 10.3 Post-Storm Emergency Tarping, Temporary Shoring, Moisture Assessment & Insurance Scope Documentation
11 Chapter 11: OSHA Safety, Fall Protection & Jobsite Environmental Controls
11.1 OSHA 29 CFR 1926 Subpart M: Fall Protection Systems (Guardrails, Safety Nets, PFAS, Warning Lines & Monitors) 11.2 Ladder & Scaffolding Safety (29 CFR 1926 Subpart L & X, 4:1 Extension Rule, Tie-Off & Pitch) 11.3 PPE, Tool Safety, Hot Kettle/Torch Safety & Hazardous Material Communication (Lead, Asbestos, Silica) 11.4 Heat Illness Prevention & Louisiana High-Humidity Environmental Field Controls
4.2 Reroofing Rules (IBC 1512 / IRC R908): Roof Replacement vs. Roof Recover, the Two-Layer Limit & Tear-Off Triggers
Key Takeaways Explain This Topic AI
Roof replacement means removing all existing layers of roof covering down to the roof deck (IBC 1512.2; IRC R908.3).
A recover is not permitted where the existing roof has two or more applications of any roof covering (IBC 1512.2.1.1; IRC R908.3.1.1).
A recover is also prohibited over a water-soaked or deteriorated roof, or over existing slate, clay, cement, or asbestos-cement tile.
Metal panel, metal shingle, and concrete or clay tile coverings may go over existing wood shakes if any combustible concealed space is covered per IBC 1512.3.
A shingle overlay adds roughly 2.5 to 3.5 psf of dead load; the IEBC requires framing whose design dead load rises more than 5 percent to be shown adequate or strengthened.
Last updated: September 2026
Re-Roofing Regulations under LSUCC and IRC Section R908
Most roofing work in Louisiana is reroofing, driven by weathering, ultraviolet exposure, and storms. The state's uniform construction code covers it through IRC Section R908 for one- and two-family dwellings and IBC Section 1512 for other buildings. The IEBC 2021, Section 705, repeats the same reroofing rules for existing buildings. The PSI exam's code is the 2021 IBC , so tab Section 1512 . The IRC wording is nearly identical.
1. Regulatory Definitions: Roof Replacement vs. Roof Recover
The IBC and IRC define the terms this way:
Re-Roofing: The overarching term encompassing any process of recovering or replacing an existing roof covering.
Roof Replacement (Tear-Off): Removing all existing layers of roof coverings down to the roof deck (IBC 1512.2; IRC R908.3). One exception: an existing adhered ice barrier membrane may stay and be covered with a new ice barrier layer.
Roof Recover (Overlay): The process of installing an additional roof covering directly over an existing roof covering without removing the existing covering down to the structural deck.
2. The Two-Layer Maximum Rule
The main limit in steep-slope reroofing is the two-layer rule in IBC 1512.2.1.1 (IRC R908.3.1.1):
A roof recover shall not be permitted where the existing roof has two or more applications of any type of roof covering.
A third layer is never allowed. If a home already has two layers of shingles, whether three-tab, organic felt, or laminated, both must come off down to the deck . Installing a third layer is a code violation the inspector will fail. It usually voids the shingle warranty. It can also be treated as an LSLBC violation for disregarding code and failing required inspections.
3. When a Recover Is Allowed and When It Is Prohibited
IBC 1512.2.1 permits a new covering over an existing one in these cases:
The new covering is installed per the manufacturer's approved instructions , which must allow a recover.
The system is a complete and separate roofing system , such as standing-seam metal panels that carry roof loads directly to the structure.
Metal panels, metal shingles, or concrete or clay tile are installed over existing wood shakes in accordance with Section 1512.3.
A new protective coating is applied over certain existing coatings, metal panels, built-up roofs, SPF, metal shingles, roll roofing, modified bitumen, or single-ply.
IBC 1512.2.1.1 (IRC R908.3.1.1) prohibits a recover in three situations:
the existing roof or roof covering is water soaked or has deteriorated to the point that it is not adequate as a base for more roofing;
the existing roof covering is slate, clay, cement, or asbestos-cement tile ;
the existing roof has two or more applications of any roof covering.
The field conditions below show how those prohibitions play out.
A. Deteriorated, Water-Soaked, or Structurally Unsound Substrate
If the existing covering or the deck under it is water-soaked, rotted, spongy, or deteriorated, it is not an adequate base, and the code prohibits a recover. Fasteners cannot achieve proper withdrawal resistance in rotted wood, and trapped moisture sealed beneath a new layer will accelerate fungal decay, rot out rafters, and promote hazardous toxic mold growth within the attic assembly.
B. Existing Coverings the Code Will Not Let You Cover
Slate: cannot be nailed through without shattering and is too heavy to leave in place.
Clay or cement (concrete) tile: an uneven, heavy base that cannot support a new covering.
Asbestos-cement tile or shingles: also a regulated material. Removal is asbestos work under OSHA 29 CFR 1926.1101 (Chapter 11).
Wood shakes and wood shingles are handled differently. The code does not list them as a prohibition. It lets metal panels, metal shingles, and concrete or clay tile go over existing wood shakes. Where covering wood shingles or shakes creates a combustible concealed space , the whole existing surface must first be covered with gypsum board, mineral fiber, glass fiber, or another approved material (IBC 1512.3). In practice, most asphalt-shingle manufacturers require wood roofs to be torn off, so the manufacturer's instructions usually decide.
C. Severe Shingle Distortion (Curling, Cupping, Blistering)
Badly curled, cupped, fish-mouthed, or blistered shingles are a poor base, and most manufacturers' recover instructions exclude them. Installing new shingles over an irregular surface creates severe "bridging," where the new shingles span over voids without resting flat on the deck. Bridged shingles crack under foot traffic, cannot activate their thermal sealant strips, and blow off rapidly in moderate wind.
D. Post-Hurricane Wind Uplift and Hail Failure
After a storm, a roof with peeled shingles, breached underlayment, or hail-fractured mats may have wet or damaged decking hidden underneath. Tearing off lets you find and fix that damage. A wet or deteriorated existing roof also falls under the code's water-soaked or deteriorated prohibition.
4. Structural Dead Load Dynamics: The Engineering Reality of Overlays
One of the most dangerous fallacies in roofing is treating an overlay purely as a labor-saving convenience while ignoring structural physics. Every layer of roofing added to a structure increases its permanent dead load ( D D D ).
Calculating Roofing Cladding Dead Load
- Roofing Assembly Material Typical Weight per Square (100 sq ft) Dead Load in Pounds per Square Foot (psf)
- Single Layer #15 Felt + 3-Tab Asphalt Shingles 220 to 250 lbs 2.2 to 2.5 psf
- Single Layer Synthetic + Standard Architectural Laminate 280 to 350 lbs 2.8 to 3.5 psf
- Heavyweight / Luxury Designer Shingles 400 to 450 lbs 4.0 to 4.5 psf
- Two Layers of Asphalt Shingles (Combined Weight) 500 to 800 lbs 5.0 to 8.0 psf
- Concrete S-Tile or Barrel Tile 900 to 1,200 lbs 9.0 to 12.0 psf
- Natural Roofing Slate (3/16" to 1/4" thickness) 750 to 1,000 lbs 7.5 to 10.0 psf
- Structural Implications for Louisiana Housing Stock
Many older Louisiana homes have light rafters, such as 2x4s or 2x6s at 24 inches on center, with little reserve capacity. For perspective, the IRC's rafter span tables are built on a design dead load of either 10 or 20 psf, and that load covers the rafters, sheathing, and roofing together.
An architectural overlay (about 3.5 psf) on an existing layer (about 2.5 psf) puts roughly 6 psf of shingles alone on the framing. That can use up most of a 10-psf design allowance.
The IEBC 2021 (Section 503.3) requires any existing gravity-load element whose design dead load rises more than 5 percent because of an alteration to be replaced or altered to carry IBC loads, unless an exception applies. One exception covers small Group R buildings that meet conventional light-frame or IRC provisions. When weight goes up, verify the framing.
Consequences of Excessive Dead Load: Under sustained summer heat and humidity, wood rafters undergo creep (slow, irreversible structural deflection). This causes sagging ridgelines, dipping roof planes, jammed interior doors, cracked ceiling drywall, and catastrophic structural failure when combined with winter ice/sleet loads or hurricane wind uplift pressures.
Loading diagram... IBC 1512 / IRC R908 Reroofing Decision Tree
5. High-Wind and Hurricane Risks of Overlays in Louisiana
While an overlay may be legally permissible under the narrow exception of a single layer of sound asphalt shingles on an undamaged deck, roof recovery is widely condemned by building scientists, structural engineers, and professional roofing associations in Louisiana. Along the Gulf Coast, installing a roof overlay introduces five severe failure mechanisms:
Inability to Inspect the Structural Deck: An overlay leaves the original wood sheathing completely blind. Active termite infestations, dry rot, rusted fasteners, and delaminated plywood remain hidden. New fasteners driven into rotted sheathing have zero holding power, turning the new roof into an airborne projectile during a hurricane.
No Sealed Roof Deck: FORTIFIED Roof requires a sealed roof deck, and in high-wind areas the IBC offers taped deck seams as an underlayment option (Chapter 5). A recover makes sealing the deck impossible, so the roof loses its second line of defense if the shingles blow off.
Poorer Fastening: Nails for a recover must be long enough to pass through both layers and still penetrate 3/4 inch into the deck, or through it (IBC 1507.2.5). Old, uneven shingles make nails tilt and seat inconsistently. Crooked, underdriven, or overdriven nails reduce the shingles' uplift resistance.
Thermal Blistering and Shortened Shingle Life: In Louisiana's extreme summer climate, where roof deck temperatures reach 150°F to 170°F, an overlay acts as a massive heat sink. The double layer traps radiant heat, prevents thermal dissipation through the attic, and cooks the asphalt oils out of the new shingles, leading to premature granule loss, blistering, and severe embrittlement in as little as 5 to 7 years.
Warranty Limits: Manufacturers often restrict or reduce enhanced warranties, including higher wind warranties, for shingles installed over an existing roof. Read the specific warranty before quoting a recover.
6. Permitting, Inspections, and Act 239 Enforcement Milestones
Act 239 of 2025 requires parishes and municipalities that issue permits to permit and inspect reroofing (Section 1.2). Inspection stages vary by jurisdiction.
Typical Inspection Milestones
Permit Application Phase: The licensed contractor must submit a detailed permit application specifying: building address, structural square footage, existing roof assembly, proposed scope of work (complete tear-off vs. recover), manufacturer specifications, underlayment type, and fastener schedule (including high-wind compliance).
In-Progress / Deck Inspection: Where the jurisdiction requires it, the deck is inspected after tear-off and before underlayment. The inspector looks for:
Replacement of all rotted, delaminated, or damaged sheathing.
Sheathing fastening to the applicable schedule. In Louisiana, where wind design is required, the state's IRC amendment calls for RSRS-01 ring-shank nails at 6 inches on center (Section 1.2).
Panel spacing and edge support (clips or blocking) where needed.
Final Roof Inspection: After all underlayment, flashings, valley liners, shingles, and ventilation accessories are installed, the inspector verifies drip edge fastening, step flashing kickout angles, ridge cap fastening, and attic net free ventilating area.