Study guide
3.1 Scoping Site Analysis & Synthesizing Opportunities and Constraints
Landscape Architect Registration Examination L.A.R.E.
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Project Management, Legal Framework & Contracts
1.1 Professional Practice, Ethics & the HSW Mandate 1.2 Standard of Care, Responsible Charge & Sealing Documents 1.3 Professional Services Agreements & Contract Clauses 1.4 Fee Structures, Compensation Models & Billing 1.5 Project Scheduling, CPM & Budget Management 1.6 Risk Management, Professional Liability & Insurance
2 Chapter 2: Site Inventory, Surveying & Regulatory Framework
2.1 Boundary Surveys, Legal Descriptions & Survey Datums 2.2 Topographic Surveys, Easements & Encumbrances 2.3 Desktop Inventory, GIS Data & Field Reconnaissance 2.4 Policy Documents & Prior Planning Studies 2.5 Adjacent Land Use & Contextual Data Collection 2.6 Stakeholder Engagement & Public Participation 2.7 Zoning Frameworks, Dimensional Standards & FAR 2.8 Parking Standards, Buffer Yards & Zoning Relief 2.9 Clean Water Act Permitting & NEPA Review 2.10 ESA, Floodplain, Coastal & Historic Preservation Compliance
3 Chapter 3: Physical, Contextual & Environmental Site Analysis
3.1 Scoping Site Analysis & Synthesizing Opportunities and Constraints 3.2 Geotechnical Investigation & Soil Classification Systems 3.3 Problematic Soil Conditions & Agronomic Soil Quality 3.4 Topographic Interpretation & Slope Suitability 3.5 Watershed Mechanics, Stream Order & FEMA Flood Hazard Zones 3.6 Wetland Delineation, Classification & Riparian Buffers 3.7 Utility Analysis & Infrastructure Capacity 3.8 Visual Resource & Viewshed Analysis 3.9 Contextual Analysis: Appropriate Use & Future Development Impacts 3.10 Microclimates, Solar Orientation & Vegetation Analysis
4 Chapter 4: Stewardship, Climate Resiliency & Design Principles
4.1 SITES v2 & LEED Site Credit Rating Systems 4.2 Life-Cycle Assessment, Embodied Carbon & Ecosystem Services 4.3 Climate Resiliency, Adaptation & Urban Heat Island Mitigation 4.4 Environmental Justice & Social Equity in Site Design 4.5 Cultural Landscapes, Historic Preservation & Adaptive Reuse
5 Chapter 5: Master Planning, Programming & Land Use
5.1 Project Visioning, Goal Setting & Space Programming 5.2 Carrying Capacity Analysis & NRPA Park Classification Standards 5.3 Site Suitability Synthesis & Opportunities/Constraints Mapping 5.4 Land Use Allocation & Development Scenario Evaluation 5.5 Master Plan Deliverables & Design Guidelines 5.6 Capital Improvement Programming, Phasing & Implementation
6 Chapter 6: Schematic Design & Spatial Organization
6.1 Design Intent, Conceptual Diagrams & Form Generation 6.2 Basis of Design, Alternatives Evaluation & the Preferred Scheme 6.3 Spatial Hierarchy, Outdoor Rooms & Proportion 6.4 Pedestrian Circulation Networks & Environmental Wayfinding 6.5 ADA & PROWAG Accessible Route Design 6.6 Multimodal Transportation, Vehicular Circulation & Parking Layout
7 Chapter 7: Design Development, Materials & Planting Systems
7.1 Paving Systems: Rigid, Flexible & Unit Pavers 7.2 Retaining Walls, Earth Pressure & Wall Drainage 7.3 Wall System Selection, Fences, Screens & Gates 7.4 Site Furnishings: Selection, Materiality & Anchoring 7.5 Exterior Lighting, Photometrics, Dark Sky & Electrical Safety 7.6 Public Playground Safety: CPSC & ASTM Standards 7.7 Planting Design Principles & Ecological Matching 7.8 Water Conservation, Xeriscaping & Irrigation System Principles 7.9 Opinions of Probable Cost & Value Engineering
8 Chapter 8: Construction Drawings, Layout & Detailing
8.1 Drawing Set Hierarchy, Sheet Standards & Drafting Conventions 8.2 Interdisciplinary Coordination & QA/QC Review 8.3 Demolition Plans & Tree Protection Requirements 8.4 Site Preparation: Clearing, Grubbing, Topsoil & Utility Abandonment 8.5 Layout, Dimensioning & Materials Plans 8.6 Planting Plans, Plant Schedules & Installation Details 8.7 Technical Detailing: Pavements, Curbs & Joint Assemblies 8.8 Retaining Wall, Stair & Ramp Detailing Standards
9 Chapter 9: Construction Specifications & Bidding
9.1 CSI MasterFormat Divisions & SectionFormat Structure 9.2 Specification Writing Methods & the Drawings–Specifications Relationship 9.3 Project Manual, General Conditions & Front-End Documents 9.4 Bid Requirements, Bid Forms & Addenda Management 9.5 Pre-Bid Procedures, Bid Opening & Contractor Evaluation
10 Chapter 10: Construction Administration, Submittals & Changes
10.1 Pre-Construction Conference & Construction Administration Authority 10.2 Initial Decision Maker, Communication Protocols & Project Records 10.3 Submittals, Shop Drawings, Product Data & Samples 10.4 Requests for Information (RFIs) & Technical Clarifications 10.5 Change Orders, Construction Change Directives & Claims
11 Chapter 11: Field Observation, Quality Control & Close-Out
11.1 Field Observations, Site Reports & Non-Conforming Work 11.2 Quality Control, Material Testing & Inspections 11.3 Substantial Completion, Punch Lists & Retainage 11.4 Project Close-Out, Guarantees, Warranties & Final Acceptance
12 Chapter 12: Contour Interpretation, Grading & Earthwork Calculations
12.1 Contour Rules & Topographic Landform Interpretation 12.2 Spot Elevations & Contour Interpolation Calculations 12.3 Slope Formulas, Maximum Gradients & Cross Slopes 12.4 Earthwork Calculations: Average End Area & Grid Methods 12.5 Cut and Fill Balancing, Shrinkage, Swell & Mass Haul 12.6 Reviewing Grading Design: Error Detection & Constructability
13 Chapter 13: Stormwater Hydrology, Runoff & BMP Design
13.1 Hydrologic Cycle, Watershed Delineation & Time of Concentration 13.2 Peak Runoff Estimation: The Rational Method (Q = CiA) 13.3 NRCS Curve Number Method & Runoff Hydrographs 13.4 LID Principles, Water Quality Volume & Bioretention Design 13.5 Bioswales, Permeable Pavement, Green Roofs & Harvesting
14 Chapter 14: Site Drainage Systems, Hydraulics & Erosion Control
14.1 Open Channel Hydraulics, Manning’s Equation & Swale Design 14.2 Gutter Flow, Spread & Roadway Inlet Hydraulics 14.3 Subsurface Drainage, Catch Basins & Pipe Invert Calculations 14.4 Stormwater Storage: Detention, Retention & Water Quality Basins 14.5 Reviewing Drainage Plans & Evaluating Design Alternatives 14.6 Erosion Mechanics, RUSLE & the NPDES/SWPPP Framework 14.7 Erosion & Sediment Control BMPs, Basins & Site Stabilization
3.1 Scoping Site Analysis & Synthesizing Opportunities and Constraints
Key Takeaways Explain This Topic AI
Analysis scope is driven by the decisions the analysis must support, the regulatory triggers present on the site, and the consequence of being wrong, not by a standard checklist applied uniformly.
A screening-level analysis is appropriate where the answer is likely to be clear; an investigation-level analysis is required where a regulatory threshold, a life-safety consequence, or a large cost swing depends on the result.
Absolute constraints eliminate land from development entirely, while conditional constraints only increase cost or require mitigation; conflating the two produces either an unbuildable plan or an illegal one.
Opportunities and constraints mapping is a synthesis product, not an inventory product, and every polygon on it must trace to a specific analysis layer.
Analysis that does not change a design decision is wasted scope, so each proposed analysis should be justified by naming the decision it informs.
Last updated: September 2026
1. The Blueprint Task Nobody Plans For
Determine Appropriate Types of Analyses is an explicit task inside the Physical Analysis content area, which carries 39% of the Inventory, Analysis and Project Management section — the single heaviest content area in that exam section. It is tested because scoping errors are expensive in both directions: an under-scoped analysis produces a design that fails at permitting, and an over-scoped analysis burns fee on studies that never change a decision.
The governing question is always the same: what decision does this analysis inform, and what happens if the answer is wrong?
- 2. Three Drivers of Analysis Scope
- Driver 1: The decision to be supported
Each analysis exists to answer a design question. If no design question depends on it, it should not be in the scope.
- Design question Analysis required
- Can a building or structure be placed here? Geotechnical investigation, slope stability, floodplain
- Where does water go, and how much? Hydrologic analysis, watershed delineation, existing drainage
- Can these trees be saved? Vegetation inventory and tree condition assessment
- Is this land developable at all? Wetland delineation, floodway, protected species, contamination
- Will people be able to get here? Circulation and access analysis, transit and network connectivity
- What will it look like from off site? Visual resource and viewshed analysis
- Can the utilities serve it? Utility capacity and availability analysis
- Driver 2: Regulatory triggers present on the site
Certain site conditions convert an optional analysis into a mandatory one:
- Any mapped wetland, stream, or open water → wetland delineation and probable CWA Section 404 review
- Any FEMA Special Flood Hazard Area → floodplain and floodway analysis
- Any federal funding, permit, or land → NEPA review and Section 106 consultation
- Listed or candidate species habitat → ESA consultation
- One acre or more of land disturbance → NPDES Construction General Permit and SWPPP
Prior industrial or commercial use → Phase I Environmental Site Assessment , and a Phase II if recognized environmental conditions are identified
Driver 3: Consequence of error
Analysis depth scales with risk. The profession distinguishes two levels:
Screening level. Published, remotely sensed, or desktop data used to determine whether a condition is likely present. Examples: NRCS Web Soil Survey, National Wetlands Inventory, FEMA FIRM panel, published bearing capacity tables. Fast, cheap, and legally non-binding.
Investigation level. Site-specific, field-verified, professionally certified data. Examples: geotechnical boring log, jurisdictional wetland delineation, ALTA survey, Phase II soil sampling. Slow, expensive, and legally relied upon.
Exam rule: a screening product may be used to plan , but never to permit or to certify . An NWI polygon supports a preliminary layout; only a field delineation with a USACE jurisdictional determination supports a permit application.
3. Sequencing the Analyses
Analyses are not independent. Several must precede others because their outputs are inputs:
- Boundary and topographic survey — everything else registers to it
- Regulatory screening (flood, wetland, species, contamination) — defines what land is even in play
- Physical analyses (soils, slope, hydrology, vegetation, microclimate) — characterize the land that remains
- Systems analyses (utilities, circulation, visual) — characterize connections to context
- Synthesis — opportunities and constraints, then suitability
Running a costly geotechnical program before the wetland delineation is a classic sequencing error: borings placed inside a delineated wetland are wasted, and the drilling access itself may be an unpermitted disturbance.
4. Synthesizing Opportunities and Constraints
The synthesis product is not a stack of inventory maps. It is a single interpretive framework in which every polygon traces back to a specific analysis layer.
Constraint classification is the critical distinction:
Class Definition Examples Effect on plan
Absolute constraint Development is prohibited or physically impossible Regulatory floodway, jurisdictional wetland without a permit, recorded conservation easement, protected species habitat, slopes above the regulated threshold Land is removed from the development envelope
Conditional constraint Development is possible with added cost, mitigation, or engineering Expansive clay subgrade, 15–25% slope, high water table, poor soil bearing, utility easement Land remains in the envelope with a cost or design condition attached
Opportunity A condition that increases value if the design responds to it Mature canopy, southern exposure, long view corridor, existing stone wall, transit stop at the frontage, existing stormwater outfall Design should be organized to capture it
Treating a conditional constraint as absolute needlessly shrinks the buildable area and can make a viable project look infeasible. Treating an absolute constraint as conditional produces a plan that cannot be permitted.
Opportunities are analytically harder than constraints and are routinely under-developed. A constraint announces itself; an opportunity has to be recognized. The discipline is to walk each inventory layer a second time asking not "what does this prevent" but "what does this make possible here that would not be possible elsewhere."
5. Exam Traps & Pitfalls
Applying a uniform analysis checklist. Scope must be justified by the decisions and triggers actually present.
Using screening data to permit. NWI, Web Soil Survey, and FIRM panels plan; field delineations, borings, and surveys permit.
Conflating absolute and conditional constraints. Steep slope is usually conditional; regulatory floodway is absolute.
Producing an inventory stack and calling it a synthesis. Every synthesis polygon must be traceable to an analysis.
Sequencing expensive field work ahead of regulatory screening. Delineate before you drill.