Study guide

6.5 ADA & PROWAG Accessible Route Design

Landscape Architect Registration Examination L.A.R.E.

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Project Management, Legal Framework & Contracts

1.1 Professional Practice, Ethics & the HSW Mandate 1.2 Standard of Care, Responsible Charge & Sealing Documents 1.3 Professional Services Agreements & Contract Clauses 1.4 Fee Structures, Compensation Models & Billing 1.5 Project Scheduling, CPM & Budget Management 1.6 Risk Management, Professional Liability & Insurance

2 Chapter 2: Site Inventory, Surveying & Regulatory Framework

2.1 Boundary Surveys, Legal Descriptions & Survey Datums 2.2 Topographic Surveys, Easements & Encumbrances 2.3 Desktop Inventory, GIS Data & Field Reconnaissance 2.4 Policy Documents & Prior Planning Studies 2.5 Adjacent Land Use & Contextual Data Collection 2.6 Stakeholder Engagement & Public Participation 2.7 Zoning Frameworks, Dimensional Standards & FAR 2.8 Parking Standards, Buffer Yards & Zoning Relief 2.9 Clean Water Act Permitting & NEPA Review 2.10 ESA, Floodplain, Coastal & Historic Preservation Compliance

3 Chapter 3: Physical, Contextual & Environmental Site Analysis

3.1 Scoping Site Analysis & Synthesizing Opportunities and Constraints 3.2 Geotechnical Investigation & Soil Classification Systems 3.3 Problematic Soil Conditions & Agronomic Soil Quality 3.4 Topographic Interpretation & Slope Suitability 3.5 Watershed Mechanics, Stream Order & FEMA Flood Hazard Zones 3.6 Wetland Delineation, Classification & Riparian Buffers 3.7 Utility Analysis & Infrastructure Capacity 3.8 Visual Resource & Viewshed Analysis 3.9 Contextual Analysis: Appropriate Use & Future Development Impacts 3.10 Microclimates, Solar Orientation & Vegetation Analysis

4 Chapter 4: Stewardship, Climate Resiliency & Design Principles

4.1 SITES v2 & LEED Site Credit Rating Systems 4.2 Life-Cycle Assessment, Embodied Carbon & Ecosystem Services 4.3 Climate Resiliency, Adaptation & Urban Heat Island Mitigation 4.4 Environmental Justice & Social Equity in Site Design 4.5 Cultural Landscapes, Historic Preservation & Adaptive Reuse

5 Chapter 5: Master Planning, Programming & Land Use

5.1 Project Visioning, Goal Setting & Space Programming 5.2 Carrying Capacity Analysis & NRPA Park Classification Standards 5.3 Site Suitability Synthesis & Opportunities/Constraints Mapping 5.4 Land Use Allocation & Development Scenario Evaluation 5.5 Master Plan Deliverables & Design Guidelines 5.6 Capital Improvement Programming, Phasing & Implementation

6 Chapter 6: Schematic Design & Spatial Organization

6.1 Design Intent, Conceptual Diagrams & Form Generation 6.2 Basis of Design, Alternatives Evaluation & the Preferred Scheme 6.3 Spatial Hierarchy, Outdoor Rooms & Proportion 6.4 Pedestrian Circulation Networks & Environmental Wayfinding 6.5 ADA & PROWAG Accessible Route Design 6.6 Multimodal Transportation, Vehicular Circulation & Parking Layout

7 Chapter 7: Design Development, Materials & Planting Systems

7.1 Paving Systems: Rigid, Flexible & Unit Pavers 7.2 Retaining Walls, Earth Pressure & Wall Drainage 7.3 Wall System Selection, Fences, Screens & Gates 7.4 Site Furnishings: Selection, Materiality & Anchoring 7.5 Exterior Lighting, Photometrics, Dark Sky & Electrical Safety 7.6 Public Playground Safety: CPSC & ASTM Standards 7.7 Planting Design Principles & Ecological Matching 7.8 Water Conservation, Xeriscaping & Irrigation System Principles 7.9 Opinions of Probable Cost & Value Engineering

8 Chapter 8: Construction Drawings, Layout & Detailing

8.1 Drawing Set Hierarchy, Sheet Standards & Drafting Conventions 8.2 Interdisciplinary Coordination & QA/QC Review 8.3 Demolition Plans & Tree Protection Requirements 8.4 Site Preparation: Clearing, Grubbing, Topsoil & Utility Abandonment 8.5 Layout, Dimensioning & Materials Plans 8.6 Planting Plans, Plant Schedules & Installation Details 8.7 Technical Detailing: Pavements, Curbs & Joint Assemblies 8.8 Retaining Wall, Stair & Ramp Detailing Standards

9 Chapter 9: Construction Specifications & Bidding

9.1 CSI MasterFormat Divisions & SectionFormat Structure 9.2 Specification Writing Methods & the Drawings–Specifications Relationship 9.3 Project Manual, General Conditions & Front-End Documents 9.4 Bid Requirements, Bid Forms & Addenda Management 9.5 Pre-Bid Procedures, Bid Opening & Contractor Evaluation

10 Chapter 10: Construction Administration, Submittals & Changes

10.1 Pre-Construction Conference & Construction Administration Authority 10.2 Initial Decision Maker, Communication Protocols & Project Records 10.3 Submittals, Shop Drawings, Product Data & Samples 10.4 Requests for Information (RFIs) & Technical Clarifications 10.5 Change Orders, Construction Change Directives & Claims

11 Chapter 11: Field Observation, Quality Control & Close-Out

11.1 Field Observations, Site Reports & Non-Conforming Work 11.2 Quality Control, Material Testing & Inspections 11.3 Substantial Completion, Punch Lists & Retainage 11.4 Project Close-Out, Guarantees, Warranties & Final Acceptance

12 Chapter 12: Contour Interpretation, Grading & Earthwork Calculations

12.1 Contour Rules & Topographic Landform Interpretation 12.2 Spot Elevations & Contour Interpolation Calculations 12.3 Slope Formulas, Maximum Gradients & Cross Slopes 12.4 Earthwork Calculations: Average End Area & Grid Methods 12.5 Cut and Fill Balancing, Shrinkage, Swell & Mass Haul 12.6 Reviewing Grading Design: Error Detection & Constructability

13 Chapter 13: Stormwater Hydrology, Runoff & BMP Design

13.1 Hydrologic Cycle, Watershed Delineation & Time of Concentration 13.2 Peak Runoff Estimation: The Rational Method (Q = CiA) 13.3 NRCS Curve Number Method & Runoff Hydrographs 13.4 LID Principles, Water Quality Volume & Bioretention Design 13.5 Bioswales, Permeable Pavement, Green Roofs & Harvesting

14 Chapter 14: Site Drainage Systems, Hydraulics & Erosion Control

14.1 Open Channel Hydraulics, Manning’s Equation & Swale Design 14.2 Gutter Flow, Spread & Roadway Inlet Hydraulics 14.3 Subsurface Drainage, Catch Basins & Pipe Invert Calculations 14.4 Stormwater Storage: Detention, Retention & Water Quality Basins 14.5 Reviewing Drainage Plans & Evaluating Design Alternatives 14.6 Erosion Mechanics, RUSLE & the NPDES/SWPPP Framework 14.7 Erosion & Sediment Control BMPs, Basins & Site Stabilization

6.5 ADA & PROWAG Accessible Route Design

Key Takeaways Explain This Topic AI

An accessible route may run at up to 5.00% (1:20) without ramp provisions; any running slope above 5.00% is legally a ramp, with a maximum running slope of 8.33% (1:12) and a maximum cross slope of 2.08% (1:48).

Maximum ramp rise between level landings is 30 inches, which at the 1:12 maximum slope permits a maximum ramp run of 30 feet before a landing is required.

Ramp landings must be at least 60 inches long and at least as wide as the ramp run, and a landing where the ramp changes direction must be at least 60 by 60 inches.

Handrails are required on both sides of any ramp run with a rise greater than 6 inches, mounted 34 to 38 inches above the ramp surface with 12-inch horizontal extensions at top and bottom.

Detectable warning surfaces (truncated domes) are required at curb ramps and blended transitions at street crossings, and must span the full width of the ramp run for a depth of 24 inches in the direction of travel.

Last updated: September 2026

1. Universal Accessibility: 2010 ADA Standards & PROWAG

Federal accessibility legislation ensures that the built environment is usable by individuals with disabilities. Landscape architects must comply with two primary federal standards:

2010 ADA Standards for Accessible Design: Applies to private commercial facilities, places of public accommodation, and state/local government facilities on site parcels (Title II & III).

PROWAG (Public Rights-of-Way Accessibility Guidelines): Developed by the U.S. Access Board specifically for public streets, sidewalks, and pedestrian facilities within public rights-of-way.

The Continuous Accessible Route

An accessible route is a continuous, unobstructed path connecting all accessible site elements—including accessible parking stalls, passenger loading zones, public transit stops, building entrances, and outdoor recreational amenities.

Walkway Slope & Cross-Slope Thresholds

Technical Metric ADA / PROWAG Standard Critical Design / Construction Practice

Maximum Running Slope (Walkway) 5.0% (1:20) Any walkway with a running slope ≤ 5.0 % \le 5.0\% ≤ 5.0% is legally classified as a walkway , requiring NO handrails, landings, or edge protection.

Ramp Threshold > 5.0 % > 5.0\% > 5.0% up to 8.33 % 8.33\% 8.33% (1:12) Any path segment exceeding 5.0 % 5.0\% 5.0% is legally classified as a ramp and must comply with all mandatory ramp regulations.

Maximum Cross Slope 2.08% (1:48) Cross slope directs stormwater off paving. Exam Trap: Standard construction tolerance can cause a 2.0% design cross slope to be built at 2.2%, triggering code failure. Landscape architects must design and specify cross slopes at 1.5% to 1.8% to ensure field-constructed slopes never exceed 2.08%.

Surface Firmness & Stability Firm, Stable, Slip-Resistant (FSR) Surfaces must resist deformation under wheelchair wheels. Concrete, asphalt, and mortared pavers comply. Loose pea gravel, thick bark mulch, and uncompacted dirt do NOT comply.

Vertical Surface Discontinuities Max 1 / 4 inch 1/4\text{ inch} 1/4 inch ( 6.4 mm 6.4\text{ mm} 6.4 mm ) vertical Vertical lips between pavers or concrete joints ≤ 1 / 4 " \le 1/4" ≤ 1/4" require no beveling. Lips between 1 / 4 " 1/4" 1/4" and 1 / 2 " 1/2" 1/2" must be beveled with a slope no steeper than 1:2 . Lips > 1 / 2 " > 1/2" > 1/2" require a ramp.

Ground Grate Openings Max 1 / 2 inch 1/2\text{ inch} 1/2 inch ( 13 mm 13\text{ mm} 13 mm ) in direction of travel Grate slots must run perpendicular to the dominant direction of pedestrian travel to prevent wheelchair casters and cane tips from catching. GROUND DRAINAGE GRATE ORIENTATION

  • INCORRECT: Slots Parallel to Travel CORRECT: Slots Perpendicular
  • =================================== ============================
  • Direction of Travel ===> Direction of Travel ===>
  • ---------------------------------- ||||||||||||||||||||||||||||
  • ---------------------------------- ||||||||||||||||||||||||||||
  • ---------------------------------- ||||||||||||||||||||||||||||
  • (Casters / cane tips drop in slot!) (Max 1/2" opening; wheels roll over)
  • 2. Technical Ramp Design Standards (ADA §405)

When site topography forces a running slope steeper than 1:20 (5.0%), the feature becomes a ramp and must satisfy strict geometric criteria: ANATOMY OF AN ADA RAMP RUN

  • Level Landing Level Landing
  • (Min 60" Long) Max Slope 1:12 (8.33%) (Min 60" Long)
  • [Max 2.0% Slope] +----------------------------+ [Max 2.0% Slope]
  • +---------------+ / \ +---------------+
  • | | / Continuous Handrails \ | |
  • | | / 34" to 38" Height \ | |
  • | |/ \| |
  • +---------------+--------------------------------------+---------------+---
  • |<-------- Max 30'-0" Length --------->|
  • |<-------- (Max 30" Rise) ------------>|
  • Key Ramp Parameters

Maximum Slope: 1:12 (8.33%) . Steeper slopes are strictly prohibited on new construction (historic preservation exceptions permit 1:10 for a 6-inch rise or 1:8 for a 3-inch rise only where extreme physical space constraints exist).

Maximum Rise Per Single Run: 30 inches (760 mm) . This means that at a maximum slope of 1:12, a single uninterrupted ramp run can never exceed 30 feet in horizontal length before requiring an intermediate level landing.

Minimum Clear Width: 36 inches (915 mm) between handrails.

Ramp Landings:

Top and Bottom Landings: Must be level (maximum 2.0% cross/running slope for drainage) and measure at least 60 inches (5 feet) in clear length by at least the width of the ramp.

Turning Landings: Where a ramp changes direction (e.g., switchback or 90-degree turn), the landing must measure at least 60 inches by 60 inches (5'0" x 5'0") to allow a wheelchair occupant to execute a 90-degree or 180-degree turn.

Handrails (ADA §505):

Requirement: Required on both sides of any ramp run with a rise greater than 6 inches (150 mm) .

Height: Continuous top of gripping surface between 34 inches and 38 inches vertically above the ramp walking surface.

Horizontal Extensions: Handrails must extend horizontally at least 12 inches beyond the top and bottom of the ramp run, parallel to the ground surface, and must return smoothly to a wall, post, or floor to eliminate snagging hazards for visually impaired cane users.

Gripping Surface: Circular cross-section with outside diameter between 1.25 inches and 2.0 inches , or non-circular perimeter between 4.0 and 6.25 inches with cross-section dimension max 2.25 inches.

Edge Protection: Required along the open sides of ramp runs and landings to prevent wheelchair casters from slipping off the edge. Achieved by a continuous raised curb at least 2 inches high , a barrier rail located within 4 inches of the floor, or extended solid wall surfaces.

3. Curb Ramps & Blended Transitions (ADA §406 & PROWAG)

Curb ramps provide access between the elevated sidewalk and the street grade at intersections and crosswalks.

Primary Curb Ramp Typologies

Perpendicular Curb Ramp:

The ramp run is oriented perpendicular to the curb line. Pedestrians travel straight down the ramp into the roadway crosswalk.

Flared Sides vs. Returned Curbs: Where pedestrians can walk across the ramp from the sides (e.g., in a wide, fully paved urban sidewalk), the sides must have flared slopes with a maximum gradient of 1:10 (10.0%) . If the sides are bordered by a continuous planting bed, grass verge, or protective retaining wall where foot traffic cannot cross, vertical returned curbs are permissible.

Parallel Curb Ramp:

The sidewalk slopes down parallel to the street curb on both sides to a level turning landing at street grade. The pedestrian then turns 90 degrees to cross the street.

Application: Ideal for narrow rights-of-way or constrained sidewalks where a perpendicular ramp would be too steep or penetrate private property.

Blended Transition:

A raised crosswalk or continuous flush surface connecting the sidewalk directly to the roadway with a running slope of ≤ 5.0 % \le 5.0\% ≤ 5.0% . Eliminates curb ramps entirely.

Detectable Warnings (Truncated Domes)

Purpose: Provide a standardized tactile and visual cue to alert blind or visually impaired pedestrians that they are transitioning from a protected pedestrian zone into an active vehicular roadway.

Specifications: A grid of raised truncated domes with base diameter 0.9 to 1.4 inches, top diameter 0.45 to 0.9 inches, and height of 0.2 inches.

Depth: Must extend 24 inches (610 mm) in the direction of pedestrian travel across the full width of the curb ramp run or landing at the street edge.

Visual Contrast: Must provide a distinct light-on-dark or dark-on-light visual contrast (often safety yellow, dark red, or black depending on adjacent pavement reflectivity). PERPENDICULAR CURB RAMP DETAIL

  • +-------------------------------------------------------------+
  • | Sidewalk Surface |
  • +---------------------+-----------------+---------------------+
  • | Flared Side | Ramp Run | Flared Side |
  • | (Max 1:10 Slope) | (Max 1:12 Slope)| (Max 1:10 Slope) |
  • | | | |
  • +---------------------+-----------------+---------------------+
  • | DETECTABLE | <-- 24" Depth Across
  • | WARNING DOMES | Full Ramp Width
  • ======================+=================+======================
  • Paved Street / Gutter Flowline
  • 4. Accessible Seating Areas and Clear Floor Spaces (ADA §305 & §902)

Universal design mandates that outdoor seating, picnic areas, and assembly spaces integrate accessible accommodations seamlessly into the overall landscape layout:

Clear Floor / Ground Space: An unobstructed, level (max 2.0% slope) surface measuring at least 30 inches by 48 inches (760 mm x 1220 mm) must be provided for a single stationary wheelchair occupant. This space can be positioned for either a forward or parallel approach to site elements.

Knee and Toe Clearance: For dining tables, picnic benches, or public drinking fountains:

Toe Clearance: Extends under the surface at a minimum height of 9 inches above the finished floor, extending up to 6 inches deep.

Knee Clearance: Must provide a clear vertical opening at least 27 inches high , 30 inches wide , and between 17 and 25 inches deep under the table surface.

Tabletop Height: Must be between 28 inches and 34 inches above the finished ground surface.

Seating Dispersion & Social Integration: Wheelchair spaces must not be segregated into isolated corners or clustered at the back of plazas. They must be integrated directly alongside standard bench seating, accompanied by companion seating, and provide equivalent lines of sight and environmental amenities.

5. ADA vs. PROWAG Standards: Side-by-Side Comparison

Design Feature 2010 ADA Standards (Site Parcels) PROWAG (Public Rights-of-Way)

Walkway Running Slope Max 5.0 % 5.0\% 5.0% ( 1 : 20 1:20 1 : 20 ); slopes > 5.0 % > 5.0\% > 5.0% require ramp detailing Matches street grade when following public roadway ROW; otherwise max 5.0 % 5.0\% 5.0%

Cross Slope Max 2.08 % 2.08\% 2.08% ( 1 : 48 1:48 1 : 48 ) absolute Max 2.08 % 2.08\% 2.08% ( 1 : 48 1:48 1 : 48 ); up to 5.0 % 5.0\% 5.0% allowed at pedestrian street crossings without stop control

Ramp Max Slope & Rise Max 8.33 % 8.33\% 8.33% ( 1 : 12 1:12 1 : 12 ); max rise 30 inches 30\text{ inches} 30 inches per run Max 8.33 % 8.33\% 8.33% ( 1 : 12 1:12 1 : 12 ); max rise 30 inches 30\text{ inches} 30 inches per run

Ramp Landings Min 60 " × 60 " 60" \times 60" 60" × 60" at turns; 60 " 60" 60" length at ends Min 60 " × 60 " 60" \times 60" 60" × 60" at turns; 60 " 60" 60" length at ends

Detectable Warnings Required primarily at transit platform edges; optional on private sites Mandatory on all curb ramps, blended transitions, and rail crossings (24" depth)

Clear Walkway Width Min 36 " 36" 36" continuous; 60 " 60" 60" passing spaces every 200 ft 200\text{ ft} 200 ft Min 48 " 48" 48" continuous (exclusive of curb width); 60 " 60" 60" preferred

Handrail Height & Ext. 34 " 34" 34" to 38 " 38" 38" height; 12 " 12" 12" top/bottom horizontal extensions 34 " 34" 34" to 38 " 38" 38" height; 12 " 12" 12" top/bottom horizontal extensions

6. Real-World Case Scenario: Multi-Level Civic Library Plaza

Scenario: A landscape architect is designing a civic plaza connecting an upper street entrance to a lower reading garden that sits 7.5 feet (90 inches) lower. The client wants an accessible pedestrian route that integrates stairs, ramps, and seating terraces without appearing medical or institutional. The horizontal run available along the hillside terrace is 110 feet.

Technical Calculation & Layout:

Total Vertical Rise: 90 inches = 7.5 feet 90\text{ inches} = 7.5\text{ feet} 90 inches = 7.5 feet .

Ramp Feasibility at Max 1:12 Slope:

Total ramp slope run required: 90 inches × 12 = 1 , 080 inches = 90 feet 90\text{ inches} \times 12 = 1,080\text{ inches} = 90\text{ feet} 90 inches × 12 = 1 , 080 inches = 90 feet of pure incline.

Rise per run limit: Maximum 30 inches per run. Therefore, the 90-inch total rise mandates exactly three separate ramp runs ( 90 / 30 = 3 90 / 30 = 3 90/30 = 3 runs), each with a 30-inch vertical rise and 30-foot horizontal length.

Landings: The system requires four level landings (top landing, two intermediate turning landings, bottom landing). Each landing must measure at least 5 feet (60 inches) long. Since the ramp switches back along the terrace, the two intermediate landings must be turning landings measuring at least 5 ft × 5 ft 5\text{ ft} \times 5\text{ ft} 5 ft × 5 ft ( 60 " × 60 " 60" \times 60" 60" × 60" ) .

Total horizontal footprint: Three 30-foot runs ( 90 ft 90\text{ ft} 90 ft ) plus two 5-foot intermediate landings ( 10 ft 10\text{ ft} 10 ft ) plus top and bottom landings ( 10 ft 10\text{ ft} 10 ft ) = 110 feet 110\text{ feet} 110 feet total horizontal run . The available space accommodates the ramp system perfectly.

Handrail Configuration: Continuous handrails are specified on both sides at 36 inches height, extending 12 inches horizontally past each landing transition.

Drainage & Cross Slopes: To ensure compliance after construction, all landing cross slopes are graded at 1.5% , well within the 2.08% legal ceiling.

7. Exam Traps & Pitfalls

The 2.0% Cross-Slope Construction Trap: Exam questions often test whether specifying a 2.0% cross slope on a concrete walk complies with ADA. While 2.0% is technically under the 2.08% (1:48) maximum, in field construction, concrete finishing tolerances frequently exceed 2.0%, resulting in code violations. The correct design specification is always 1.5% to 1.8% .

The 30-Foot Ramp Run Myth: Candidates often mistakenly memorize "ramps can only be 30 feet long." The legal standard under ADA §405.6 is that a ramp run can have a maximum rise of 30 inches . If a ramp is designed at a gentle 1:16 slope, its run could legally extend 40 feet ( 40 × 12 / 16 = 30 " 40 \times 12 / 16 = 30" 40 × 12/16 = 30" rise). The 30-foot limit applies only when operating at the maximum 1:12 slope!

Flared Sides vs. Returned Curbs: Watch for questions depicting curb ramps bordered by pedestrian walkways. If pedestrians can walk across the side of a curb ramp, specifying a vertical returned curb creates an immediate tripping hazard and code violation. Flared sides with a maximum 1:10 slope are legally mandatory.

Handrail Extensions Obstructing Circulation: Remember that the mandatory 12-inch horizontal handrail extensions at the top and bottom of ramps cannot project into intersecting accessible routes or cross-circulation walks. They must return to posts, walls, or be tucked outside the pedestrian path.