Study guide

8.5 Layout, Dimensioning & Materials Plans

Landscape Architect Registration Examination L.A.R.E.

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Project Management, Legal Framework & Contracts

1.1 Professional Practice, Ethics & the HSW Mandate 1.2 Standard of Care, Responsible Charge & Sealing Documents 1.3 Professional Services Agreements & Contract Clauses 1.4 Fee Structures, Compensation Models & Billing 1.5 Project Scheduling, CPM & Budget Management 1.6 Risk Management, Professional Liability & Insurance

2 Chapter 2: Site Inventory, Surveying & Regulatory Framework

2.1 Boundary Surveys, Legal Descriptions & Survey Datums 2.2 Topographic Surveys, Easements & Encumbrances 2.3 Desktop Inventory, GIS Data & Field Reconnaissance 2.4 Policy Documents & Prior Planning Studies 2.5 Adjacent Land Use & Contextual Data Collection 2.6 Stakeholder Engagement & Public Participation 2.7 Zoning Frameworks, Dimensional Standards & FAR 2.8 Parking Standards, Buffer Yards & Zoning Relief 2.9 Clean Water Act Permitting & NEPA Review 2.10 ESA, Floodplain, Coastal & Historic Preservation Compliance

3 Chapter 3: Physical, Contextual & Environmental Site Analysis

3.1 Scoping Site Analysis & Synthesizing Opportunities and Constraints 3.2 Geotechnical Investigation & Soil Classification Systems 3.3 Problematic Soil Conditions & Agronomic Soil Quality 3.4 Topographic Interpretation & Slope Suitability 3.5 Watershed Mechanics, Stream Order & FEMA Flood Hazard Zones 3.6 Wetland Delineation, Classification & Riparian Buffers 3.7 Utility Analysis & Infrastructure Capacity 3.8 Visual Resource & Viewshed Analysis 3.9 Contextual Analysis: Appropriate Use & Future Development Impacts 3.10 Microclimates, Solar Orientation & Vegetation Analysis

4 Chapter 4: Stewardship, Climate Resiliency & Design Principles

4.1 SITES v2 & LEED Site Credit Rating Systems 4.2 Life-Cycle Assessment, Embodied Carbon & Ecosystem Services 4.3 Climate Resiliency, Adaptation & Urban Heat Island Mitigation 4.4 Environmental Justice & Social Equity in Site Design 4.5 Cultural Landscapes, Historic Preservation & Adaptive Reuse

5 Chapter 5: Master Planning, Programming & Land Use

5.1 Project Visioning, Goal Setting & Space Programming 5.2 Carrying Capacity Analysis & NRPA Park Classification Standards 5.3 Site Suitability Synthesis & Opportunities/Constraints Mapping 5.4 Land Use Allocation & Development Scenario Evaluation 5.5 Master Plan Deliverables & Design Guidelines 5.6 Capital Improvement Programming, Phasing & Implementation

6 Chapter 6: Schematic Design & Spatial Organization

6.1 Design Intent, Conceptual Diagrams & Form Generation 6.2 Basis of Design, Alternatives Evaluation & the Preferred Scheme 6.3 Spatial Hierarchy, Outdoor Rooms & Proportion 6.4 Pedestrian Circulation Networks & Environmental Wayfinding 6.5 ADA & PROWAG Accessible Route Design 6.6 Multimodal Transportation, Vehicular Circulation & Parking Layout

7 Chapter 7: Design Development, Materials & Planting Systems

7.1 Paving Systems: Rigid, Flexible & Unit Pavers 7.2 Retaining Walls, Earth Pressure & Wall Drainage 7.3 Wall System Selection, Fences, Screens & Gates 7.4 Site Furnishings: Selection, Materiality & Anchoring 7.5 Exterior Lighting, Photometrics, Dark Sky & Electrical Safety 7.6 Public Playground Safety: CPSC & ASTM Standards 7.7 Planting Design Principles & Ecological Matching 7.8 Water Conservation, Xeriscaping & Irrigation System Principles 7.9 Opinions of Probable Cost & Value Engineering

8 Chapter 8: Construction Drawings, Layout & Detailing

8.1 Drawing Set Hierarchy, Sheet Standards & Drafting Conventions 8.2 Interdisciplinary Coordination & QA/QC Review 8.3 Demolition Plans & Tree Protection Requirements 8.4 Site Preparation: Clearing, Grubbing, Topsoil & Utility Abandonment 8.5 Layout, Dimensioning & Materials Plans 8.6 Planting Plans, Plant Schedules & Installation Details 8.7 Technical Detailing: Pavements, Curbs & Joint Assemblies 8.8 Retaining Wall, Stair & Ramp Detailing Standards

9 Chapter 9: Construction Specifications & Bidding

9.1 CSI MasterFormat Divisions & SectionFormat Structure 9.2 Specification Writing Methods & the Drawings–Specifications Relationship 9.3 Project Manual, General Conditions & Front-End Documents 9.4 Bid Requirements, Bid Forms & Addenda Management 9.5 Pre-Bid Procedures, Bid Opening & Contractor Evaluation

10 Chapter 10: Construction Administration, Submittals & Changes

10.1 Pre-Construction Conference & Construction Administration Authority 10.2 Initial Decision Maker, Communication Protocols & Project Records 10.3 Submittals, Shop Drawings, Product Data & Samples 10.4 Requests for Information (RFIs) & Technical Clarifications 10.5 Change Orders, Construction Change Directives & Claims

11 Chapter 11: Field Observation, Quality Control & Close-Out

11.1 Field Observations, Site Reports & Non-Conforming Work 11.2 Quality Control, Material Testing & Inspections 11.3 Substantial Completion, Punch Lists & Retainage 11.4 Project Close-Out, Guarantees, Warranties & Final Acceptance

12 Chapter 12: Contour Interpretation, Grading & Earthwork Calculations

12.1 Contour Rules & Topographic Landform Interpretation 12.2 Spot Elevations & Contour Interpolation Calculations 12.3 Slope Formulas, Maximum Gradients & Cross Slopes 12.4 Earthwork Calculations: Average End Area & Grid Methods 12.5 Cut and Fill Balancing, Shrinkage, Swell & Mass Haul 12.6 Reviewing Grading Design: Error Detection & Constructability

13 Chapter 13: Stormwater Hydrology, Runoff & BMP Design

13.1 Hydrologic Cycle, Watershed Delineation & Time of Concentration 13.2 Peak Runoff Estimation: The Rational Method (Q = CiA) 13.3 NRCS Curve Number Method & Runoff Hydrographs 13.4 LID Principles, Water Quality Volume & Bioretention Design 13.5 Bioswales, Permeable Pavement, Green Roofs & Harvesting

14 Chapter 14: Site Drainage Systems, Hydraulics & Erosion Control

14.1 Open Channel Hydraulics, Manning’s Equation & Swale Design 14.2 Gutter Flow, Spread & Roadway Inlet Hydraulics 14.3 Subsurface Drainage, Catch Basins & Pipe Invert Calculations 14.4 Stormwater Storage: Detention, Retention & Water Quality Basins 14.5 Reviewing Drainage Plans & Evaluating Design Alternatives 14.6 Erosion Mechanics, RUSLE & the NPDES/SWPPP Framework 14.7 Erosion & Sediment Control BMPs, Basins & Site Stabilization

8.5 Layout, Dimensioning & Materials Plans

Key Takeaways Explain This Topic AI

Horizontal site layout relies on four primary methodologies: State Plane Coordinate geometry (northing/easting point tables), baseline and offset dimensioning, alignment stationing (where 1+00 equals 100 feet), and angle-distance radial stakeout.

String (chain) dimensioning introduces cumulative tolerance error (tolerance stack-up), whereas running (baseline) dimensioning references all measurements from a fixed datum to maintain independent, non-accumulating tolerances.

Horizontal circular curves are mathematically defined by five core geometric parameters: Radius (R), Central Angle/Delta (Δ), Tangent Length (T), Curve Length (L), and Long Chord (C), connecting the Point of Curvature (PC) to the Point of Tangency (PT).

The arc length of a circular curve is calculated using the formula L = (π * R * Δ) / 180°, and the tangent distance from PC or PT to the Point of Intersection (PI) is calculated as T = R * tan(Δ / 2).

Materials plans require distinctive CAD hatch patterns, unambiguous leader callouts, and comprehensive schedules detailing material types, finishes, jointing patterns, unit dimensions, and edge restraints.

Last updated: September 2026

Core Focus: Layout and dimensioning plans (L-300 series) provide the geometric instructions required for professional surveyors and site contractors to translate two-dimensional design concepts onto physical ground. The LARE rigorously tests horizontal layout methodologies, cumulative tolerance error prevention, coordinate geometry, horizontal circular curve trigonometry (PC, PT, PI, R, T, L, Δ), and materials plan coordination.

1. Horizontal Layout Methodologies

The landscape architect must select the appropriate horizontal layout system based on site geometry, scale, and contractor equipment capabilities. The four primary layout systems used in professional practice include: 1. COORDINATE GEOMETRY (PNT / N / E) 2. BASELINE & OFFSET DIMENSIONING

  • N 10,450.25, E 5,120.80 +--- Offset Distance (e.g., 15.0')
  • (Point 101) | |
  • * V V
  • / ================================= (Baseline)
  • / 0+00 1+00 2+00
  • * (Point 102)
  • N 10,410.50, E 5,185.30
  • 3. CENTERLINE ALIGNMENT STATIONING 4. RADIAL / ANGLE-DISTANCE STAKEOUT
  • Path Alignment Point P
  • ----+---------+---------+-----> *
  • 0+00 1+00 2+00 / \
  • (Start) (100') (200') / \ Distance = 145.2'
  • / \ Bearing = N 42°15' E
  • Control *-------*
  • Point A Control Point B
  • 1. Coordinate Geometry (COGO / Northing & Easting)

Mechanics: Every critical site feature (corners of buildings, wall endpoints, curve centers, radius points, walk intersections) is assigned a discrete point number and defined by absolute Cartesian coordinates: Northing ( Y Y Y ) and Easting ( X X X ) , typically tied to the State Plane Coordinate System (SPCS) or a local project datum.

Modern Standard: Driven by total station surveying and GPS/GNSS automated machine guidance (AMG) installed on bulldozers and graders. A Coordinate Point Table is placed directly on the L-300 sheet:

  • Point # Northing (Y) Easting (X) Elevation (Z) Description / Feature
  • 101 10450.25 5120.80 114.50 Back of Curb (BOC) Point of Curvature (PC)
  • 102 10410.50 5185.30 114.85 Back of Curb (BOC) Point of Tangency (PT)
  • 103 10385.00 5240.10 115.20 Radius Center Point ( R = 50.00 ′ R = 50.00' R = 50.0 0 ′ )
  • 2. Baseline and Offset Dimensioning

Mechanics: A known, permanent physical or legal linear boundary serves as the Baseline (such as an exterior architectural building facade, property boundary, or straight street centerline). Features are located by measuring a distance along the baseline and then measuring a perpendicular ( 90 ∘ 90^\circ 9 0 ∘ ) offset distance to the proposed feature.

Best Application: Rectilinear urban plazas, courtyard terraces, athletic fields, and streetscapes abutting established structures.

3. Centerline Alignment Stationing

Mechanics: Used for linear circulation corridors (greenway trails, park roadways, pedestrian promenades, stream restoration alignments). The alignment begins at Station 0 + 00 0+00 0 + 00 and progresses continuously along the centerline.

Stationing Notation: Each full station represents exactly 100 feet (or 100 meters in metric):

Station 0 + 00 = 0.00 feet (Beginning of Alignment) \text{Station } 0+00 = 0.00\text{ feet (Beginning of Alignment)} Station 0 + 00 = 0.00 feet (Beginning of Alignment)

Station 1 + 00 = 100.00 feet \text{Station } 1+00 = 100.00\text{ feet} Station 1 + 00 = 100.00 feet

Station 3 + 45.50 = 345.50 feet from the origin \text{Station } 3+45.50 = 345.50\text{ feet from the origin} Station 3 + 45.50 = 345.50 feet from the origin

Linear Distance Math: The distance between Station 2 + 15.25 2+15.25 2 + 15.25 and Station 7 + 82.75 7+82.75 7 + 82.75 is: 782.75 ft − 215.25 ft = 567.50 feet 782.75\text{ ft} - 215.25\text{ ft} = 567.50\text{ feet} 782.75 ft − 215.25 ft = 567.50 feet

4. Radial Stakeout (Angle & Distance)

Mechanics: A surveyor sets up a total station over a known primary control point (instrument station), backsights on a second known control benchmark, and measures a horizontal clockwise deflection angle and slope/horizontal distance to locate the proposed point.

2. Dimensioning Standards & Cumulative Error Prevention

One of the most heavily tested legal and constructability principles on the LARE is the catastrophic risk of cumulative error (tolerance stack-up) caused by improper dimensioning styles. STRING / CONTINUOUS DIMENSIONING (HIGH RISK OF CUMULATIVE ERROR)

  • |--- 10'-0" ---|--- 12'-0" ---|--- 15'-0" ---|--- 8'-0" ---|--- 10'-0" ---|
  • [Tolerance] [Tolerance] [Tolerance] [Tolerance] [Tolerance]
  • (± 1/4") (± 1/4") (± 1/4") (± 1/4") (± 1/4")
  • -> Total Error can accumulate to ± 1-1/4" or more at the final boundary! <---
  • RUNNING / BASELINE DIMENSIONING (BEST PRACTICE - ZERO ERROR ACCUMULATION)
  • |----------------- 10'-0" ----------------------------------------------->
  • |-------------------------------- 22'-0" --------------------------------->
  • |----------------------------------------------- 37'-0" ------------------>
  • |-------------------------------------------------------------- 45'-0" --->
  • |------------------------------------------------------------------------- 55'-0" ->
  • [DATUM 0'-0"]
  • -> Each measurement has an independent ± 1/4" tolerance tied to datum! <---
  • String (Continuous Chain) Dimensioning vs. Running Dimensioning

String Dimensioning: Dimensions are placed end-to-end in a continuous chain ( A → B → C → D A \to B \to C \to D A → B → C → D ). If field construction tolerance allows ± 1 / 4 \pm 1/4 ± 1/4 inch on each formed element, a string of ten successive planter walls can accumulate over 2 − 1 / 2 2-1/2 2 − 1/2 inches of cumulative displacement . This can force the final curb over a legal property line or encroach on an ADA minimum clearance corridor.

Running Dimensioning (Baseline Dimensioning): All dimensions originate from a single permanent datum point ( 0 ′ − 0 " 0'-0" 0 ′ − 0" ). Each dimension is measured independently back to the datum. Construction tolerances remain isolated and never accumulate .

Professional Dimensioning Rules

Dimension to Finished Faces: Hardscapes must be dimensioned to the Face of Curb (FOC) , Back of Curb (BOC) , or finished face of masonry. Never dimension vaguely to "curb" without designating FOC or BOC.

Tie to Fixed Datums: Every dimension chain must tie to an immovable legal benchmark—such as a building column centerline, exterior finished wall, legal property corner pin, or monumented right-of-way line. Never leave a dimension string "floating in space."

Avoid Over-Dimensioning: Over-dimensioning occurs when every sub-element in a chain is dimensioned alongside an overall dimension. If field conditions vary slightly, conflicting numbers create legal ambiguity. One dimension in the chain should be omitted or labeled as "HOLD" or "VIF" (Verify in Field).

3. Horizontal Circular Curve Geometry & Mathematics

Curvilinear roads, paths, and walls must be documented with absolute mathematical precision. Hand-drawn "spline curves" or loose radii drafted without geometric controls cannot be staked out in the field. PI (Point of Intersection)

  • *
  • /|\
  • / | \
  • / | \
  • / | \
  • Back Tangent (T)/ |E \ Forward Tangent (T)
  • / | \
  • / | \
  • PC *.......|.......* PT
  • (Point of Curvature) \ | M / (Point of Tangency)
  • \ | /
  • \ | /
  • R \ |C / R
  • \ | /
  • \ | /
  • \|/
  • *
  • O (Radius Center)
  • Angle = Delta (Δ)
  • Core Elements of a Simple Circular Curve

R R R = Radius: The fixed perpendicular distance from the circular arc to the center of curvature ( O O O ).

Δ \Delta Δ (Delta) or I I I = Central Angle: The interior angle subtended by the arc, which equals the deflection angle between the intersecting tangents at the PI.

P I PI P I = Point of Intersection: The theoretical point where the back tangent line and forward tangent line intersect.

P C PC PC = Point of Curvature: The point where the alignment transitions from a straight tangent line into the circular curve (also termed the Beginning of Curve / BC).

P T PT PT = Point of Tangency: The point where the circular curve ends and transitions back into a straight tangent line (also termed the End of Curve / EC).

T T T = Tangent Length: The straight-line distance along the tangent line from the P C PC PC to the P I PI P I , or from the P T PT PT to the P I PI P I : T = R × tan ⁡ ( Δ 2 ) T = R \times \tan\left(\frac{\Delta}{2}\right) T = R × tan ( 2 Δ ​ )

L L L = Length of Curve (Arc Length): The actual curved distance traveled along the arc from P C PC PC to P T PT PT : L = 2 π R Δ 360 ∘ = π R Δ 180 ∘ ≈ 0.017453 × R × Δ L = \frac{2\pi R \Delta}{360^\circ} = \frac{\pi R \Delta}{180^\circ} \approx 0.017453 \times R \times \Delta L = 36 0 ∘ 2 π R Δ ​ = 18 0 ∘ π R Δ ​ ≈ 0.017453 × R × Δ

C C C or L C LC L C = Long Chord: The straight-line chord distance connecting P C PC PC directly to P T PT PT : C = 2 R × sin ⁡ ( Δ 2 ) C = 2R \times \sin\left(\frac{\Delta}{2}\right) C = 2 R × sin ( 2 Δ ​ )

E E E = External Distance: The distance from the P I PI P I to the midpoint of the curve arc: E = R × [ sec ⁡ ( Δ 2 ) − 1 ] = R × [ 1 cos ⁡ ( Δ / 2 ) − 1 ] E = R \times \left[\sec\left(\frac{\Delta}{2}\right) - 1\right] = R \times \left[\frac{1}{\cos(\Delta/2)} - 1\right] E = R × [ sec ( 2 Δ ​ ) − 1 ] = R × [ cos ( Δ/2 ) 1 ​ − 1 ]

M M M = Middle Ordinate: The distance from the midpoint of the long chord to the midpoint of the curve arc: M = R × [ 1 − cos ⁡ ( Δ 2 ) ] M = R \times \left[1 - \cos\left(\frac{\Delta}{2}\right)\right] M = R × [ 1 − cos ( 2 Δ ​ ) ]

Curve Math Example on the LARE

Scenario: A park roadway alignment features a horizontal curve with a radius R = 200.00 feet R = 200.00\text{ feet} R = 200.00 feet and a central angle Δ = 45 ∘ 00 ′ 00 " \Delta = 45^\circ 00' 00" Δ = 4 5 ∘ 0 0 ′ 00" ( 45.0 ∘ 45.0^\circ 45. 0 ∘ ).

Calculate Tangent Length ( T T T ): T = 200 × tan ⁡ ( 45 ∘ 2 ) = 200 × tan ⁡ ( 22.5 ∘ ) = 200 × 0.41421 = 82.84 feet T = 200 \times \tan\left(\frac{45^\circ}{2}\right) = 200 \times \tan(22.5^\circ) = 200 \times 0.41421 = 82.84\text{ feet} T = 200 × tan ( 2 4 5 ∘ ​ ) = 200 × tan ( 22. 5 ∘ ) = 200 × 0.41421 = 82.84 feet

Calculate Arc Length ( L L L ): L = π × 200 × 45 ∘ 180 ∘ = 3.14159 × 9000 180 = 157.08 feet L = \frac{\pi \times 200 \times 45^\circ}{180^\circ} = \frac{3.14159 \times 9000}{180} = 157.08\text{ feet} L = 18 0 ∘ π × 200 × 4 5 ∘ ​ = 180 3.14159 × 9000 ​ = 157.08 feet

Stationing Progression: If the P C PC PC is located at Station 4 + 25.00 4+25.00 4 + 25.00 , the P T PT PT stationing is determined by adding the Arc Length ( L L L ) , NEVER the tangent distance: PT Station = ( 4 + 25.00 ) + 157.08 ft = Station 5 + 82.08 \text{PT Station} = (4+25.00) + 157.08\text{ ft} = \text{Station } 5+82.08 PT Station = ( 4 + 25.00 ) + 157.08 ft = Station 5 + 82.08

  • 4. Compound, Reverse & Transition Curves COMPOUND CURVE (PCC) REVERSE CURVE (PRC)
  • (Same Direction, R1 != R2) (Opposite Directions)
  • R1 R1
  • / /
  • / /

PC---*......... PC---*.........

  • * PCC (Common Tangent) * PRC (Inflection)
  • / / \
  • / / \
  • R2 / R2
  • / PT \
  • PT \

Compound Curve: Two or more circular arcs curving in the same direction with different radii that share a common tangent point designated as the Point of Compound Curvature (PCC) . Used in vehicular turning loops and highway off-ramps to decelerate traffic smoothly.

Reverse Curve: Two circular arcs curving in opposite directions sharing a common tangent point designated as the Point of Reverse Curvature (PRC) . Design Warning: On vehicular roads and high-speed multi-use bicycle trails, a straight tangent segment (minimum 50 to 100 feet) should be inserted between reversing curves to prevent sudden lateral weight transfer and loss of vehicular control.

5. Materials Plans, Hatch Symbology & Material Schedules

The Materials Plan (often integrated with L-300) conveys hardscape finishes, paving types, patterns, and jointing systems.

CAD Hatching Standards and Conventions

Each distinct hardscape surface must feature a visually unique, high-contrast hatch pattern (e.g., herringbone for unit pavers, stipple for cast-in-place concrete, diagonal cross-hatch for asphalt, dashed diagonal for crushed stone).

Patterns must be scaled consistently across sheets and oriented to reflect true laying angles (e.g., a 45-degree herringbone paver pattern must be drawn at 45 degrees relative to the curb baseline).

Materials Legend & Hardscape Schedule

Every material depicted on the plan must be linked via callout bubbles to an exhaustive Materials Schedule :

Tag Material Name Product / Manufacturer Nominal Dimensions Color / Finish Setting Bed / Base Course Spec Section

P-1 Architectural CIP Concrete Local Ready-Mix Class A 10 ′ × 10 ′ 10' \times 10' 1 0 ′ × 1 0 ′ joint modules Medium broom finish, uncolored 4 " 4" 4" compacted aggregate base 32 13 13

P-2 Permeable Concrete Paver Hanover Aqua-Loc or equal 4 " × 8 " × 3 − 1 / 8 " 4" \times 8" \times 3-1/8" 4" × 8" × 3 − 1/8" Charcoal / Natural; shot-blast 2 " 2" 2" ASTM #8 aggregate bed 32 14 13

P-3 Porous Asphalt Plant-mixed hot bituminous Continuous wearing course Standard black aggregate 6 " 6" 6" ASTM #57 stone reservoir 32 12 16

C-1 Granite Curb Header Cold Spring Granite 6 " width × 18 " depth 6" \text{ width} \times 18" \text{ depth} 6" width × 18" depth Thermal top, split face Poured concrete haunch 32 16 13

Transitions and Edge Restraints

Materials plans must call out every boundary transition between contrasting materials:

Where unit pavers meet flexible asphalt or lawn, a rigid edge restraint (cast-in-place concrete curb or anchored metal edge) is structurally required.

Where paving abuts buildings, a 1/2-inch preformed expansion joint filler with elastomeric polyurethane sealant must be specified.

6. Layout & Geometry Standards: Comprehensive Comparison

Layout Method / Geometry Primary Data Required Tolerance Risk Ideal Site Application Critical Drafting Requirement

Coordinate Geometry (COGO) Northing, Easting, Point ID Negligible (independent points) Large parks, complex curvilinear plazas, GNSS machine grading Point Table listing all coordinates and descriptions

Baseline & Offset Baseline station, offset distance ( 90 ∘ 90^\circ 9 0 ∘ ) Low to moderate Rectilinear plazas, urban streetscapes, building courtyards Unambiguous permanent physical baseline callout

Centerline Stationing Stations ( 1 + 00 = 100 ′ 1+00 = 100' 1 + 00 = 10 0 ′ ), offsets Negligible along alignment Greenway trails, roadways, linear park walkways Station tick marks every 100 ′ 100' 10 0 ′ , PC/PT station callouts

String Dimensioning Incremental chains ( A → B A \to B A → B ) High (cumulative error) Small residential gardens only Warning: Must include an omitted closure dimension

Running Dimensioning Cumulative measurements from datum Zero cumulative error Commercial plazas, civic terraces, streetscapes Clear 0 ′ − 0 " 0'-0" 0 ′ − 0" datum callout linked to survey benchmark

Simple Circular Curve R , Δ , L , T , C R, \Delta, L, T, C R , Δ , L , T , C Moderate Curving drives, sidewalk radii, garden bed sweeps Curve Table defining R , Δ , L , T , P C , P T R, \Delta, L, T, PC, PT R , Δ , L , T , PC , PT

7. Real-World Case Scenario: The Waterfront Promenade Dimensioning Error

Scenario: A landscape architect prepared the layout and materials plan (Sheet L-301) for a $4.2 million downtown waterfront promenade. The design featured an alternating sequence of fourteen granite planters, each specified at 8'-0" in width, separated by 12'-0" permeable paver sitting bays, terminating at a grand public stair that connected to an adjacent municipal ferry terminal. The drafter dimensioned the entire 280-foot promenade using string (continuous chain) dimensioning , dimensioning each planter and sitting bay end-to-end.

The Field Error: During construction, the masonry contractor formed the granite planters with a minor trade tolerance of + 3 / 8 +3/8 + 3/8 inch per planter. In addition, the paver contractor's joint spacers ran + 1 / 8 +1/8 + 1/8 inch wider than nominal over each sitting bay. Because there was no running baseline dimension and no omitted closure dimension, the error accumulated across the fourteen successive modules: Total Error = ( 14 × + 0.375 " ) + ( 13 × + 0.125 " ) = 5.25 " + 1.625 " = + 6.875 inches \text{Total Error} = (14 \times +0.375") + (13 \times +0.125") = 5.25" + 1.625" = +6.875\text{ inches} Total Error = ( 14 × + 0.375" ) + ( 13 × + 0.125" ) = 5.25" + 1.625" = + 6.875 inches

The Crisis: When the contractor arrived at the end of the promenade, the final granite planter encroached by nearly 7 inches into the clear landing of the grand stair, reducing the required ADA egress path below the federal statutory minimum of 48 inches.

The Remedy: The landscape architect was held responsible for defective contract documentation due to the failure to utilize running dimensions or provide an omitted adjustment bay. The owner required two completed granite planters to be jackhammered out, redesigned, and rebuilt at the landscape architect's expense, delaying the ferry terminal grand opening by four weeks.

8. Exam Traps & Common Pitfalls

The String Dimensioning Cumulative Error Trap: On LARE layout questions, anytime you see a long string of chained dimensions without a single fixed datum, recognize the risk of cumulative error . Running (cumulative) dimensioning is the correct professional answer to maintain independent tolerances.

The PT Stationing Calculation Fallacy: When calculating the station of a Point of Tangency ( P T PT PT ) given the Point of Curvature ( P C PC PC ), candidates frequently add the Tangent Length ( T T T ) or Long Chord ( C C C ). This is incorrect! Stationing measures linear distance along the actual alignment curve. Therefore: PT Station = PC Station + Arc Length ( L ) \text{PT Station} = \text{PC Station} + \text{Arc Length } (L) PT Station = PC Station + Arc Length ( L )

Back of Curb vs. Face of Curb: Look carefully at dimension leaders. Dimensioning to the Back of Curb (BOC) defines the boundary where paving meets planting or sidewalk; dimensioning to the Face of Curb (FOC) defines the gutter street width. Mixing these dimensions creates massive roadway alignment errors.

Over-Dimensioning Legal Disputes: Providing complete string dimensions plus an overall dimension without an adjustment gap creates an over-constrained geometry that triggers contractor claims when field conditions vary by even a half-inch.