Study guide

9.2 Regional Priority Credits

LEED AP Building Design + Construction BD+C

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Introduction & Exam Overview

1.1 Current Exam Facts 1.2 How to Use This Guide

2 Chapter 2: Integrative Process

2.1 Integrative Process Philosophy and Workflow 2.2 Integrative Process Credit (IP) 2.3 Prerequisites and Project Setup 2.4 Certification Levels and Scorecard

3 Chapter 3: Location & Transportation + Surroundings

3.1 LEED for Neighborhood Development Location 3.2 Sensitive Land Protection & High Priority Site 3.3 Surrounding Density and Diverse Uses 3.4 Access to Quality Transit 3.5 Bicycle Facilities, Reduced Parking, Green Vehicles 3.6 Building Surroundings and Joint Use

4 Chapter 4: Sustainable Sites (SS)

4.1 SS Prerequisite: Construction Activity Pollution Prevention 4.2 Site Assessment and Site Development 4.3 Open Space and Rainwater Management 4.4 Heat Island Reduction 4.5 Light Pollution Reduction

5 Chapter 5: Water Efficiency (WE)

5.1 WE Prerequisites 5.2 Outdoor and Indoor Water Use Reduction Credits 5.3 Cooling Tower Water Use, Process Water, and Metering 5.4 Non-Potable and Reclaimed Water Strategies

6 Chapter 6: Energy & Atmosphere (EA)

6.1 EA Prerequisites 6.2 Optimize Energy Performance 6.3 Enhanced Commissioning 6.4 Advanced Energy Metering and Grid Harmonization 6.5 Renewable Energy and Carbon Offsets 6.6 ASHRAE 90.1-2016 Fundamentals

7 Chapter 7: Materials & Resources (MR)

7.1 MR Prerequisites 7.2 Building Life-Cycle Impact Reduction (BLIR) 7.3 Building Product Disclosure and Optimization (BPDO) 7.4 Construction and Demolition Waste Management 7.5 PBT Source Reduction and Furniture Material

8 Chapter 8: Indoor Environmental Quality (EQ)

8.1 EQ Prerequisites 8.2 Enhanced IAQ Strategies and Low-Emitting Materials 8.3 Construction IAQ Management and Assessment 8.4 Thermal Comfort 8.5 Interior Lighting and Daylight 8.6 Quality Views and Acoustic Performance

9 Chapter 9: Innovation, Regional Priority & Project Types

9.1 Innovation Credits 9.2 Regional Priority Credits 9.3 BD+C Project Types and Scope 9.4 Project Registration, Documentation, and Certification Process 9.5 Last-Minute Exam Tips

9.2 Regional Priority Credits

Key Takeaways Explain This Topic AI

Regional Priority (RP) is worth up to 4 points and rewards achievement of credits USGBC has identified as priorities for the project's specific geographic location.

USGBC designates 6 Regional Priority credits per region; achieving any one of them earns 1 bonus RP point — up to a 4-point cap.

RP designations are looked up by ZIP code (U.S.) or postal code (international) on the USGBC Regional Priority lookup tool.

RP points are 'bonus' points layered on top of the original credit — the team still earns the base credit and adds the RP point.

Common regional priorities reflect local environmental pressures: water in the arid Southwest, materials in dense urban centers, heat-island reduction in hot climates, and rainwater management in wet climates.

Last updated: May 2026

What Regional Priority Does

LEED is a national (and international) rating system, but environmental priorities vary by location. A project in Phoenix, Arizona faces very different challenges than one in Portland, Oregon or Manhattan, New York . The Regional Priority (RP) category exists to close that gap by awarding bonus points for credits that address each region's most pressing environmental issues.

Regional Priority is the only LEED category that pays out for credits you already earned — it is essentially a multiplier on geographically relevant work.

How the Math Works

USGBC's Regional Councils identify 6 Regional Priority credits for each defined region.

A region is bounded by ZIP code in the United States and by postal code internationally.

For each of those 6 credits a project achieves, it earns 1 bonus RP point .

The RP category is capped at 4 points per project, even if the project earns all 6 RP-designated credits.

The project still earns the base credit in its original category — RP adds a point on top.

Example: If a Phoenix project earns 4 RP-designated credits (say, WE Credit Outdoor Water Use Reduction, WE Credit Cooling Tower Water Use, SS Credit Heat Island Reduction, and SS Credit Rainwater Management), the project receives those credits' base points plus 4 RP bonus points .

How to Look Up Regional Priorities

Visit USGBC's Regional Priority lookup tool on usgbc.org .

Enter the project's ZIP/postal code.

The tool returns the 6 designated credits and their thresholds (some RP credits award the bonus only at higher achievement tiers).

Teams should perform this lookup in the pre-design phase — knowing the regional priorities early can shape which credits the team pursues at higher thresholds.

Typical Regional Patterns

Region Type Common Priority Areas Example Credits

Arid Southwest (AZ, NM, NV) Water conservation, heat islands WE Outdoor Water Use Reduction, SS Heat Island Reduction

Dense urban cores (NYC, SF, Chicago) Materials reuse, transit access, density MR Building Product Disclosure & Optimization, LT Access to Quality Transit

Hot, humid climates (FL, TX Gulf Coast) Cooling-energy reduction, ventilation EA Optimize Energy Performance, EQ Enhanced IAQ Strategies

Pacific Northwest (OR, WA) Rainwater, daylight, sustainable forestry SS Rainwater Management, MR Sourcing of Raw Materials

Cold climates (Upper Midwest, New England) Heating energy, snow/ice runoff EA Optimize Energy Performance, SS Rainwater Management

International dry climates (UAE, Israel) Water and energy combined WE Indoor Water Use Reduction, EA Optimize Energy Performance

These are illustrative — actual designations vary credit-by-credit and update over time. The exam will not ask you to memorize specific ZIP codes, but it may ask you to explain how to find the priorities or to recognize that the cap is 4 points .

Exam Tips for Regional Priority

The category is worth up to 4 points , not 6 — even though 6 credits are designated.

Points are automatic once a designated credit is achieved at the listed threshold; the team does not submit a separate RP form.

A team cannot choose different RP credits than the ones USGBC has designated for that ZIP — the list is fixed by location.

RP is not a category of new credits — every RP credit is an existing credit elsewhere in LEED.