Study guide

2.4 Certification Levels and Scorecard

LEED AP Building Design + Construction BD+C

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Introduction & Exam Overview

1.1 Current Exam Facts 1.2 How to Use This Guide

2 Chapter 2: Integrative Process

2.1 Integrative Process Philosophy and Workflow 2.2 Integrative Process Credit (IP) 2.3 Prerequisites and Project Setup 2.4 Certification Levels and Scorecard

3 Chapter 3: Location & Transportation + Surroundings

3.1 LEED for Neighborhood Development Location 3.2 Sensitive Land Protection & High Priority Site 3.3 Surrounding Density and Diverse Uses 3.4 Access to Quality Transit 3.5 Bicycle Facilities, Reduced Parking, Green Vehicles 3.6 Building Surroundings and Joint Use

4 Chapter 4: Sustainable Sites (SS)

4.1 SS Prerequisite: Construction Activity Pollution Prevention 4.2 Site Assessment and Site Development 4.3 Open Space and Rainwater Management 4.4 Heat Island Reduction 4.5 Light Pollution Reduction

5 Chapter 5: Water Efficiency (WE)

5.1 WE Prerequisites 5.2 Outdoor and Indoor Water Use Reduction Credits 5.3 Cooling Tower Water Use, Process Water, and Metering 5.4 Non-Potable and Reclaimed Water Strategies

6 Chapter 6: Energy & Atmosphere (EA)

6.1 EA Prerequisites 6.2 Optimize Energy Performance 6.3 Enhanced Commissioning 6.4 Advanced Energy Metering and Grid Harmonization 6.5 Renewable Energy and Carbon Offsets 6.6 ASHRAE 90.1-2016 Fundamentals

7 Chapter 7: Materials & Resources (MR)

7.1 MR Prerequisites 7.2 Building Life-Cycle Impact Reduction (BLIR) 7.3 Building Product Disclosure and Optimization (BPDO) 7.4 Construction and Demolition Waste Management 7.5 PBT Source Reduction and Furniture Material

8 Chapter 8: Indoor Environmental Quality (EQ)

8.1 EQ Prerequisites 8.2 Enhanced IAQ Strategies and Low-Emitting Materials 8.3 Construction IAQ Management and Assessment 8.4 Thermal Comfort 8.5 Interior Lighting and Daylight 8.6 Quality Views and Acoustic Performance

9 Chapter 9: Innovation, Regional Priority & Project Types

9.1 Innovation Credits 9.2 Regional Priority Credits 9.3 BD+C Project Types and Scope 9.4 Project Registration, Documentation, and Certification Process 9.5 Last-Minute Exam Tips

2.4 Certification Levels and Scorecard

Key Takeaways Explain This Topic AI

LEED awards four certification levels — Certified (40-49 points), Silver (50-59), Gold (60-79), and Platinum (80+) — out of 110 total possible points

Energy & Atmosphere (EA) is the largest category at 33 points, more than three times the size of Sustainable Sites and roughly one-third of all available points

The base scorecard sums to 100 points; the remaining 10 points come from Innovation (6) and Regional Priority (4), which depend on context and ZIP code

Prerequisites are mandatory and award zero points — every BD+C project must satisfy every prerequisite in every category before any credit in that category counts

Prerequisites span Integrative Process, Location & Transportation, Sustainable Sites, Water Efficiency, Energy & Atmosphere, Materials & Resources, and Indoor Environmental Quality

Last updated: May 2026

The Four Certification Levels

LEED uses the same four certification levels across every rating system. Memorize these thresholds cold — they show up on nearly every LEED AP exam.

  • Certification Level Points Required (out of 110)
  • Certified 40-49
  • Silver 50-59
  • Gold 60-79
  • Platinum 80+

A few rules the exam tests:

Points are cumulative across categories — a Gold project can come from many small wins or a few category sweeps

There is no minimum per category beyond the prerequisites — a project can earn zero Materials credits and still hit Platinum if it dominates Energy and Water

  • Prerequisites award zero points but are required for any certification level
  • The point thresholds are the same in BD+C, ID+C, O+M, ND, and Homes
  • The 110-Point Scorecard (LEED v4.1 BD+C)

LEED v4.1 BD+C uses a 100-point base scorecard plus 10 bonus points from Innovation and Regional Priority.

  • # Category Code Points Share
  • 1 Integrative Process IP 1 1%
  • 2 Location & Transportation LT 16 15%
  • 3 Sustainable Sites SS 10 9%
  • 4 Water Efficiency WE 11 10%
  • 5 Energy & Atmosphere EA 33 30%
  • 6 Materials & Resources MR 13 12%
  • 7 Indoor Environmental Quality EQ 16 15%
  • Base subtotal 100
  • 8 Innovation IN 6 5%
  • 9 Regional Priority RP 4 4%
  • Total possible 110 100%
  • Why the Distribution Matters

EA is dominant — at 33 points it is more than 3x larger than the next-largest category (LT and EQ at 16 each). The exam expects you to know EA is the biggest lever.

IP is symbolic — 1 point — but it disproportionately shapes performance in every other category

Innovation (IN) rewards strategies above credit thresholds, novel approaches not covered by existing credits, and pilot credits — and includes 1 point for having a LEED AP with a specialty matching the project rating system on the team

Regional Priority (RP) awards bonus points (up to 4) when a project achieves credits that USGBC has flagged as locally important based on the project's ZIP code

LEED v4.1 BD+C Points by Category

Prerequisites: The Mandatory Floor

Prerequisites are mandatory items that earn zero points but must all be satisfied to certify at any level. A project that hits 110 points on the scorecard but fails one prerequisite is not certified at all. The exam loves this point — expect a scenario question that ends with 'but the project did not meet the Minimum Energy Performance prerequisite' and the right answer to be 'no certification.'

The LEED v4.1 BD+C prerequisites are listed below. Memorize the category and the name of each — the exam asks both 'which is a prerequisite' and 'which category does this prerequisite belong to.'

  • Integrative Process (IP)
  • No prerequisites — the IP credit is voluntary but recommended
  • Location & Transportation (LT)
  • No standalone prerequisites — LT requirements are integrated into the rating system structure
  • Sustainable Sites (SS)

SS Prerequisite: Construction Activity Pollution Prevention — Create and implement an Erosion and Sedimentation Control (ESC) plan that conforms to the 2017 U.S. EPA Construction General Permit (CGP) or local equivalent. Required for every BD+C project.

Water Efficiency (WE)

WE Prerequisite: Outdoor Water Use Reduction — Reduce outdoor water use by either (a) eliminating permanent irrigation after a 2-year establishment period or (b) reducing landscape water use by 30% from a calculated baseline.

WE Prerequisite: Indoor Water Use Reduction — Reduce indoor water use by 20% (relative to the LEED v4 baseline) using compliant plumbing fixtures and fittings.

WE Prerequisite: Building-Level Water Metering — Install permanent water meters that measure total potable water use for the building and grounds, with data reported monthly and annually to USGBC for 5 years.

Energy & Atmosphere (EA)

EA Prerequisite: Fundamental Commissioning and Verification — Engage a Commissioning Authority (CxA) by the end of design development to verify that energy, water, indoor environmental quality, and durability systems perform per the OPR and BOD.

EA Prerequisite: Minimum Energy Performance — Demonstrate at least a 5% improvement over the ASHRAE 90.1-2016 baseline for new construction (3% for major renovations) using whole-building energy simulation or prescriptive paths.

EA Prerequisite: Building-Level Energy Metering — Install permanent meters that measure total building energy use across all fuel sources, with data reported monthly and annually to USGBC for 5 years.

EA Prerequisite: Fundamental Refrigerant Management — Do not use chlorofluorocarbon (CFC)-based refrigerants in new HVAC&R systems.

Materials & Resources (MR)

MR Prerequisite: Storage and Collection of Recyclables — Provide dedicated areas for the collection and storage of recyclables (mixed paper, corrugated cardboard, glass, plastics, metals), and for two of: batteries, mercury-containing lamps, and electronic waste.

MR Prerequisite: Construction and Demolition Waste Management Planning — Develop and implement a written plan that identifies the materials targeted for diversion and the diversion strategy.

Indoor Environmental Quality (EQ)

EQ Prerequisite: Minimum Indoor Air Quality Performance — Meet ASHRAE 62.1-2016 minimum ventilation rates (or local equivalent for projects outside the U.S.).

EQ Prerequisite: Environmental Tobacco Smoke Control — Prohibit smoking inside the building and within 25 ft of operable windows, entries, and outdoor air intakes; or implement a compliant building-wide no-smoking policy with signage.

Prerequisite Memory Aid

A helpful pattern: in every major category, there is a prerequisite for performance (you must hit a floor) and one for measurement (you must be able to prove it).

  • Category Performance Floor Measurement
  • Water Efficiency Indoor 20% reduction + outdoor reduction Building-level water metering
  • Energy & Atmosphere 5% better than ASHRAE 90.1 + no CFCs Building-level energy metering

Indoor Environmental Quality ASHRAE 62.1 ventilation + no smoking (no separate metering prerequisite, but EQ credits include monitoring)

Pursuing a Specific Certification Level

Project teams typically work backwards from a target level. A common Gold strategy in BD+C:

  • All prerequisites satisfied (required regardless)
  • ~25 points from EA (energy modeling, commissioning credits, renewables, refrigerants)
  • ~10 points from LT (site selection, transit, parking)
  • ~7 points from WE (above prerequisite reductions)
  • ~8 points from EQ (low-emitting materials, daylight, views)
  • ~5 points from MR (EPDs, sourcing, recycled content)
  • ~4 points from SS (open space, heat island, rainwater)
  • IP credit (1 point)
  • Several IN and RP bonuses

That path lands roughly 60-65 points — comfortably into Gold with some buffer for review attrition.

Scorecard Pitfalls

Submittal attrition. Teams routinely lose 5-10 points during GBCI review when documentation falls short. Target a buffer above the level boundary.

Innovation (IN) overload. Only 5 credits in IN are available — you cannot stack endless innovations to overshoot a level.

Regional Priority (RP) is location-locked. RP credits are pre-selected by USGBC for each ZIP code; teams cannot pick their own RP credits.

Prerequisites do not count. A project that 'almost' has a prerequisite has nothing — partial credit does not exist for prerequisites.

LEED v4.1 BD+C Certification Level Thresholds