Study guide

7.3 Building Product Disclosure and Optimization (BPDO)

LEED AP Building Design + Construction BD+C

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Introduction & Exam Overview

1.1 Current Exam Facts 1.2 How to Use This Guide

2 Chapter 2: Integrative Process

2.1 Integrative Process Philosophy and Workflow 2.2 Integrative Process Credit (IP) 2.3 Prerequisites and Project Setup 2.4 Certification Levels and Scorecard

3 Chapter 3: Location & Transportation + Surroundings

3.1 LEED for Neighborhood Development Location 3.2 Sensitive Land Protection & High Priority Site 3.3 Surrounding Density and Diverse Uses 3.4 Access to Quality Transit 3.5 Bicycle Facilities, Reduced Parking, Green Vehicles 3.6 Building Surroundings and Joint Use

4 Chapter 4: Sustainable Sites (SS)

4.1 SS Prerequisite: Construction Activity Pollution Prevention 4.2 Site Assessment and Site Development 4.3 Open Space and Rainwater Management 4.4 Heat Island Reduction 4.5 Light Pollution Reduction

5 Chapter 5: Water Efficiency (WE)

5.1 WE Prerequisites 5.2 Outdoor and Indoor Water Use Reduction Credits 5.3 Cooling Tower Water Use, Process Water, and Metering 5.4 Non-Potable and Reclaimed Water Strategies

6 Chapter 6: Energy & Atmosphere (EA)

6.1 EA Prerequisites 6.2 Optimize Energy Performance 6.3 Enhanced Commissioning 6.4 Advanced Energy Metering and Grid Harmonization 6.5 Renewable Energy and Carbon Offsets 6.6 ASHRAE 90.1-2016 Fundamentals

7 Chapter 7: Materials & Resources (MR)

7.1 MR Prerequisites 7.2 Building Life-Cycle Impact Reduction (BLIR) 7.3 Building Product Disclosure and Optimization (BPDO) 7.4 Construction and Demolition Waste Management 7.5 PBT Source Reduction and Furniture Material

8 Chapter 8: Indoor Environmental Quality (EQ)

8.1 EQ Prerequisites 8.2 Enhanced IAQ Strategies and Low-Emitting Materials 8.3 Construction IAQ Management and Assessment 8.4 Thermal Comfort 8.5 Interior Lighting and Daylight 8.6 Quality Views and Acoustic Performance

9 Chapter 9: Innovation, Regional Priority & Project Types

9.1 Innovation Credits 9.2 Regional Priority Credits 9.3 BD+C Project Types and Scope 9.4 Project Registration, Documentation, and Certification Process 9.5 Last-Minute Exam Tips

7.3 Building Product Disclosure and Optimization (BPDO)

Key Takeaways Explain This Topic AI

BPDO has three separate credits — Environmental Product Declarations, Sourcing of Raw Materials, and Material Ingredients — and each is worth 1-2 points.

EPDs from at least 20 different manufacturers (each counting as one product) earns the disclosure point; products with verified impact reductions earn the optimization point.

Sourcing of Raw Materials rewards CSR reports aligned with GRI or UNEP and rewards products meeting at least one Leadership Extraction Practice such as recycled content, FSC wood, bio-based, materials reuse, EPR, or local sourcing within 100 miles.

Material Ingredients disclosure pathways include Health Product Declarations (HPDs), Cradle to Cradle, Declare labels, and GreenScreen v1.4 Benchmarks; optimization rewards avoidance of REACH SVHC and Living Building Challenge Red List chemicals.

Locally extracted or manufactured products (within 100 miles) count at 200% of their cost in the Sourcing of Raw Materials calculation.

Last updated: May 2026

The Three BPDO Credits at a Glance

Building Product Disclosure and Optimization (BPDO) is a three-credit family — each credit worth up to 2 points (1 for disclosure, 1 for optimization). All three use the same general counting approach: 20 different permanently installed products from 5 different manufacturers is the disclosure threshold for the first point, and 25% by cost of the total permanently installed products is the optimization threshold for the second point.

Credit Disclosure (1 pt) Optimization (1 pt)

Environmental Product Declarations 20 products from 5 manufacturers with EPDs 50% by cost of products with verified impact reductions

Sourcing of Raw Materials 20 products from 5 manufacturers with GRI/UNEP CSR reports 25% by cost of products meeting leadership extraction criteria

Material Ingredients 20 products from 5 manufacturers with ingredient disclosure 25% by cost of products meeting optimization criteria

  • BPDO Credit 1: Environmental Product Declarations (EPDs)
  • What an EPD Is

An Environmental Product Declaration (EPD) is a third-party-verified document that reports the environmental performance of a product across its life cycle. It is based on product category rules (PCRs) and conforms to ISO 14025 , ISO 21930 , or EN 15804 .

There are two valid types:

Industry-wide (generic) EPD — represents an industry average; counts as one-half (½) product toward the 20-product threshold.

Product-specific (Type III) EPD — manufacturer-specific, third-party verified; counts as one (1) whole product .

Disclosure Point (1 pt)

Use at least 20 different permanently installed products with EPDs from at least 5 different manufacturers .

Optimization Point (1 pt)

Use products that demonstrate impact reductions below industry averages in at least three of the six LCA impact categories. The optimized product cost must total at least 50% by cost of the project's permanently installed products.

  • BPDO Credit 2: Sourcing of Raw Materials
  • Disclosure Point (1 pt)

Use products from at least 5 manufacturers that have publicly released corporate sustainability reports (CSR) aligned with the Global Reporting Initiative (GRI) , United Nations Global Compact , UNEP , or ISO 26000 . Each report represents a manufacturer (not a product); count at least 20 different products from those manufacturers.

Optimization Point — Leadership Extraction Practices (1 pt)

Use products meeting at least one of the following leadership extraction criteria , with the total contributing cost at least 25% of permanently installed products:

  • Practice Threshold
  • Recycled content (Post-consumer + ½ pre-consumer) ≥ 25% by weight
  • Bio-based products Sustainable Agriculture Network's Sustainable Agriculture Standard, or USDA BioPreferred
  • Wood products Forest Stewardship Council (FSC) certified
  • Materials reuse Salvaged, refurbished, or reused
  • Extended producer responsibility (EPR) Manufacturer take-back program
  • Locally sourced Extracted, manufactured, and purchased within 100 miles of the project

Local multiplier: Products that are locally extracted, manufactured, and purchased count at 200% of their cost in the calculation, doubling their contribution toward the 25% threshold.

This is what older LEED versions called Regional Materials . In v4 it lives inside the Sourcing credit, not as a stand-alone credit.

  • BPDO Credit 3: Material Ingredients
  • Disclosure Point (1 pt) — Option 1

Use at least 20 different permanently installed products from at least 5 manufacturers that use any of these chemical inventory pathways to at least 0.1% (1,000 ppm) :

  • Health Product Declaration (HPD) — published HPD with full disclosure
  • Cradle to Cradle (C2C) certification — v2 Basic or higher; v3 Bronze or higher
  • Declare label (International Living Future Institute)
  • Product Lens Certification
  • ANSI/BIFMA e3 Furniture Sustainability Standard (Section 7.5.1)
  • Any USGBC-approved program
  • Optimization Point (1 pt)

Use products that go beyond disclosure to demonstrate optimization through any of:

GreenScreen v1.4 Benchmark — Benchmark 2, 3, or 4 chemicals, or List Translator screening showing no LT-1 hazards.

Cradle to Cradle v3 Gold/Platinum , or v2 Gold/Platinum.

REACH Substances of Very High Concern (SVHC) avoidance — manufacturer verifies the product contains no Authorization-list chemicals.

Living Building Challenge (LBC) Red List free or LBC Declaration.

The optimized product cost must total at least 25% of permanently installed products.

Reading a Counting Question

LEED counts permanently installed products. Furniture is included for the New Construction (NC) Healthcare projects but not for most other BD+C ratings. MEP equipment is excluded from all BPDO calculations.

Worked Example

A project has 100 permanently installed products:

  • 15 have product-specific EPDs (= 15 products)
  • 10 have industry-wide EPDs (= 10 × ½ = 5 products)
  • Total counted: 20 products

If those 25 manufacturers represent at least 5 unique companies, the project earns the EPD disclosure point.

Exam Cue

Watch for the half-credit rule for industry-wide EPDs and the double-credit (local) multiplier in Sourcing. Both show up in calculation questions.