Study guide

5.2 Outdoor and Indoor Water Use Reduction Credits

LEED AP Building Design + Construction BD+C

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Introduction & Exam Overview

1.1 Current Exam Facts 1.2 How to Use This Guide

2 Chapter 2: Integrative Process

2.1 Integrative Process Philosophy and Workflow 2.2 Integrative Process Credit (IP) 2.3 Prerequisites and Project Setup 2.4 Certification Levels and Scorecard

3 Chapter 3: Location & Transportation + Surroundings

3.1 LEED for Neighborhood Development Location 3.2 Sensitive Land Protection & High Priority Site 3.3 Surrounding Density and Diverse Uses 3.4 Access to Quality Transit 3.5 Bicycle Facilities, Reduced Parking, Green Vehicles 3.6 Building Surroundings and Joint Use

4 Chapter 4: Sustainable Sites (SS)

4.1 SS Prerequisite: Construction Activity Pollution Prevention 4.2 Site Assessment and Site Development 4.3 Open Space and Rainwater Management 4.4 Heat Island Reduction 4.5 Light Pollution Reduction

5 Chapter 5: Water Efficiency (WE)

5.1 WE Prerequisites 5.2 Outdoor and Indoor Water Use Reduction Credits 5.3 Cooling Tower Water Use, Process Water, and Metering 5.4 Non-Potable and Reclaimed Water Strategies

6 Chapter 6: Energy & Atmosphere (EA)

6.1 EA Prerequisites 6.2 Optimize Energy Performance 6.3 Enhanced Commissioning 6.4 Advanced Energy Metering and Grid Harmonization 6.5 Renewable Energy and Carbon Offsets 6.6 ASHRAE 90.1-2016 Fundamentals

7 Chapter 7: Materials & Resources (MR)

7.1 MR Prerequisites 7.2 Building Life-Cycle Impact Reduction (BLIR) 7.3 Building Product Disclosure and Optimization (BPDO) 7.4 Construction and Demolition Waste Management 7.5 PBT Source Reduction and Furniture Material

8 Chapter 8: Indoor Environmental Quality (EQ)

8.1 EQ Prerequisites 8.2 Enhanced IAQ Strategies and Low-Emitting Materials 8.3 Construction IAQ Management and Assessment 8.4 Thermal Comfort 8.5 Interior Lighting and Daylight 8.6 Quality Views and Acoustic Performance

9 Chapter 9: Innovation, Regional Priority & Project Types

9.1 Innovation Credits 9.2 Regional Priority Credits 9.3 BD+C Project Types and Scope 9.4 Project Registration, Documentation, and Certification Process 9.5 Last-Minute Exam Tips

5.2 Outdoor and Indoor Water Use Reduction Credits

Key Takeaways Explain This Topic AI

WE Credit: Outdoor Water Use Reduction earns 1 point for a 50% reduction from the calculated baseline and 2 points for a 100% reduction (no potable water used for irrigation).

WE Credit: Indoor Water Use Reduction earns 1-6 points on a sliding scale starting at 25% reduction (1 point) and reaching 50% reduction (6 points) below the EPAct 1992 baseline.

Indoor water calculations multiply each fixture's design flow rate by usage frequency (duration × daily uses) and FTE plus visitor occupancy, then sum across fixture groups for both baseline and design cases.

Process water for Energy Star-rated dishwashers, clothes washers, ice machines, and food steamers can contribute to additional indoor reductions but is calculated separately from fixture water.

WaterSense-labeled fixtures, dual-flush valves, waterless or pint urinals, and metered or sensor faucets are the highest-leverage indoor strategies for moving from the 20% prerequisite to the 6-point credit.

Last updated: May 2026

From Prerequisite to Credit: Going Beyond the Floor

The two reduction credits reward projects that go beyond the 20%/30% prerequisite thresholds. Together they account for 8 of the 11 WE points in LEED v4 BD+C — the largest single concentration of points in the category.

WE Credit: Outdoor Water Use Reduction (1-2 Points)

This credit uses the same EPA WaterSense Water Budget Tool methodology as the prerequisite, but raises the bar.

  • Reduction from baseline LWR Points
  • 50% 1
  • 100% (no potable water used for irrigation) 2

The baseline landscape water requirement (LWR) is calculated using local evapotranspiration and the project's actual plant palette. Beyond-prerequisite strategies stack:

Replace remaining turf with native and adapted ground cover .

Use drip or subsurface drip irrigation (efficiency ≥0.85) rather than spray (~0.625).

Add rain sensors, soil moisture sensors, or weather-based smart controllers (must be WaterSense-labeled controller to claim the higher efficiency assumption).

Use captured rainwater, graywater, municipal reclaimed water, or HVAC condensate for irrigation. Any of these non-potable sources reduce potable water demand to zero and earn the 2-point threshold.

WE Credit: Indoor Water Use Reduction (1-6 Points)

  • Reduction from EPAct 1992 baseline Points
  • 25% 1
  • 30% 2
  • 35% 3
  • 40% 4
  • 45% 5
  • 50% 6

The sliding scale rewards each additional 5% step.

The Calculation Methodology

For each fixture group:

Daily fixture water use = flow rate × duration × daily uses per occupant × number of occupants

For flush fixtures (water closets, urinals), "flow rate × duration" collapses to gallons per flush (gpf) . For flow fixtures (faucets, showers), it's gpm × seconds ÷ 60 .

LEED uses full-time equivalent (FTE) occupants plus transient visitors . Default usage assumptions from the reference guide (per occupant per day):

  • Fixture Female FTE Male FTE Visitor
  • Water closet 3 uses 1 use 0.5 use
  • Urinal 0 2 uses 0.1 use
  • Lavatory faucet 3 uses × 15 sec 3 uses × 15 sec 0.5 use × 15 sec
  • Shower 0.1 use × 480 sec 0.1 use × 480 sec 0
  • Kitchen sink 1 use × 15 sec 1 use × 15 sec 0

A worked baseline example for 100 FTE occupants (50 female, 50 male) and 20 daily visitors :

  • Baseline water closets: (50 × 3 + 50 × 1 + 20 × 0.5) × 1.6 gpf = 336 gal/day
  • Design with 1.28 gpf WaterSense closets: same uses × 1.28 = 268.8 gal/day
  • Closet reduction = (336 − 268.8) ÷ 336 = 20%

That closet-only swap only matches the prerequisite. To reach 30-50%, the team typically combines:

  • Dual-flush water closets (0.8 gpf reduced flush / 1.28 gpf full)
  • Pint urinals (0.125 gpf) or waterless urinals (0 gpf)
  • 0.5 gpm public lavatory faucets (already baseline) plus sensor or metering valves
  • 1.5 gpm WaterSense showerheads
  • 1.5 gpm kitchen faucet aerators
  • Process Water Contribution

Separate from fixture water, process water for appliances can support additional indoor savings:

  • Appliance Energy Star / target
  • Residential dishwasher ≤3.5 gal/cycle
  • Commercial dishwasher varies by type (door-type ≤0.95 gal/rack)
  • Residential clothes washer Water Factor (WF) ≤4.3
  • Commercial clothes washer WF ≤4.0
  • Ice machine Air-cooled, ≤25 gal per 100 lb ice
  • Food steamer Connectionless or boilerless

Process water from these appliances is calculated against an Energy Star or LEED-specified baseline and folded into the indoor reduction total when applicable.

  • Strategy Stack to Reach 50% Prerequisite (20%)
  • + WaterSense lavatories and showers (~3-5%)
  • + Dual-flush water closets (~5-7%)
  • + Pint or waterless urinals (~5-8%)
  • + Sensor/metering valves on public faucets (~2-3%)
  • + Energy Star process equipment (~2-4%)
  • = 35-47% (4-5 points)

Projects targeting all 6 points (50%) typically combine the above with non-potable flushing water (graywater or rainwater) — covered in Section 5.4.