Study guide
12.3 Boiler Thermal Efficiency, Fuel Consumption, Heat Input & Factor of Evaporation
Massachusetts Boiler Operator Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Massachusetts Boiler Laws, Regulations & Licensing
1.1 Department of Fire Services Oversight, M.G.L. c. 146 Statutes & 522 CMR Rules 1.2 Massachusetts License Tiers, Horsepower Limits & Statutory Prerequisites 1.3 Plant Attendance Tiers, Daily Logbooks & Certificate of Inspection Protocols
2 Chapter 2: Boiler Principles, Construction & ASME Codes
2.1 Thermodynamics, Latent Heat & Properties of Saturated/Superheated Steam 2.2 Firetube Boiler Construction, Stays & Structural Elements 2.3 Watertube Boiler Configurations, Electric Boilers & ASME Code Stamping
3 Chapter 3: Boiler Safety Devices & Relief Valves
3.1 Safety Valve Operating Mechanics, Code Installation & Accumulation Testing 3.2 Safety Valve Relieving Capacity, Sizing Calculations & Blowdown Adjustments 3.3 Low-Water Fuel Cutoffs (LWCO), Water Columns & Daily Blowdown Protocols
4 Chapter 4: Feedwater Systems & Boiler Water Level Control
4.1 Water Columns, Gauge Glasses & Try Cocks 4.2 Feedwater Piping, Stop/Check Valve Configurations & Steam Injectors 4.3 Feedwater Pumps, Automatic Water Feeders & Deaerating Feed Tanks
5 Chapter 5: Boiler Water Treatment & Chemistry Control
5.1 Feedwater Impurities, Water Hardness & Scale Formation 5.2 Dissolved Oxygen Pitting, Acidic Corrosion & Caustic Embrittlement 5.3 Internal Chemical Treatment: Phosphates, Chelants, Sulfite & Amines 5.4 Water Testing, Specific Conductance & Continuous/Bottom Blowdown Control
6 Chapter 6: Fuels, Combustion & Burner Systems
6.1 Combustion Principles, Stoichiometry, Flue Gas Analysis & Excess Air 6.2 Fuel Oil Grades, Storage, Preheating & Burner Atomization Methods 6.3 Natural Gas and Propane Fuel Trains, Pressure Regulators & Atmospheric/Power Burners
7 Chapter 7: Combustion Safeguards, Flame Scanners & Draft Systems
7.1 Flame Scanners, Flame Rectification & Optical Safeguard Sensors 7.2 Burner Management Systems (BMS), Pre-Purge Sequences & Safety Interlocks 7.3 Draft Principles, Natural Draft, Forced Draft, Induced Draft & Draft Regulators
8 Chapter 8: Steam Piping, Superheaters & Steam Traps
8.1 Convection and Radiant Superheaters, Desuperheaters & Attemperation Control 8.2 Steam Trap Operating Principles, Thermostatic/Thermodynamic/Mechanical Traps & Diagnostic Testing 8.3 Main Steam Piping, Non-Return Stop Valves, Expansion Loops & Water Hammer Prevention
9 Chapter 9: Boiler Operations, Routine Maintenance & Layup
9.1 Cold Boiler Startup Procedures, Warming Lines & Thermal Stress Mitigation 9.2 Normal Operating Routines, Shift Turnover Logs & Housekeeping 9.3 Normal Boiler Shutdown, Wet Layup & Dry Layup Procedures
10 Chapter 10: Emergency Procedures & Casualty Control
10.1 Low-Water Emergencies, Immediate Response Protocols & Prevention 10.2 Boiler Tube Ruptures, Carryover, Priming & Foaming 10.3 Furnace Explosions, Flarebacks & Safety Valve Failure Emergencies
11 Chapter 11: Boiler Inspections, Maintenance & Code Repairs
11.1 Preparing for State Internal/External Inspections & Confined Space Safety (OSHA 1910.146) 11.2 Hydrostatic Pressure Testing Procedures, Water Temperature Rules & Test Pressures 11.3 Refractory Maintenance, Soot Blowing, Fireside Washing & Troubleshooting
12 Chapter 12: Power Plant Mathematics & Applied Engineering Calculations
12.1 Boiler Horsepower (BHP), Heating Surface Area & Equivalent Evaporation Calculations 12.2 Safety Valve Relieving Capacity, Orifice Sizing & Accumulation Test Calculations 12.3 Boiler Thermal Efficiency, Fuel Consumption, Heat Input & Factor of Evaporation
12.3 Boiler Thermal Efficiency, Fuel Consumption, Heat Input & Factor of Evaporation
Key Takeaways Explain This Topic AI
Boiler thermal efficiency is evaluated under ASME PTC 4 via two distinct standards: the Direct (Input-Output) Method (η = [Energy in Steam] / [Energy in Fuel] x 100%) and the Indirect (Heat Loss) Method (η = 100% - Sum of Losses).
The Direct Method directly tracks fuel flow and steam generation; however, flowmeter inaccuracies directly degrade results, whereas the Indirect Method isolates specific thermodynamic losses (dry flue gas, hydrogen moisture, unburned carbon, casing radiation) to diagnose operational defects.
Hourly fuel consumption is calculated from total steam energy demand, fuel Higher Heating Value (HHV), and thermal efficiency: Fuel Flow = [Steam Flow x (h_s - h_f)] / [HHV x η].
Cycles of Concentration (COC = Boiler Chlorides / Feedwater Chlorides) determine blowdown requirements; continuous blowdown mass flow equals Steam Flow / (COC - 1), while percent blowdown equals 100% / COC.
Under ASME Section I (PG-99) and Massachusetts 522 CMR, newly installed power boilers or major welded alterations require a hydrostatic strength test at 1.50 times the Maximum Allowable Working Pressure (1.50 x MAWP) with water temperatures strictly maintained between 70°F and 120°F.
Last updated: September 2026
12.3 Boiler Thermal Efficiency, Fuel Consumption, Heat Input & Factor of Evaporation
Quick Summary: In modern stationary engineering, maximizing thermal efficiency directly governs operational profitability and environmental compliance. Under ASME PTC 4 (Fired Steam Generators) , efficiency is evaluated through two distinct methodologies: the Direct Method (Input-Output) , which measures useful heat absorbed by steam divided by total chemical energy supplied by fuel, and the Indirect Method (Heat Loss) , which subtracts individual thermodynamic energy losses (such as dry flue gas loss and moisture from hydrogen combustion) from 100%. Operating engineers use these efficiency values alongside fuel Higher Heating Values (HHV) to determine exact hourly fuel consumption in gallons of oil or therms of natural gas. In water management, Cycles of Concentration (COC) govern continuous surface blowdown rates to prevent scale and foaming, while code verification requires calculating hydrostatic test pressures (1.50 x MAWP) for new construction and major NBIC repairs.
1. Boiler Thermal Efficiency: ASME PTC 4 Direct vs. Indirect Methods
Boiler thermal efficiency measures the effectiveness with which a steam generator transfers the chemical energy stored in fuel into thermodynamic energy in water and steam. ASME Performance Test Code 4 ( ASME PTC 4 ) establishes two rigorous testing procedures:
The Direct Method (Input-Output Method)
The Direct Method measures bulk gross energy outputs and inputs over a steady-state test window: Thermal Efficiency ( η direct ) = ( Energy Absorbed by Working Fluid Chemical Energy Supplied by Fuel ) × 100 % \text{Thermal Efficiency } (\eta_{\text{direct}}) = \left(\frac{\text{Energy Absorbed by Working Fluid}}{\text{Chemical Energy Supplied by Fuel}}\right) \times 100\% Thermal Efficiency ( η direct ) = ( Chemical Energy Supplied by Fuel Energy Absorbed by Working Fluid ) × 100% η direct = [ W s × ( h s − h f ) W f × H H V ] × 100 % \eta_{\text{direct}} = \left[\frac{W_s \times (h_s - h_f)}{W_f \times HHV}\right] \times 100\% η direct = [ W f × HH V W s × ( h s − h f ) ] × 100%
Where:
W s = Total steam mass flow rate produced (lb/hr) W_s = \text{Total steam mass flow rate produced (lb/hr)} W s = Total steam mass flow rate produced (lb/hr) .
h s = Enthalpy of steam leaving boiler outlet (Btu/lb) h_s = \text{Enthalpy of steam leaving boiler outlet (Btu/lb)} h s = Enthalpy of steam leaving boiler outlet (Btu/lb) .
h f = Enthalpy of feedwater entering boiler economizer/drum (Btu/lb) h_f = \text{Enthalpy of feedwater entering boiler economizer/drum (Btu/lb)} h f = Enthalpy of feedwater entering boiler economizer/drum (Btu/lb) .
W f = Fuel firing mass or volumetric flow rate per hour (lb/hr, gal/hr, or scfh) W_f = \text{Fuel firing mass or volumetric flow rate per hour (lb/hr, gal/hr, or scfh)} W f = Fuel firing mass or volumetric flow rate per hour (lb/hr, gal/hr, or scfh) .
H H V = Higher Heating Value of fuel (Btu/lb, Btu/gal, or Btu/scf) HHV = \text{Higher Heating Value of fuel (Btu/lb, Btu/gal, or Btu/scf)} HH V = Higher Heating Value of fuel (Btu/lb, Btu/gal, or Btu/scf) .
The Indirect Method (Heat Loss Method)
The Indirect Method determines efficiency by identifying and quantifying all individual heat losses departing the system, expressing each as a percentage of total fuel heat input: η indirect = 100 % − ∑ Heat Losses ( % ) \eta_{\text{indirect}} = 100\% - \sum \text{Heat Losses } (\%) η indirect = 100% − ∑ Heat Losses ( % ) η indirect = 100 % − ( L 1 + L 2 + L 3 + L 4 + L 5 + L 6 + L 7 ) \eta_{\text{indirect}} = 100\% - (L_1 + L_2 + L_3 + L_4 + L_5 + L_6 + L_7) η indirect = 100% − ( L 1 + L 2 + L 3 + L 4 + L 5 + L 6 + L 7 )
Loss Parameter Engineering Description & Mechanism Typical Magnitude
L 1 L_1 L 1 : Dry Flue Gas Loss Sensible heat carried away by non-condensable combustion gases ( N 2 , C O 2 , O 2 N_2, CO_2, O_2 N 2 , C O 2 , O 2 ). Governed by stack temperature ( T stack T_{\text{stack}} T stack ) and excess air level. Largest single controllable loss. 4.0% – 10.0%
L 2 L_2 L 2 : Moisture from Hydrogen Combustion Latent and sensible heat lost in water vapor ( H 2 O H_2O H 2 O ) formed when hydrogen atoms in hydrocarbon fuel oxidize ( 2 H 2 + O 2 → 2 H 2 O 2H_2 + O_2 \rightarrow 2H_2O 2 H 2 + O 2 → 2 H 2 O ). Higher in natural gas ( C H 4 CH_4 C H 4 ) than oil/coal. 5.0% – 11.0%
L 3 L_3 L 3 : Moisture in Fuel Heat expended to vaporize liquid water naturally entrained in fuel (significant in high-moisture coal, wood, and residual heavy fuel oil). 0.2% – 2.0%
L 4 L_4 L 4 : Moisture in Combustion Air Sensible heat absorbed by water vapor present in ambient combustion air humidity. 0.1% – 0.5%
L 5 L_5 L 5 : Incomplete Combustion (CO) Chemical energy lost when carbon burns partially to carbon monoxide ( C O CO CO ) rather than carbon dioxide ( C O 2 CO_2 C O 2 ), losing 10 , 160 Btu 10,160\text{ Btu} 10 , 160 Btu per pound of carbon unoxidized. 0.1% – 1.0%
L 6 L_6 L 6 : Radiation & Convection Casing Loss Heat radiated and convected from hot boiler casing walls, drum heads, and insulation into boiler room air. 0.3% – 1.5%
L 7 L_7 L 7 : Blowdown & Unaccounted Losses Sensible heat discarded in hot continuous boiler water blowdown, soot blower steam consumption, and unburned combustible fly ash. 0.5% – 2.5%
Direct vs. Indirect Comparison
Direct Method Advantages: Conceptually straightforward; requires only fuel metering and steam flow measurement.
Direct Method Disadvantages: Highly sensitive to flowmeter errors. If a steam orifice meter drifts high by 3%, calculated efficiency drifts high by 3%. It provides zero diagnostic data regarding why efficiency is low.
Indirect Method Advantages: Highly accurate. A 5% error in measuring dry flue gas loss affects calculated overall efficiency by less than 0.3%. It pinpoints exact operational defects (such as fouled tubes raising stack temperature, or torn burner seals leaking excess air).
2. Fuel Consumption Calculations
Operating engineers frequently calculate expected fuel consumption to project operating budgets, verify burner firing setups, or verify environmental air emissions permits.
The Master Fuel Consumption Formula
Rearranging the Direct Efficiency equation to solve for fuel consumption rate ( W f W_f W f ): W f = W s × ( h s − h f ) HHV × η W_f = \frac{W_s \times (h_s - h_f)}{\text{HHV} \times \eta} W f = HHV × η W s × ( h s − h f )
Fuel Heating Values (HHV) in Power Plant Practice
No. 2 Fuel Oil (Light Distillate / Diesel): 138 , 000 to 141 , 000 Btu/gal 138,000\text{ to } 141,000\text{ Btu/gal} 138 , 000 to 141 , 000 Btu/gal (Standard design benchmark: 140,000 Btu/gal ).
No. 6 Fuel Oil (Heavy Residual / Bunker C): 148 , 000 to 152 , 000 Btu/gal 148,000\text{ to } 152,000\text{ Btu/gal} 148 , 000 to 152 , 000 Btu/gal (Standard design benchmark: 150,000 Btu/gal ).
Natural Gas: 1 , 000 to 1 , 050 Btu per standard cubic foot (scf) 1,000\text{ to } 1,050\text{ Btu per standard cubic foot (scf)} 1 , 000 to 1 , 050 Btu per standard cubic foot (scf) (Standard design benchmark: 1,000 Btu/scf ).
Therms of Natural Gas: 1 Therm = 100 , 000 Btu 1\text{ Therm} = 100,000\text{ Btu} 1 Therm = 100 , 000 Btu .
Fuel Oil Consumption Formula (Gallons per Hour) Fuel Oil Consumption (gal/hr) = W s × ( h s − h f ) HHV (Btu/gal) × η \text{Fuel Oil Consumption (gal/hr)} = \frac{W_s \times (h_s - h_f)}{\text{HHV (Btu/gal)} \times \eta} Fuel Oil Consumption (gal/hr) = HHV (Btu/gal) × η W s × ( h s − h f )
Natural Gas Consumption Formula (Therms and SCF per Hour) Natural Gas (Therms/hr) = W s × ( h s − h f ) 100 , 000 Btu/Therm × η \text{Natural Gas (Therms/hr)} = \frac{W_s \times (h_s - h_f)}{100,000\text{ Btu/Therm} \times \eta} Natural Gas (Therms/hr) = 100 , 000 Btu/Therm × η W s × ( h s − h f ) Natural Gas (scfh) = W s × ( h s − h f ) 1 , 000 Btu/scf × η \text{Natural Gas (scfh)} = \frac{W_s \times (h_s - h_f)}{1,000\text{ Btu/scf} \times \eta} Natural Gas (scfh) = 1 , 000 Btu/scf × η W s × ( h s − h f )
3. Heat Input, Firing Rate & Factor of Evaporation Relationships
Boiler firing controls and burner modulating motors operate on total gross heat input ( Q input Q_{\text{input}} Q input ). To calculate required heat input from developed boiler horsepower or equivalent evaporation: Q output = W s × ( h s − h f ) = E E × 970.3 = Developed BHP × 33 , 475 Q_{\text{output}} = W_s \times (h_s - h_f) = EE \times 970.3 = \text{Developed BHP} \times 33,475 Q output = W s × ( h s − h f ) = EE × 970.3 = Developed BHP × 33 , 475 Q input = Q output η = Developed BHP × 33 , 475 η Q_{\text{input}} = \frac{Q_{\text{output}}}{\eta} = \frac{\text{Developed BHP} \times 33,475}{\eta} Q input = η Q output = η Developed BHP × 33 , 475
Applying fuel Higher Heating Value: Fuel Flow = Developed BHP × 33 , 475 HHV × η \text{Fuel Flow} = \frac{\text{Developed BHP} \times 33,475}{\text{HHV} \times \eta} Fuel Flow = HHV × η Developed BHP × 33 , 475
Rule of Thumb: A 100 BHP boiler operating at 80% efficiency requires: Q input = 100 × 33 , 475 0.80 = 4 , 184 , 375 Btu/hr Q_{\text{input}} = \frac{100 \times 33,475}{0.80} = 4,184,375\text{ Btu/hr} Q input = 0.80 100 × 33 , 475 = 4 , 184 , 375 Btu/hr
Burning No. 2 oil (140,000 Btu/gal), it consumes 4 , 184 , 375 / 140 , 000 ≈ 29.89 gal/hr 4,184,375 / 140,000 \approx 29.89\text{ gal/hr} 4 , 184 , 375/140 , 000 ≈ 29.89 gal/hr , or roughly 0.3 gallons per hour per boiler horsepower .
4. Water Chemistry Math: Cycles of Concentration and Blowdown Rates
As water evaporates in a steam boiler, pure water vapor leaves the steam drum, leaving non-volatile dissolved mineral solids (calcium, magnesium, silica, chlorides) behind. Without blowdown, dissolved solids would rapidly concentrate to saturation levels, causing scale deposition, foaming, erratic water level swings, and corrosive carryover into steam headers.
Cycles of Concentration (COC)
The Cycles of Concentration (COC) measures how many times dissolved mineral solids have been concentrated within the boiler water relative to the incoming feedwater: C O C = Concentration of Mineral Tracer in Boiler Water Concentration of Mineral Tracer in Feedwater COC = \frac{\text{Concentration of Mineral Tracer in Boiler Water}}{\text{Concentration of Mineral Tracer in Feedwater}} COC = Concentration of Mineral Tracer in Feedwater Concentration of Mineral Tracer in Boiler Water
Operating engineers select non-volatile chemical tracers that do not precipitate, flash into steam, or degrade under boiler temperatures. The two most common tracers are Chlorides ( C l − Cl^- C l − ) and Silica ( S i O 2 SiO_2 S i O 2 ) : C O C = Boiler Water Chlorides (ppm) Feedwater Chlorides (ppm) = Boiler Water Silica (ppm) Feedwater Silica (ppm) COC = \frac{\text{Boiler Water Chlorides (ppm)}}{\text{Feedwater Chlorides (ppm)}} = \frac{\text{Boiler Water Silica (ppm)}}{\text{Feedwater Silica (ppm)}} COC = Feedwater Chlorides (ppm) Boiler Water Chlorides (ppm) = Feedwater Silica (ppm) Boiler Water Silica (ppm)
(Note: Total Dissolved Solids [TDS] via electrical conductivity in micromhos/cm is also widely used, adjusting for neutralizing amines).
Blowdown Rate as a Percentage of Feedwater Flow
By steady-state mineral conservation mass balance (Solids Entering in Feedwater = Solids Leaving in Blowdown): W f w × C f w = W b d × C b w W_{fw} \times C_{fw} = W_{bd} \times C_{bw} W f w × C f w = W b d × C b w Blowdown Fraction = W b d W f w = C f w C b w = 1 C O C \text{Blowdown Fraction} = \frac{W_{bd}}{W_{fw}} = \frac{C_{fw}}{C_{bw}} = \frac{1}{COC} Blowdown Fraction = W f w W b d = C b w C f w = COC 1 Blowdown Rate ( % of Feedwater ) = ( 1 C O C ) × 100 % \text{Blowdown Rate } (\% \text{ of Feedwater}) = \left(\frac{1}{COC}\right) \times 100\% Blowdown Rate ( % of Feedwater ) = ( COC 1 ) × 100%
Rule of Thumb: At 10 cycles of concentration, blowdown equals 10 % 10\% 10% of feedwater. At 20 cycles of concentration, blowdown equals 5 % 5\% 5% of feedwater.
Continuous Blowdown Mass Flow Rate ( W b d W_{bd} W b d ) Based on Steam Flow ( W s W_s W s )
In practice, power plants meter steam production ( W s W_s W s ) rather than feedwater flow ( W f w W_{fw} W f w ). Since W f w = W s + W b d W_{fw} = W_s + W_{bd} W f w = W s + W b d , substituting yields the master equation for continuous blowdown flow: ( W s + W b d ) × C f w = W b d × C b w (W_s + W_{bd}) \times C_{fw} = W_{bd} \times C_{bw} ( W s + W b d ) × C f w = W b d × C b w W s × C f w + W b d × C f w = W b d × C b w W_s \times C_{fw} + W_{bd} \times C_{fw} = W_{bd} \times C_{bw} W s × C f w + W b d × C f w = W b d × C b w W s × C f w = W b d × ( C b w − C f w ) W_s \times C_{fw} = W_{bd} \times (C_{bw} - C_{fw}) W s × C f w = W b d × ( C b w − C f w )
Dividing both sides by C f w C_{fw} C f w : W s = W b d × ( C b w C f w − 1 ) = W b d × ( C O C − 1 ) W_s = W_{bd} \times \left(\frac{C_{bw}}{C_{fw}} - 1\right) = W_{bd} \times (COC - 1) W s = W b d × ( C f w C b w − 1 ) = W b d × ( COC − 1 )
Solving for blowdown flow rate ( W b d W_{bd} W b d ): W b d = W s C O C − 1 W_{bd} = \frac{W_s}{COC - 1} W b d = COC − 1 W s
Where:
W b d = Continuous blowdown mass flow rate (lb/hr) W_{bd} = \text{Continuous blowdown mass flow rate (lb/hr)} W b d = Continuous blowdown mass flow rate (lb/hr) .
W s = Total steam flow rate (lb/hr) W_s = \text{Total steam flow rate (lb/hr)} W s = Total steam flow rate (lb/hr) .
C O C = Cycles of concentration (dimensionless) COC = \text{Cycles of concentration (dimensionless)} COC = Cycles of concentration (dimensionless) .
5. Hydrostatic Test Pressure Calculations & Code Rules
A hydrostatic test subjects a boiler pressure vessel to water pressure significantly higher than its normal operating setpoint to verify structural integrity, prove welded repair strength, and detect weeping leaks without the explosive pneumatic risks associated with compressed gases.
Statutory Test Ratios Under ASME Section I and Massachusetts 522 CMR +-------------------------------------------------------------------------+
- | STATUTORY HYDROSTATIC TEST PRESSURES |
- | |
- | • New Construction / Acceptance Test: 1.50 x MAWP |
- | • Major Welded Alteration (NBIC / NB-23): 1.50 x MAWP |
- | • In-Service Periodic Re-Test: 1.25 x MAWP (or 1.50 x MAWP |
- | at Inspector's Discretion) |
- +-------------------------------------------------------------------------+
New Boiler Construction & Acceptance (ASME Section I, PG-99): P hydro = 1.50 × MAWP P_{\text{hydro}} = 1.50 \times \text{MAWP} P hydro = 1.50 × MAWP Every newly constructed ASME Section I power boiler must withstand a shop or field hydrostatic test conducted at 1.50 times the Maximum Allowable Working Pressure .
Major Welded Repairs and Alterations (NBIC Part 3): Any major structural repair (such as replacing waterwall panels, drum shell inserts, or re-tubing) executed under a National Board 'R' Certificate of Authorization requires a hydrostatic test at 1.50 × MAWP 1.50 \times \text{MAWP} 1.50 × MAWP , witnessed by an Authorized Inspector.
In-Service Re-Testing (NBIC Part 2 / 522 CMR): For periodic inservice integrity testing of older operating boilers where a full 1.50x test could overstress aged metal, the inspector may specify 1.25 × MAWP 1.25 \times \text{MAWP} 1.25 × MAWP .
Mandatory Hydrostatic Test Safety Protocols
Water Temperature Window (70°F to 120°F): Under ASME Section I (PG-99.1), the water used for hydrostatic testing must be maintained at not less than 70°F (21°C) to eliminate the hazard of brittle fracture of heavy steel shells and drum plates, and not more than 120°F (49°C) to prevent thermal burns to inspectors and prevent vapor formation that obscures fine leaks.
Air Venting: During filling, the boiler air cock at the highest point of the steam drum must remain wide open until solid water discharges freely, proving that all trapped air pockets are purged. Trapped air compresses under pressure, storing explosive pneumatic energy that defeats the safety intent of a hydrostatic test.
Safety Valve Isolation: Safety valves must NEVER be held closed by tightening down on the compression adjusting screw, as this alters calibrated spring pitch and ruins the valve. Instead, safety valves must be removed and replaced with blind flanges , or secured using calibrated manufacturer test gags tightened only hand-snug.
- 6. Step-by-Step Worked Problems: Combustion & Operations
- Worked Problem 1: Fuel Oil Firing Rate
Problem: A high-pressure watertube boiler generates 45,000 lb/hr of dry saturated steam at 200 psig (saturation enthalpy h s = 1 , 199.3 Btu/lb h_s = 1,199.3\text{ Btu/lb} h s = 1 , 199.3 Btu/lb ). Feedwater is supplied from an open deaerating heater at 220°F ( h f = 188.1 Btu/lb h_f = 188.1\text{ Btu/lb} h f = 188.1 Btu/lb ). The boiler burns No. 2 fuel oil having a Higher Heating Value of 140,000 Btu/gallon . A recent ASME PTC 4 combustion test established the boiler's overall operating thermal efficiency at 82% ( 0.82 0.82 0.82 ).
Determine:
The useful heat absorbed by the steam per hour ( Q output Q_{\text{output}} Q output ).
The total fuel heat energy input required per hour ( Q input Q_{\text{input}} Q input ).
The fuel oil consumption rate in gallons per hour (gph) .
The fuel oil consumption rate in gallons per day assuming continuous 24-hour full-load operation.
Step 1: Calculate useful thermal energy absorbed by steam ( Q output Q_{\text{output}} Q output ) q = h s − h f = 1 , 199.3 Btu/lb − 188.1 Btu/lb = 1 , 011.2 Btu/lb q = h_s - h_f = 1,199.3\text{ Btu/lb} - 188.1\text{ Btu/lb} = 1,011.2\text{ Btu/lb} q = h s − h f = 1 , 199.3 Btu/lb − 188.1 Btu/lb = 1 , 011.2 Btu/lb Q output = W s × q = 45 , 000 lb/hr × 1 , 011.2 Btu/lb = 45 , 504 , 000 Btu/hr Q_{\text{output}} = W_s \times q = 45,000\text{ lb/hr} \times 1,011.2\text{ Btu/lb} = 45,504,000\text{ Btu/hr} Q output = W s × q = 45 , 000 lb/hr × 1 , 011.2 Btu/lb = 45 , 504 , 000 Btu/hr
Step 2: Calculate total fuel energy input required ( Q input Q_{\text{input}} Q input ) Q input = Q output η = 45 , 504 , 000 Btu/hr 0.82 = 55 , 492 , 683 Btu/hr Q_{\text{input}} = \frac{Q_{\text{output}}}{\eta} = \frac{45,504,000\text{ Btu/hr}}{0.82} = 55,492,683\text{ Btu/hr} Q input = η Q output = 0.82 45 , 504 , 000 Btu/hr = 55 , 492 , 683 Btu/hr
Step 3: Calculate hourly fuel oil consumption Fuel Oil (gal/hr) = Q input HHV = 55 , 492 , 683 Btu/hr 140 , 000 Btu/gal = 396.38 gal/hr ≈ 396.4 gph \text{Fuel Oil (gal/hr)} = \frac{Q_{\text{input}}}{\text{HHV}} = \frac{55,492,683\text{ Btu/hr}}{140,000\text{ Btu/gal}} = 396.38\text{ gal/hr} \approx 396.4\text{ gph} Fuel Oil (gal/hr) = HHV Q input = 140 , 000 Btu/gal 55 , 492 , 683 Btu/hr = 396.38 gal/hr ≈ 396.4 gph
Step 4: Calculate 24-hour daily consumption Daily Consumption = 396.38 gal/hr × 24 hr/day = 9 , 513 gallons/day \text{Daily Consumption} = 396.38\text{ gal/hr} \times 24\text{ hr/day} = 9,513\text{ gallons/day} Daily Consumption = 396.38 gal/hr × 24 hr/day = 9 , 513 gallons/day
Worked Problem 2: Natural Gas Firing Rate
Problem: The facility evaluates converting the boiler above to natural gas firing. With clean burner setup and an economizer, natural gas thermal efficiency is projected at 84% ( 0.84 0.84 0.84 ). Steam conditions and generation rate remain identical ( Q output = 45 , 504 , 000 Btu/hr Q_{\text{output}} = 45,504,000\text{ Btu/hr} Q output = 45 , 504 , 000 Btu/hr ). Determine the natural gas consumption rate in Therms per hour and Standard Cubic Feet per hour (scfh) assuming gas HHV of 1 , 025 Btu/scf 1,025\text{ Btu/scf} 1 , 025 Btu/scf .
Step 1: Calculate total fuel energy input required ( Q input Q_{\text{input}} Q input ) Q input = 45 , 504 , 000 Btu/hr 0.84 = 54 , 171 , 429 Btu/hr Q_{\text{input}} = \frac{45,504,000\text{ Btu/hr}}{0.84} = 54,171,429\text{ Btu/hr} Q input = 0.84 45 , 504 , 000 Btu/hr = 54 , 171 , 429 Btu/hr
Step 2: Calculate gas consumption in Therms per hour Therms/hr = 54 , 171 , 429 Btu/hr 100 , 000 Btu/Therm = 541.71 Therms/hr \text{Therms/hr} = \frac{54,171,429\text{ Btu/hr}}{100,000\text{ Btu/Therm}} = 541.71\text{ Therms/hr} Therms/hr = 100 , 000 Btu/Therm 54 , 171 , 429 Btu/hr = 541.71 Therms/hr
Step 3: Calculate volumetric gas flow in standard cubic feet per hour (scfh) Gas Flow (scfh) = 54 , 171 , 429 Btu/hr 1 , 025 Btu/scf = 52 , 850.17 scfh ≈ 52 , 850 scfh \text{Gas Flow (scfh)} = \frac{54,171,429\text{ Btu/hr}}{1,025\text{ Btu/scf}} = 52,850.17\text{ scfh} \approx 52,850\text{ scfh} Gas Flow (scfh) = 1 , 025 Btu/scf 54 , 171 , 429 Btu/hr = 52 , 850.17 scfh ≈ 52 , 850 scfh
Worked Problem 3: Continuous Blowdown Calculation
Problem: An industrial steam plant operates with a continuous steam output of 60,000 lb/hr . Water testing reveals:
Feedwater chloride concentration ( C f w C_{fw} C f w ): 12 ppm .
Maximum allowable boiler water chloride concentration ( C b w C_{bw} C b w ): 120 ppm .
Determine:
The Cycles of Concentration (COC).
The blowdown rate as a percentage of feedwater flow.
The continuous blowdown flow rate in pounds per hour (lb/hr) .
The total feedwater mass flow rate required to maintain water level in the drum.
Step 1: Calculate Cycles of Concentration (COC) C O C = C b w C f w = 120 ppm 12 ppm = 10 cycles COC = \frac{C_{bw}}{C_{fw}} = \frac{120\text{ ppm}}{12\text{ ppm}} = 10\text{ cycles} COC = C f w C b w = 12 ppm 120 ppm = 10 cycles
Step 2: Calculate blowdown percentage of feedwater % Blowdown = ( 1 C O C ) × 100 % = ( 1 10 ) × 100 % = 10.0 % \%\text{ Blowdown} = \left(\frac{1}{COC}\right) \times 100\% = \left(\frac{1}{10}\right) \times 100\% = 10.0\% % Blowdown = ( COC 1 ) × 100% = ( 10 1 ) × 100% = 10.0%
Step 3: Calculate continuous blowdown mass flow rate ( W b d W_{bd} W b d ) W b d = W s C O C − 1 = 60 , 000 lb/hr 10 − 1 = 60 , 000 lb/hr 9 = 6 , 666.67 lb/hr W_{bd} = \frac{W_s}{COC - 1} = \frac{60,000\text{ lb/hr}}{10 - 1} = \frac{60,000\text{ lb/hr}}{9} = 6,666.67\text{ lb/hr} W b d = COC − 1 W s = 10 − 1 60 , 000 lb/hr = 9 60 , 000 lb/hr = 6 , 666.67 lb/hr
Step 4: Calculate total feedwater flow required ( W f w W_{fw} W f w ) W f w = W s + W b d = 60 , 000 lb/hr + 6 , 666.67 lb/hr = 66 , 666.67 lb/hr W_{fw} = W_s + W_{bd} = 60,000\text{ lb/hr} + 6,666.67\text{ lb/hr} = 66,666.67\text{ lb/hr} W f w = W s + W b d = 60 , 000 lb/hr + 6 , 666.67 lb/hr = 66 , 666.67 lb/hr
Check: W b d W f w = 6 , 666.67 66 , 666.67 = 0.100 = 10.0 % \frac{W_{bd}}{W_{fw}} = \frac{6,666.67}{66,666.67} = 0.100 = 10.0\% W f w W b d = 66 , 666.67 6 , 666.67 = 0.100 = 10.0% . The mass balance is verified.
Worked Problem 4: Hydrostatic Test Pressure Calculation
Problem: A newly constructed industrial watertube power boiler has an ASME stamped Maximum Allowable Working Pressure (MAWP) of 250 psig .
Determine:
The required hydrostatic test pressure under ASME Section I (PG-99) and Massachusetts 522 CMR.
The required water temperature range during the test.
Solution:
Calculate required test pressure: P hydro = 1.50 × MAWP = 1.50 × 250 psig = 375.0 psig P_{\text{hydro}} = 1.50 \times \text{MAWP} = 1.50 \times 250\text{ psig} = 375.0\text{ psig} P hydro = 1.50 × MAWP = 1.50 × 250 psig = 375.0 psig
The water temperature must be maintained between 70°F and 120°F throughout the hydrostatic examination to prevent brittle fracture and eliminate inspector scalding/steaming hazards.