Study guide

2.3 Temporary Permits, Continuing Education, Apprentices & Company Exemptions (230 CMR 6.03–6.07)

Massachusetts Crane Operator Hoisting Engineer License

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Massachusetts Hoisting Law (MGL Chapter 146)

1.1 MGL Chapter 146 §§ 53–54A: The Hoisting License Mandate, Exemptions & Penalties 1.2 MGL Chapter 146 §§ 57–67: Applications, Examinations, Appeals, License Term & Renewal

2 Chapter 2: Licensing Under 230 CMR 6.00

2.1 License Classes & Restrictions Under 230 CMR 6.10 2.2 Applying, Medical Qualification, the OPSI Exam & Renewal (230 CMR 6.02) 2.3 Temporary Permits, Continuing Education, Apprentices & Company Exemptions (230 CMR 6.03–6.07)

3 Chapter 3: 230 CMR 6.00 Definitions, Operating Rules & Enforcement

3.1 230 CMR 6.01: Scope, Key Definitions, Exempt Equipment & Adopted Standards 3.2 Operating Procedures Under 230 CMR 6.08: Inspections, Attention, Signals & Stop Authority 3.3 Special Requirements Under 230 CMR 6.09: Cranes, Derricks, Pile Drivers, Forklifts & Excavators 3.4 Incident Reporting, Investigations, Discipline & Variances (230 CMR 6.11–6.13)

4 Chapter 4: Crane Types, Working Parts & Load Charts

4.1 Crane Types & Working Parts by Restriction: Lattice, Derrick, Tower, Telescopic & Hydraulic Machines 4.2 Load Chart Fundamentals: Structural Strength vs. Stability Limits 4.3 Capacity Deductions & Calculating Net Allowable Capacity 4.4 Quadrants of Operation, Working Radius & Boom Angle Dynamics

5 Chapter 5: Advanced Lift Calculations & Multi-Crane Operations

5.1 Boom Deflection, Ground Leveling & Side-Loading Hazards 5.2 Wire Rope Reeving, Parts of Line & Single-Line Pull Limits 5.3 Center of Gravity, Weight Distribution & Multi-Crane (Tandem) Lifts

6 Chapter 6: Dig Safe, Underground Utilities & Trench Safety

6.1 Massachusetts Dig Safe Law (MGL c. 82 §§ 40–40E, 220 CMR 99.00): Premarking & Notice 6.2 Utility Color Codes, the 18-Inch Safety Zone, Excavating Near Facilities & Damage Response 6.3 Trench Safety Law, Excavation Hazards, Setbacks & Utility-Strike Emergencies

7 Chapter 7: Power Lines, Ground Conditions & Weather

7.1 Power Line Safety: OSHA 1926.1408–1411, Table A & Table T 7.2 Ground Bearing Pressure, Outrigger Setup & Cribbing Sizing 7.3 Wind, Storms, Lightning, Ice & Cold: Weather Limits for Crane Work

8 Chapter 8: Rigging Principles, Slings & Hardware

8.1 Sling Types: Synthetic, Wire Rope, and Alloy Steel Chain Slings 8.2 Sling Angle Calculations & Tension Formulas 8.3 Rigging Hardware, Shackles, Hooks & Below-the-Hook Lifting Devices

9 Chapter 9: Wire Rope & Crane Inspection

9.1 Wire Rope Construction, Damage Assessment & Removal Criteria (OSHA 1926.1413) 9.2 Crane Inspections, Safety Devices & Operational Aids (230 CMR 6.08; OSHA 1926.1412, 1415, 1416)

10 Chapter 10: Hand Signals & Personnel Hoisting

10.1 Standard Hand Signals, Voice & Radio Signals and Signal Person Qualification 10.2 Crane-Suspended Personnel Platforms (230 CMR 6.09(6) & OSHA 29 CFR 1926.1431)

2.3 Temporary Permits, Continuing Education, Apprentices & Company Exemptions (230 CMR 6.03–6.07)

Key Takeaways Explain This Topic AI

A temporary permit covers only rented compact hoisting machinery with a gross vehicle weight not exceeding 10,000 pounds and is valid for no more than 14 consecutive days (230 CMR 6.03).

The first temporary permit an applicant receives in a calendar year is valid for 28 days, and no person may receive more than one temporary permit in any 45-day period.

Each Class 1 renewal requires at least two classroom hours of approved continuing education: one regulatory and industry-standard hour and one equipment-specific hour (230 CMR 6.04).

An apprentice licensee must be at least 16, registered with the Division of Apprentice Standards and operate only under direct guidance of a licensed non-apprentice (230 CMR 6.01, 6.05).

Approved in-service training for 1A, 1B or 1C company licenses requires at least four classroom hours, and program approval lasts two years (230 CMR 6.07).

Last updated: October 2026

Temporary permits for rented compact machinery (230 CMR 6.03)

A homeowner or small contractor who rents a mini excavator for a weekend may get a temporary permit instead of a license, but only from an OPSI-approved short-term rental entity .

What the permit covers

Rule Detail

Equipment Compact hoisting machinery only: gross vehicle weight not exceeding 10,000 pounds , excluding Class 1, 3 and 4 machinery

Validity No more than 14 consecutive days

First-of-year exception In any calendar year, the first temporary permit issued to an applicant is valid for 28 days ; later permits are valid for 14 days

Renewal Never renewable (MGL c. 146 § 65A)

Frequency No more than one temporary permit in any 45-day period (measured from expiration of the prior permit)

  • Applicant 18 or older with a valid driver's license
  • Carry The permit and the driver's license, on the person, while operating (MGL c. 146 § 54)

After 45 days Renting again more than 45 days after a permit expires means completing the rental entity's training and exam again

What the rental entity must do

Obtain the Office's certificate of approval , posted visibly at the rental location, by submitting a training program (instructor list, syllabus for each equipment type, curriculum covering MGL c. 146, 230 CMR 6.00, 520 CMR 14.00, OSHA 29 CFR 1926, MGL c. 82 § 40, MGL c. 82A, MGL c. 164 § 76D and 220 CMR 99.00), the exams it will use and the make and model of the training equipment.

Employ a short-term rental entity facilitator who holds a Massachusetts hoisting license of equal or greater grade than the rented machine. The facilitator signs each permit to confirm training and a passed exam. A replacement facilitator must be reported within 14 days , and no permits may be issued without one.

Issue permits on the Office's form showing the holder's name and address, the rental entity, the facilitator's printed name and signature, the issue and expiration dates, a description of the machinery, and its make and model.

Keep applications, exams and permit copies for three years , available to Inspectors.

Fraudulent issuance can lead to proceedings under MGL c. 146 § 59 and immediate suspension or revocation of the entity's approval.

Continuing education (230 CMR 6.04)

Every licensee must complete approved CE before renewal , unless the Office has approved inactive status .

Minimum hours by class

Class Minimum per renewal Composition

Class 1 (1A, 1B, 1C, 1D) 2 classroom hours 1 hour regulatory and industry-standard training + 1 hour equipment-specific training

  • Class 2 (2A–2D) 2 classroom hours Same split
  • Class 3 (3A, 3B) 2 classroom hours Same split
  • Class 4 (4B–4G) 2 hours Same split

Multiple classes: a licensee with more than one class completes only one regulatory hour plus the equipment-specific hour for each class held. A 1B and 2A holder therefore needs 1 regulatory hour + 1 Class 1 equipment hour + 1 Class 2 equipment hour = 3 hours . OPSI's renewal page asks for CE certificates for each restriction renewed , and CE cannot be applied to more than one renewal .

Class 1 curriculum topics (230 CMR 6.04(1)(b)6.a.iii): MGL c. 146; 230 CMR 6.00; 520 CMR 14.00 (Excavation and Trench Safety); OSHA 29 CFR 1926; OSHA 29 CFR 1910; ANSI B30; MGL c. 82 § 40 (Dig Safe); MGL c. 82A (trench safety); and MGL c. 164 § 76D (the underground damage-prevention system). The list doubles as a guide to what the state expects a crane operator to know.

Training facility rules

Facilities apply to the Office with all curricula, training materials, certificates and an instructor list with Massachusetts license numbers. Instructor changes are reported within 14 days .

Every course is monitored by a licensee of equal or greater grade , who signs each certificate and adds their license number.

Certificates show the participant's name, address, email and license grade and number; the provider; the endorsing licensee's printed name, signature and license number; and the date. Authenticity is verified by embossing, electronic transfer, signature verification or numbered certificates.

Attendance records are kept for three years . Falsified records or certificates are grounds for proceedings and can lead to immediate suspension or revocation.

Renewal timing, inactive status and military service

Renewals keep the even-year or odd-year birthday pattern of the original expiration.

A licensee who cannot complete CE may ask in writing for inactive status for up to one CE cycle . An inactive licensee may not operate . To return to active status, the licensee files a request with the renewal fee, a certificate of completion and the 6.02(6) documents.

The Office may accept armed forces education, training or service completed within 24 months , with a Verification of Military Experience and Training form.

A license not renewed is void and, after one year , requires re-examination (inactive licenses excepted). Active-duty licensees keep a valid license until release plus at least 90 days .

Apprentice licenses (230 CMR 6.05)

Issued to a currently unlicensed person, 16 or older , who is registered as an apprentice at a training facility and shows proof of registration.

The apprentice may operate only under the direct guidance of a duly licensed person who is not an apprentice , and must keep the apprentice license on their person while operating.

No exam is required for an apprentice license.

Valid for at most two years , then renewable with the 6.02 documents and proof of current apprentice registration. If not renewed, it becomes void, and after one year a new application is needed.

Facilities that train only apprentices, and offer no CE, file an instructor list with license numbers.

  • Exempt companies and in-service training (230 CMR 6.06–6.07)
  • Who can be exempt

Exemption Key conditions

Public utility companies (truck-mounted cranes, derricks) A licensed supervisory employee is designated the responsible person; an approved in-service program issues company licenses with photo, equipment list and the supervisor's signature

Companies working only on utility property or equipment Meet the utility conditions, hold the utility's company licenses, or restore service at the utility's direction after an emergency, with notice to the Commissioner

Companies using lift trucks, forklifts, overhead cranes and authorized equipment only on their own property A licensed supervisory employee is on site at all times of operation

Forklift-only exemption (consistent with 29 CFR 1910.178) Operators are company employees , and the forklift is used exclusively on company property where the public has no access . Applies only to industrial lift trucks and forklifts

Manufacturer service technicians Employed by the manufacturer or an authorized dealer, have completed the manufacturer's technician certification and can show proof

Public vocational high schools; DAS-recognized operating-engineer training facilities A licensed supervising instructor is on site and designated the responsible person; in-service training for instructors

In-service training minimums (230 CMR 6.07(4))

  • Company license Minimum classroom hours
  • 1A, 1B, 1C 4
  • 1D 2
  • 2A–2D 4
  • 3A 4
  • 4B–4G 2

Programs must include classroom and practical components and be supervised by a licensee of equal or greater grade, who signs every company license. Company licenses show the holder's name, address and photo, the program provider, the endorsing licensee's signature and license number. Records are kept for three years. Program approval is valid for two years , and company licenses must be carried while operating and shown to an Inspector on request. A company license is valid only for hoisting machinery used on company property .