Study guide

3.1 230 CMR 6.01: Scope, Key Definitions, Exempt Equipment & Adopted Standards

Massachusetts Crane Operator Hoisting Engineer License

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Massachusetts Hoisting Law (MGL Chapter 146)

1.1 MGL Chapter 146 §§ 53–54A: The Hoisting License Mandate, Exemptions & Penalties 1.2 MGL Chapter 146 §§ 57–67: Applications, Examinations, Appeals, License Term & Renewal

2 Chapter 2: Licensing Under 230 CMR 6.00

2.1 License Classes & Restrictions Under 230 CMR 6.10 2.2 Applying, Medical Qualification, the OPSI Exam & Renewal (230 CMR 6.02) 2.3 Temporary Permits, Continuing Education, Apprentices & Company Exemptions (230 CMR 6.03–6.07)

3 Chapter 3: 230 CMR 6.00 Definitions, Operating Rules & Enforcement

3.1 230 CMR 6.01: Scope, Key Definitions, Exempt Equipment & Adopted Standards 3.2 Operating Procedures Under 230 CMR 6.08: Inspections, Attention, Signals & Stop Authority 3.3 Special Requirements Under 230 CMR 6.09: Cranes, Derricks, Pile Drivers, Forklifts & Excavators 3.4 Incident Reporting, Investigations, Discipline & Variances (230 CMR 6.11–6.13)

4 Chapter 4: Crane Types, Working Parts & Load Charts

4.1 Crane Types & Working Parts by Restriction: Lattice, Derrick, Tower, Telescopic & Hydraulic Machines 4.2 Load Chart Fundamentals: Structural Strength vs. Stability Limits 4.3 Capacity Deductions & Calculating Net Allowable Capacity 4.4 Quadrants of Operation, Working Radius & Boom Angle Dynamics

5 Chapter 5: Advanced Lift Calculations & Multi-Crane Operations

5.1 Boom Deflection, Ground Leveling & Side-Loading Hazards 5.2 Wire Rope Reeving, Parts of Line & Single-Line Pull Limits 5.3 Center of Gravity, Weight Distribution & Multi-Crane (Tandem) Lifts

6 Chapter 6: Dig Safe, Underground Utilities & Trench Safety

6.1 Massachusetts Dig Safe Law (MGL c. 82 §§ 40–40E, 220 CMR 99.00): Premarking & Notice 6.2 Utility Color Codes, the 18-Inch Safety Zone, Excavating Near Facilities & Damage Response 6.3 Trench Safety Law, Excavation Hazards, Setbacks & Utility-Strike Emergencies

7 Chapter 7: Power Lines, Ground Conditions & Weather

7.1 Power Line Safety: OSHA 1926.1408–1411, Table A & Table T 7.2 Ground Bearing Pressure, Outrigger Setup & Cribbing Sizing 7.3 Wind, Storms, Lightning, Ice & Cold: Weather Limits for Crane Work

8 Chapter 8: Rigging Principles, Slings & Hardware

8.1 Sling Types: Synthetic, Wire Rope, and Alloy Steel Chain Slings 8.2 Sling Angle Calculations & Tension Formulas 8.3 Rigging Hardware, Shackles, Hooks & Below-the-Hook Lifting Devices

9 Chapter 9: Wire Rope & Crane Inspection

9.1 Wire Rope Construction, Damage Assessment & Removal Criteria (OSHA 1926.1413) 9.2 Crane Inspections, Safety Devices & Operational Aids (230 CMR 6.08; OSHA 1926.1412, 1415, 1416)

10 Chapter 10: Hand Signals & Personnel Hoisting

10.1 Standard Hand Signals, Voice & Radio Signals and Signal Person Qualification 10.2 Crane-Suspended Personnel Platforms (230 CMR 6.09(6) & OSHA 29 CFR 1926.1431)

3.1 230 CMR 6.01: Scope, Key Definitions, Exempt Equipment & Adopted Standards

Key Takeaways Explain This Topic AI

230 CMR 6.00 was recodified from 520 CMR 6 and published by the Division of Occupational Licensure on November 21, 2025 (Mass. Register #1561).

Jib and other shop cranes count as hoisting machinery when capable of lifting more than two tons or more than 12 feet (230 CMR 6.01(2)).

Service truck cranes used for vehicle repair with capacity under 14,000 pounds, tow trucks and bucket truck hoists of two tons or less are exempt equipment (230 CMR 6.01).

For incident reporting, property damage means damage to private or public property exceeding $10,000 per incident (230 CMR 6.01).

230 CMR 6.01(3) adopts ASME B30.5-2018 for mobile cranes, B30.9-2018 for slings, B30.26-2015 for rigging hardware, SAE J1307-2002 for excavator signals, and OSHA 29 CFR 1926 and 1910.

Last updated: October 2026

From 520 CMR 6 to 230 CMR 6.00

The hoisting regulation used to be 520 CMR 6.00 , written when hoisting licensing sat under the Department of Public Safety. Licensing moved to the Division of Occupational Licensure , and the regulation was recodified as 230 CMR 6.00, Hoisting Machinery . The current text is dated 11/21/2025 (Massachusetts Register #1561), and mass.gov notes it was "previously codified as 520 CMR 6." Older study materials, CE handouts and practice tests that cite "520 CMR 6.00" refer to the same subject, but section details changed . Study the 230 CMR text.

One consequence of the recodification is spelled out in 230 CMR 6.01(4): the Office may issue written advisory rulings, but advisories dated before November 21, 2025 are null and void.

Scope (230 CMR 6.01(1))

230 CMR 6.00 protects public safety by setting the minimum standards to obtain a hoisting license or temporary permit and the minimum safety standards to be followed while operating . It applies to hoisting machinery used on private or public property for building, altering, demolishing, repairing or maintaining buildings, structures, bridges, highways, dams, tunnels, sewers, pipelines and all other construction projects or facilities , and for other uses on private or public grounds, including warehousing and movement of materials . The one exception is machinery used exclusively for agricultural purposes .

What counts as "hoisting machinery"

The definition starts with the statute's wording (derricks, cableways, cargo-discharging machinery and temporary elevator cars, with mechanical motive power other than steam) and then lists what it includes, but is not limited to :

  • tower cranes, lattice boom cranes, and telescoping boom cranes with or without wire rope ;
  • telehandlers, forklifts and other general industrial fork trucks;
  • crawler and rubber-tired excavators, backhoes and front-end loaders;
  • compact hoisting machinery;
  • overhead gantry cranes and marine lifts;
  • jib and other shop cranes capable of lifting more than two tons or more than 12 feet ;
  • specialty equipment categorized in 230 CMR 6.10; and

any other machinery the Commissioner deems governed by MGL c. 146 § 53.

Each item includes the machine with or without manufacturer-approved attachments .

Note

The two-ton and 12-foot test is written for jib and other shop cranes , and it is an "or" test. A jib crane rated at 1½ tons with a 14-foot lift is covered. So is a 3-ton jib crane with an 8-foot lift. Overhead gantry cranes are listed without any threshold.

Equipment exempt from 230 CMR 6.00

The regulation lists equipment that "has not historically been deemed to be hoisting machinery":

  • Exempt equipment Limit stated in 230 CMR 6.01
  • Municipal solid waste vehicles —
  • Vacuum trucks —
  • Street sweeping equipment —
  • Service truck cranes used for vehicle repair Capacity less than 14,000 pounds
  • Tow trucks Used for towing any size motor vehicle
  • Bucket-truck-mounted hoists Capacity of two tons or less
  • Truck-mounted lift gates —
  • Pallet movers Lifting height less than two feet
  • Portable electric chain hoists Capacity of 2½ tons or less using a power source of 240 volts or less
  • Other equipment Specifically excluded by the Commissioner
  • Definitions that show up on exam questions
  • Term 230 CMR 6.01 meaning
  • Office The Office of Public Safety and Inspections within the Division of Occupational Licensure
  • Chief The Chief of Inspections of the Office, or designee
  • Inspector A District Engineering Inspector employed by the Office

Licensee A person 18 or older who has met the requirements for licensure (includes anyone holding a license, permit or other authority under 230 CMR 6.00)

Apprentice licensee A person 16 or older with an apprentice license, operating under direct guidance and supervision of a licensed non-apprentice

Compact hoisting machinery Gross vehicle weight not exceeding 10,000 pounds , excluding Class 1, 3 and 4 machinery

Competent person Capable of identifying existing and predictable hazards and authorized to take prompt corrective measures

Emergency procedure Actions required when imminent danger may occur, to prevent damage to life or property or to ensure public safety

Incident A situation resulting in serious injury, property damage, or any condition requiring action to preserve public health or safety

Serious injury Death, dismemberment, significant disfigurement, permanent loss of use of a body organ, member, function or system, a compound fracture or other significant injury or illness; a doctor's order for inpatient admission also counts

Property damage Damage to private or public property exceeding $10,000 per incident

Mechanical failure Damage to or breakdown of hoisting machinery affecting capacity or safe operation per the manufacturer's specifications

Modification Alterations, extensions or repairs that change the machine's original structure

Manufacturer approved attachment An attachment designed or approved per the manufacturer's specifications; if the manufacturer no longer exists, a Massachusetts registered professional engineer must approve it in writing

Operator's manual The manufacturer's document with the required procedures and forms for safe operation of that equipment

Safety factor The ratio of the maximum stress a part can withstand to the maximum stress estimated for its intended use

Signal person A trained person qualified in hand signals, audible signals or flashing lights who directs the operator and warns of hazards (Appendices A and B)

  • Qualified welder Certified by the American Welding Society or an acceptable alternative
  • Regulations and standards adopted (230 CMR 6.01(3))

The operating standard for hoisting machinery is set by these documents:

Standard Subject

ASME B30.2-2016 Overhead and gantry cranes (top running bridge, single or multiple girder, top running trolley hoist)

  • ASME B30.3-2016 Tower cranes
  • ASME B30.5-2018 Mobile and locomotive cranes
  • ASME B30.9-2018 Slings
  • ASME B30.10-2014 Hooks
  • ASME B30.11-2010 Monorails and underhung cranes
  • ASME B30.16-2017 Overhead hoists (underhung)
  • ASME B30.17-2015 Overhead and gantry cranes (top running bridge, single girder, underhung hoist)
  • ASME B30.20-2018 Below-the-hook lifting devices
  • ASME B30.22-2016 Articulating boom cranes
  • ASME B30.26-2015 Rigging hardware
  • SAE J1307-2002 Excavator and backhoe hand signals
  • 29 CFR 1926 / 29 CFR 1910 OSHA construction and general industry standards
  • 220 CMR 99.00 Dig Safe enforcement procedures under MGL c. 82 §§ 40–40E

The operating rules in 230 CMR 6.08(1) add that when 230 CMR 6.08 and OSHA conflict, the provision setting the higher standard for safety prevails (Section 3.2).

Applying the definitions

Shop jib crane, 1-ton rating, 16-foot hook travel. It can lift more than 12 feet, so it is hoisting machinery. A rated jib crane with no load chart falls under 3A.

Mechanic's service truck crane, 8,000-lb capacity, used for vehicle repair. Exempt, because capacity is under 14,000 pounds and it is used for vehicle repair. Used to set rooftop units, it is no longer being used for vehicle repair.

Wrecker towing a disabled box truck. Exempt: tow trucks used for towing any size motor vehicle.

2-ton chain hoist on 120-volt power. Exempt: a portable electric chain hoist of 2½ tons or less on 240 volts or less.

Crane strikes a parked car, $6,500 damage, no injury. Below the $10,000 property-damage definition. Check whether any other reportable condition exists (Section 3.4).