Study guide
15.3 Slope, Fall & Grade
Massachusetts Journeyman Plumber Study Guide Exam
Track your progress as you read
Finished sections get a check mark.
1 Massachusetts Licensing, Permits & Exam Process
1.1 Board, M.G.L. c. 142 & License Hierarchy 1.2 Permits, Inspections & Product Acceptance 1.3 Education, Experience, PSI Process & Excavation Safety
2 Fuel Gas Code, Materials & Pipe Sizing
2.1 248 CMR 4.00/5.00, Materials & Components 2.2 Gas Pipe Sizing & Demand 2.3 Underground Gas Installation
3 CSST, Regulators, Testing & Purging
3.1 CSST Installation 3.2 Gas Piping Regulators 3.3 Inspection, Testing & Purging
4 Combustion Air, Appliances & Large Equipment
4.1 Combustion Air 4.2 Specific Equipment, Testing & Adjustment 4.3 Gas Equipment over 400,000 BTU
5 Appliance Venting Categories, Draft & Chimneys
5.1 Positive vs Non-Positive Venting 5.2 Natural Draft Venting 5.3 Chimneys
6 Gas Vent Sizing & Part II Gas Practical
6.1 Gas Vent Sizing & Materials 6.2 Part II Practical Gas Piping 6.3 Part II Practical Gas Venting
7 Traps, Cleanouts & Joints
7.1 Trap Design, Seals & Prohibited Traps 7.2 Cleanout Locations, Sizing & Clearances 7.3 Joints, Connections & Prohibited Practices
8 Fixtures, Valves & Water Heaters
8.1 Fixtures, Equipment & Clearances 8.2 Piping, Valves & Controls 8.3 Water Heaters, T&P & M.G.L. c. 142
9 Water Supply, Backflow & Temperatures
9.1 Water Supply Materials, WSFU & Sizing 9.2 Backflow Prevention & Cross-Connection 9.3 Water Temperatures, Scald Control & Thermal Expansion
10 Hangers, DWV Materials & Storm Drainage
10.1 Hangers, Anchors & Pipe Protection 10.2 DWV Piping Materials 10.3 Storm Drainage
11 Sanitary Drainage Sizing
11.1 DFU Values & Load Calculations 11.2 Building Drains & Building Sewers 11.3 Horizontal Branches, Stacks & Offsets
12 Indirect Waste, Special Waste & Plumbing Vent Principles
12.1 Indirect Waste 12.2 Special Waste 12.3 Plumbing Vent Sizing Principles
13 Plumbing Vent Types & Terminations
13.1 Individual, Common & Dual Vents 13.2 Wet, Circuit, Loop & Stack Venting 13.3 Vent Terminations & Special Venting
14 Interceptors, Separators & Holding Tanks
14.1 Grease Interceptors 14.2 Holding Tanks 14.3 Gasoline, Oil & Sand Separators
15 Part II Trade Calculations
15.1 Head, Pressure & Volume 15.2 Pipe Offsets 15.3 Slope, Fall & Grade
16 Part II Isometric Analysis
16.1 Isometric Symbols & Reading Order 16.2 DWV Isometric Takeoff 16.3 Fixture, Vent & Gas Isometric Plan Analysis
15.3 Slope, Fall & Grade
Key Takeaways Explain This Topic AI
Fall equals slope times run: at 1/4 inch per foot, a 40-foot run falls 10 inches; at 1/8 inch per foot, the same run falls 5 inches.
1/8 inch per foot is 0.125 ÷ 12 = 1.04 percent grade; 1/4 inch per foot is 2.08 percent; 1/2 inch per foot is 4.17 percent.
248 CMR 10.15 Table 2 (12/8/2023) prints no 1/8 in/ft column on a 3-inch building drain (40 DFU at 1/4 in/ft, 48 DFU at 1/2 in/ft); 248 CMR 10.05 requires at least 1/4 in/ft on horizontal drainage 3 inches and smaller.
Grade between two inverts is the invert difference divided by the run, then converted to inches per foot or percent; 248 CMR 10.03 defines invert as the lowest inside point of the pipe.
Horizontal drainage larger than 3 inches may use 1/8 in/ft; Table 2 loads a 4-inch building drain at 180 DFU at 1/8 in/ft, 216 DFU at 1/4, and 250 DFU at 1/2.
Last updated: September 2026
15.3 Slope, Fall & Grade
Quick Answer: Fall = slope × run. 1/4 in/ft × 40 ft = 10 inches of fall; 1/8 in/ft × 40 ft = 5 inches . 1/8 in/ft = 0.125 ÷ 12 = 1.04 percent grade. 248 CMR 10.15 Table 2 has no 1/8 in/ft column for a 3-inch building drain ( 40 DFU at 1/4 , 48 at 1/2 ). 248 CMR 10.05 sets 1/4 in/ft minimum on horizontals 3 inches and smaller , and 1/8 in/ft minimum on pipe larger than 3 inches . Grade between two inverts is (invert difference) ÷ run . Invert is the lowest inside point of the pipe ( 248 CMR 10.03 ).
Part II will mix a tape-measure fall problem with a Massachusetts pitch rule. Independent ExamFinch teaching below is the math plus the 12/8/2023 table cell that forbids a 3-inch building drain at 1/8. Chapter 11.2 owns the full DFU columns; this section computes how far the invert drops and whether that pitch is a Table 2 option .
248 CMR 10.03 defines invert as the lowest point inside a pipe on which water can flow. Slope in that chapter points to grade . Grade is invert to invert, not dirt trench to dirt trench and not crown to crown. 248 CMR 10.05(2)(a) requires horizontal drainage to run in a straight practical line at a consistent uniform pitch . Do not steepen the last 10 feet to “make the invert” after laying 70 feet flat.
Formula table — fall, percent, inverts
- Pitch people say Inches per foot Feet per foot Percent grade
- 1/8 in/ft 0.125 0.01042 1.04%
- 1/4 in/ft 0.250 0.02083 2.08%
- 1/2 in/ft 0.500 0.04167 4.17%
Fall (inches) = (inches per foot) × run (feet).
Percent grade = (inches per foot ÷ 12) × 100 , which is the same as (fall in feet ÷ run in feet) × 100 .
1/8 in/ft to percent, written out: 1/8 = 0.125 inch of fall in 12 inches of run. 0.125 ÷ 12 = 0.0104167 . × 100 = 1.04167 percent → 1.04% . As a fraction: (1/8) / 12 = 1/96 ≈ 1.04% . 1/4 in/ft: 0.25 ÷ 12 = 0.020833 → 2.08% . 1/2 in/ft: 0.50 ÷ 12 = 0.041667 → 4.17% .
Between two inverts:
Fall in feet = upstream invert − downstream invert (when both are in feet).
Fall in inches = fall in feet × 12 .
Inches per foot = fall in inches ÷ run in feet .
Percent = (fall in feet ÷ run in feet) × 100 .
If the downstream invert is higher , gravity flow on that run is gone. That is a 10.15(9) ejector problem, not a “negative 1/8” grade.
Massachusetts pitch, including the blank 3-inch 1/8 cell
248 CMR 10.05(2)(b): horizontal drainage 3 inches or smaller — minimum uniform pitch 1/4 inch per foot .
248 CMR 10.05(2)(c): horizontal drainage larger than 3 inches — minimum uniform pitch 1/8 inch per foot .
248 CMR 10.05(2)(d): a Massachusetts professional engineer may design a different pitch if computed velocity is not less than 2 feet per second . That is not a journeyman 1/8-on-3-inch shortcut.
248 CMR 10.05(2)(e) sends building-drain pitch to 10.15 Table 2 . Table 2 (effective 12/8/2023 ) for building drains:
- Diameter (in.) 1/8 in/ft (DFU) 1/4 in/ft (DFU) 1/2 in/ft (DFU)
- 3 — (no column) 40 48
- 4 180 216 250
A 3-inch building drain cannot use 1/8 in/ft because the table has no cell and 10.05 already forbade that pitch on 3-inch and smaller pipe. You can still compute the fall of a 1/8 pitch — 40 ft × 0.125 = 5 inches — and then mark it illegal for that 3-inch building drain. The legal minimum pitch on that 3-inch horizontal is 1/4 in/ft , so the same 40 feet must fall 10 inches , and Table 2 will only load 40 DFU at 1/4 (or 48 at 1/2 ). Independently, the 10-foot foundation section of a building drain is still minimum 4 inch under 248 CMR 10.03 . Do not punch a 3-inch building drain through the wall because 40 DFU “fits” the 1/4 column.
4-inch and larger may use 1/8 in/ft . That is when 180 DFU versus 216 DFU on a 4-inch building drain matters: 216 is the 1/4 column , not the 1/8 column. Chapter 11.2 drills that trap; here you only need it so a fall calculation at 1/8 on 4-inch pipe is a legal pitch if Table 2 load also fits 180 DFU .
Worked example 1 — Fall from a stated pitch (Quincy sewer run)
A 4-inch building sewer runs 36 feet at 1/4 in/ft .
Fall = 0.25 in/ft × 36 ft = 9.00 inches.
At 1/8 in/ft the same 36 feet would fall 0.125 × 36 = 4.50 inches . Four-inch pipe is larger than 3 inches, so 1/8 is a legal minimum pitch under 10.05; you still check Table 2 load ( 180 DFU at 1/8). If the stem switches the pipe to 3-inch , 4.50 inches is the fall of an illegal 1/8 pitch. The 3-inch run needs 9.00 inches at 1/4.
1/2 in/ft on 36 feet: 0.50 × 36 = 18 inches . That is a steep building drain; Table 2 allows more DFU at 1/2 ( 250 on 4-inch, 48 on 3-inch) because the water moves faster. Uniform pitch still means the whole 36 feet, not 18 inches of drop in the last 6 feet.
Worked example 2 — Convert 1/8 in/ft to percent, then use it
1/8 in/ft → percent: 0.125 ÷ 12 × 100 = 1.0417% → 1.04% .
A surveyor calls 1.04% on 80 feet of 4-inch sewer. Fall in feet = 0.010417 × 80 = 0.833 feet . Inches = 0.833 × 12 = 10.00 inches . Check the shop way: 1/8 in/ft × 80 ft = 10 inches . Percent and inches-per-foot agreed.
Wrong conversions: 0.125% (forgot to divide by 12 and multiply by 100 correctly), 12.5% (used 0.125 × 100 and skipped the 12 inches in a foot), 8% (wrote 1/8 as 8 percent). Those show up as distractors because they look like the 1/8.
2.08% is 1/4 in/ft , not 1/8. If an invert pair produces 2.08% , you are at 1/4 , which is what a 3-inch horizontal needed anyway.
Worked example 3 — Grade between two inverts (Fall River)
Upstream invert 64.80 ft . Downstream invert 64.20 ft . Run 48.00 ft (horizontal distance along the pipe as given).
Fall = 64.80 − 64.20 = 0.60 ft = 0.60 × 12 = 7.2 inches.
Inches per foot = 7.2 ÷ 48 = 0.15 in/ft.
Percent = (0.60 ÷ 48) × 100 = 1.25%.
0.15 in/ft sits between 1/8 ( 0.125 ) and 1/4 ( 0.250 ). On a 4-inch building drain, 0.15 is steeper than the 1/8 minimum , so pitch is not the 10.05 problem; Table 2 load still uses the 1/8 column (180 DFU) only if you are actually at 1/8 — here the as-built grade is 0.15 in/ft , closer to 1/8 than to 1/4, and you do not get to claim the 216 DFU 1/4 column unless the invert drop is a true 1/4 . This item asked for the computed grade , not a DFU upgrade.
If the same 0.60-foot drop is stretched over 80 feet : 7.2 ÷ 80 = 0.090 in/ft , which is flatter than 1/8 ( 0.125 ). Percent = 0.60/80 × 100 = 0.75% . That fails 10.05(2)(c) on pipe larger than 3 inches unless a PE designs ≥ 2 fps. Raising the upstream invert or lowering the downstream invert (or shortening the run) is how gravity comes back; wishing 1/8 onto the as-built numbers does not.
3-inch, 40-foot, 1/8 proposal: fall would be 40 × 0.125 = 5 inches . Table 2 still has no 1/8 cell for 3-inch building drain. Pitch it at 1/4 : 40 × 0.25 = 10 inches of invert drop, load cap 40 DFU , and remember the through-wall building drain is still 4 inch under 10.03 for the foundation piece.
Official resources
248 CMR 10.05(2) (Cornell) — 1/4 in/ft on 3-inch and smaller; 1/8 in/ft on larger; PE 2 fps exception; pointer to Table 2
- 248 CMR 10.15 Table 2 (Cornell) — blank 3-inch 1/8 in/ft building-drain cell; 40 / 48; 4-inch 180 / 216 / 250
- 248 CMR 10.03 Definitions (Cornell) — invert; slope see grade; building drain 10-foot / 4-inch piece
- 248 CMR 10.00 Uniform State Plumbing Code (Mass.gov, effective 12/8/2023) — official PDF tables
- PSI Massachusetts plumbing Candidate Information Bulletin — Part II General Trade Calculations 5