Study guide
1.5 Domain Weights and Master-Level Study Map
Master Electrician Study Guide Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Master Exam Orientation and Source Control
1.1 ICC R16, T16, G16, and Jurisdiction Variance 1.2 Current Format, Cost, Time, and Passing Score 1.3 Master License Scope vs. Exam Provider 1.4 Official References, Open-Book Rules, and Calculators 1.5 Domain Weights and Master-Level Study Map 1.6 Using the Practice Bank, Error Log, and Code Index
2 Chapter 2: Master-Level Electrical Theory, Plans, and Calculations
2.1 Plan Reading, Specifications, and Supervisory Review 2.2 Ohms Law, Power Factor, and Three-Phase Review 2.3 Fault Current, Available Fault Current, and Equipment Ratings 2.4 Demand Loads, Continuous Loads, and Calculation Setup 2.5 Voltage Drop and Design Judgment 2.6 Coordination, Selectivity, and Master-Level Decision-Making 2.7 Theory, Plans, and Calculation Case Lab
3 Chapter 3: Services, Service Equipment, and Main Distribution
3.1 Service Point, Service Conductors, and Utility Boundaries 3.2 Service Load Calculations and Demand-Factor Workflow 3.3 Service Disconnects, Overcurrent Protection, and Grouping 3.4 Service Equipment Ratings, Clearances, and Working Space 3.5 Transformers and Separately Derived System Decisions 3.6 Temporary Services and Construction Power 3.7 Services and Main Distribution Case Lab
4 Chapter 4: Grounding, Bonding, and Fault-Current Paths
4.1 Grounding vs. Bonding and Exam Language 4.2 Grounding Electrode Systems and Grounding Electrode Conductors 4.3 Main Bonding Jumpers, System Bonding, and Equipment Bonding 4.4 Separately Derived Systems Grounding and Bonding 4.5 Fault-Current Paths, Clearing Time, and Equipment Ratings 4.6 Special Bonding Patterns: Pools, Services, and Metal Systems 4.7 Grounding and Bonding Case Lab
5 Chapter 5: Feeders, Branch Circuits, and Conductor Engineering
5.1 Feeder vs. Branch Boundaries and Load Flow 5.2 Conductor Ampacity, Temperature Ratings, and Terminal Limits 5.3 Adjustment, Correction, and Neutral Counting 5.4 Overcurrent Protection, Tap Conductors, and Next-Size Rules 5.5 Required Outlets, GFCI/AFCI, and Occupancy Patterns 5.6 Multiwire Branch Circuits, Shared Neutrals, and Voltage Drop 5.7 Feeders, Branch Circuits, and Conductor Case Lab
6 Chapter 6: Wiring Methods, Raceways, Box Fill, and Installation Judgment
6.1 Raceway Selection and Installation Conditions 6.2 Raceway Fill, Conductor Protection, and Bending Limits 6.3 Boxes, Enclosures, and Conduit Bodies 6.4 Box Fill: Device Yokes, Equipment Grounds, and Clamps 6.5 Underground, Wet, Corrosive, and Physical-Damage Locations 6.6 Cabinets, Panelboards, Switchboards, and Working Clearance 6.7 Wiring Methods Installation Case Lab
7 Chapter 7: Equipment, Devices, Controls, and Utilization Equipment
7.1 Luminaires, Receptacles, Switches, and Device Placement 7.2 Appliances, Utilization Equipment, and Nameplate Data 7.3 Heating, Cooling, and HVAC Equipment Branch-Circuit Decisions 7.4 Disconnects, Switches, Controllers, and Control-Circuit Logic 7.5 Panelboards, Switchboards, Cabinets, and Equipment Labeling 7.6 Working Space, Accessibility, and Maintenance Judgment 7.7 Equipment, Devices, and Controls Case Lab
8 Chapter 8: Motors, Generators, Transformers, and Power Systems
8.1 Motor Loads, Full-Load Current, and Nameplate Boundaries 8.2 Motor Conductors, Overloads, and Short-Circuit/Ground-Fault Protection 8.3 Motor Controllers, Disconnects, and Group Installations 8.4 Generators, Transfer Equipment, and Optional Standby Systems 8.5 Emergency, Legally Required, and Critical Power Distinctions 8.6 Transformer Primary, Secondary, and Grounding Decisions 8.7 Motors, Generators, and Power Systems Case Lab
9 Chapter 9: Special Occupancies, Emergency Systems, and Safety
9.1 Hazardous Classified Locations and Boundary Thinking 9.2 Healthcare, Places of Assembly, and Commercial Special Rules 9.3 Pools, Spas, Marinas, and Corrosive/Wet Environments 9.4 RV Parks, Mobile Homes, Data Centers, and Special Equipment 9.5 Emergency Systems, Signaling, and Fire Alarm Interfaces 9.6 OSHA Electrical Safety, Lockout, and Field Risk Control 9.7 Special Occupancies and Safety Case Lab
10 Chapter 10: Master Electrician Integrated Code and Calculation Labs
10.1 Residential Service Upgrade Integrated Lab 10.2 Small Commercial Tenant Improvement Integrated Lab 10.3 Motor Shop and Industrial Equipment Integrated Lab 10.4 Mixed-Occupancy Special Condition Integrated Lab 10.5 Generator, Transfer, and Emergency Load Integrated Lab 10.6 Plan Review, Redline, and Supervisory Correction Lab 10.7 Five-Hour Open-Book Simulation Strategy
11 Chapter 11: Final Review, Test Day, Licensing, and Business Next Steps
11.1 Final 30-Day Master Electrician Review Plan 11.2 Reference Tab, Index, and Open-Book Speed Drills 11.3 Test-Day Checklist: Pearson VUE, PRONTO, and Retake Rules 11.4 After the Score: Jurisdiction Application and License Next Steps 11.5 Business, Supervision, Permit, and Compliance Readiness 11.6 Master Electrician Final Mixed Review
1.5 Domain Weights and Master-Level Study Map
Key Takeaways Explain This Topic AI
R16 and T16 share the same domain weights, with wiring methods and materials at 19%, services at 16%, branch circuits and conductors at 16%, and special occupancies at 12%.
Domain weights should guide study time, but weak low-weight domains can still decide the result on a 75% exam.
A master-level map connects Articles 90, 100, 110, 210, 215, 220, 230, 240, 250, 300, 310, 314, 430, 445, 517, 680, 690, 700, 701, and 702 to common exam tasks.
Study by task type as well as domain: classify, calculate, select table, apply exception, check condition of use, and eliminate distractors.
The local practice bank is weighted differently from the ICC outline, so candidates should supplement categories that are underrepresented.
Last updated: May 2026
Turning the outline into a study map
R16 and T16 share the same master electrician domain weights in the source brief. General Knowledge is 12%. Services and Service Equipment is 16%. Feeders is 4%. Branch Circuits and Conductors is 16%. Wiring Methods and Materials is 19%. Equipment and Devices is 10%. Control Devices is 3%. Motors and Generators is 8%. Special Occupancies, Equipment, and Conditions is 12%. On a 100-question exam, those percentages also give a rough question count.
The largest domains deserve repeated attention. Wiring methods and materials at 19% can cover raceways, cables, boxes, conductor fill, support, protection from damage, wet and damp locations, underground rules, and installation details scattered across Chapter 3. Services and service equipment at 16% can include service conductors, disconnecting means, service equipment ratings, grounding electrode conductors, bonding, working space, and available fault current concepts.
Branch circuits and conductors at 16% can reach load classification, ampacity, overcurrent protection, receptacle and outlet rules, dwelling and nondwelling distinctions, and conductor identification.
The smaller domains cannot be ignored. Feeders at 4% may seem minor, but feeder questions often combine load calculation, conductor ampacity, grounding conductor sizing, neutral load, overcurrent protection, and voltage system facts. Control devices at 3% may be only a few questions, yet a candidate near the pass line cannot donate those points. A 75% passing target means every domain matters. The outline tells you probability, not permission to skip.
A master-level study map should connect domains to article routes. Start with Article 90 for code purpose and arrangement, Article 100 for definitions, and Article 110 for general installation requirements, equipment ratings, listing and labeling, working space, short-circuit current marking, and termination basics. Then map branch circuits through Articles 210, 220, 240, 250, 300, and 310. Map feeders through Articles 215, 220, 225 when outside feeders appear, 240, 250, and 310. Map services through Articles 230, 250, 240, 310, and 110.
Wiring methods need a chapter map, not just one article. Article 300 provides general wiring method rules. Article 310 supports conductor ampacity. Article 314 supports boxes and fittings. Raceways such as EMT, PVC, rigid metal conduit, intermediate metal conduit, and flexible raceways live in their own articles. Cable methods such as NM, MC, AC, SE, and underground feeder cable also have separate articles. The exam can ask whether a method is permitted, how it must be supported, where it is prohibited, or how fill and conductor count affect the installation.
Motors and generators require a different mental model because ordinary conductor and overcurrent rules are modified. Article 430 separates motor branch-circuit conductors, short-circuit and ground-fault protection, overload protection, controllers, disconnects, and feeders. A common trap is using one protective device rule for every motor purpose. Article 445 and related generator provisions require attention to source characteristics, disconnecting means, grounding, bonding, transfer equipment, and optional versus legally required standby systems when Articles 700, 701, and 702 enter the facts.
Special occupancies, equipment, and conditions are high-value because they often override ordinary instincts. Health care facilities, swimming pools, hazardous classified locations, signs, photovoltaics, emergency systems, and optional standby systems each have article-specific rules. The study map should mark these as overlay domains. First solve the ordinary installation category, then ask whether the special article modifies it. For example, a receptacle near a pool is not just a receptacle question. It is a branch-circuit and special occupancy question.
Use task types to organize practice. Classification questions ask what the installation is. Navigation questions ask where the rule lives. Calculation questions ask for load, ampacity, fill, conductor size, or protection. Condition-of-use questions ask whether wet location, temperature, number of conductors, continuous load, or occupancy changes the result. Exception questions ask whether an exception applies or is being misused. Distractor questions ask whether you can reject plausible but wrong article routes.
The local practice bank described in the source brief has 200 items, but its category counts do not exactly match the ICC outline. It is heavy in feeders and branch circuits, motors and generators, wiring methods, special occupancies, and equipment devices. It has fewer services items and fewer general items than the outline would suggest for a 100-question exam. That does not make the bank bad; it means you should use it with a gap plan. Add focused service, general knowledge, and source-control drills if your practice history shows underexposure.
A practical weekly map might allocate time as follows: two sessions for wiring methods, two for services and grounding, two for branch circuits and conductor calculations, one for motors and generators, one for special occupancies, one for equipment and devices, and short daily drills for definitions, Article 110, and control devices. Every week should include at least one mixed set because the real exam does not announce article numbers. Mastery is the ability to move from fact pattern to controlling source under time pressure.
Do not read the NEC straight through as your only method. Reading builds familiarity, but exams award selected decisions. For each domain, create five routes: the article route, the table route, the calculation route, the exception route, and the common trap route. Then practice until you can explain why the wrong options are wrong. That is the difference between a candidate who has seen the book and a candidate who can use it.
Structured Decision Aid
Prioritize wiring methods, services, branch circuits, general knowledge, and special conditions before low-weight topics.
Pair every calculation domain with a lookup drill so the open-book format does not become a time sink.
Track weak domains by missed-question cause: wrong article, wrong table, wrong formula, or wrong field assumption.
Reserve final-week review time for mixed labs because master-level questions often cross domain boundaries.