Study guide
1.1 ICC R16, T16, G16, and Jurisdiction Variance
Master Electrician Study Guide Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Master Exam Orientation and Source Control
1.1 ICC R16, T16, G16, and Jurisdiction Variance 1.2 Current Format, Cost, Time, and Passing Score 1.3 Master License Scope vs. Exam Provider 1.4 Official References, Open-Book Rules, and Calculators 1.5 Domain Weights and Master-Level Study Map 1.6 Using the Practice Bank, Error Log, and Code Index
2 Chapter 2: Master-Level Electrical Theory, Plans, and Calculations
2.1 Plan Reading, Specifications, and Supervisory Review 2.2 Ohms Law, Power Factor, and Three-Phase Review 2.3 Fault Current, Available Fault Current, and Equipment Ratings 2.4 Demand Loads, Continuous Loads, and Calculation Setup 2.5 Voltage Drop and Design Judgment 2.6 Coordination, Selectivity, and Master-Level Decision-Making 2.7 Theory, Plans, and Calculation Case Lab
3 Chapter 3: Services, Service Equipment, and Main Distribution
3.1 Service Point, Service Conductors, and Utility Boundaries 3.2 Service Load Calculations and Demand-Factor Workflow 3.3 Service Disconnects, Overcurrent Protection, and Grouping 3.4 Service Equipment Ratings, Clearances, and Working Space 3.5 Transformers and Separately Derived System Decisions 3.6 Temporary Services and Construction Power 3.7 Services and Main Distribution Case Lab
4 Chapter 4: Grounding, Bonding, and Fault-Current Paths
4.1 Grounding vs. Bonding and Exam Language 4.2 Grounding Electrode Systems and Grounding Electrode Conductors 4.3 Main Bonding Jumpers, System Bonding, and Equipment Bonding 4.4 Separately Derived Systems Grounding and Bonding 4.5 Fault-Current Paths, Clearing Time, and Equipment Ratings 4.6 Special Bonding Patterns: Pools, Services, and Metal Systems 4.7 Grounding and Bonding Case Lab
5 Chapter 5: Feeders, Branch Circuits, and Conductor Engineering
5.1 Feeder vs. Branch Boundaries and Load Flow 5.2 Conductor Ampacity, Temperature Ratings, and Terminal Limits 5.3 Adjustment, Correction, and Neutral Counting 5.4 Overcurrent Protection, Tap Conductors, and Next-Size Rules 5.5 Required Outlets, GFCI/AFCI, and Occupancy Patterns 5.6 Multiwire Branch Circuits, Shared Neutrals, and Voltage Drop 5.7 Feeders, Branch Circuits, and Conductor Case Lab
6 Chapter 6: Wiring Methods, Raceways, Box Fill, and Installation Judgment
6.1 Raceway Selection and Installation Conditions 6.2 Raceway Fill, Conductor Protection, and Bending Limits 6.3 Boxes, Enclosures, and Conduit Bodies 6.4 Box Fill: Device Yokes, Equipment Grounds, and Clamps 6.5 Underground, Wet, Corrosive, and Physical-Damage Locations 6.6 Cabinets, Panelboards, Switchboards, and Working Clearance 6.7 Wiring Methods Installation Case Lab
7 Chapter 7: Equipment, Devices, Controls, and Utilization Equipment
7.1 Luminaires, Receptacles, Switches, and Device Placement 7.2 Appliances, Utilization Equipment, and Nameplate Data 7.3 Heating, Cooling, and HVAC Equipment Branch-Circuit Decisions 7.4 Disconnects, Switches, Controllers, and Control-Circuit Logic 7.5 Panelboards, Switchboards, Cabinets, and Equipment Labeling 7.6 Working Space, Accessibility, and Maintenance Judgment 7.7 Equipment, Devices, and Controls Case Lab
8 Chapter 8: Motors, Generators, Transformers, and Power Systems
8.1 Motor Loads, Full-Load Current, and Nameplate Boundaries 8.2 Motor Conductors, Overloads, and Short-Circuit/Ground-Fault Protection 8.3 Motor Controllers, Disconnects, and Group Installations 8.4 Generators, Transfer Equipment, and Optional Standby Systems 8.5 Emergency, Legally Required, and Critical Power Distinctions 8.6 Transformer Primary, Secondary, and Grounding Decisions 8.7 Motors, Generators, and Power Systems Case Lab
9 Chapter 9: Special Occupancies, Emergency Systems, and Safety
9.1 Hazardous Classified Locations and Boundary Thinking 9.2 Healthcare, Places of Assembly, and Commercial Special Rules 9.3 Pools, Spas, Marinas, and Corrosive/Wet Environments 9.4 RV Parks, Mobile Homes, Data Centers, and Special Equipment 9.5 Emergency Systems, Signaling, and Fire Alarm Interfaces 9.6 OSHA Electrical Safety, Lockout, and Field Risk Control 9.7 Special Occupancies and Safety Case Lab
10 Chapter 10: Master Electrician Integrated Code and Calculation Labs
10.1 Residential Service Upgrade Integrated Lab 10.2 Small Commercial Tenant Improvement Integrated Lab 10.3 Motor Shop and Industrial Equipment Integrated Lab 10.4 Mixed-Occupancy Special Condition Integrated Lab 10.5 Generator, Transfer, and Emergency Load Integrated Lab 10.6 Plan Review, Redline, and Supervisory Correction Lab 10.7 Five-Hour Open-Book Simulation Strategy
11 Chapter 11: Final Review, Test Day, Licensing, and Business Next Steps
11.1 Final 30-Day Master Electrician Review Plan 11.2 Reference Tab, Index, and Open-Book Speed Drills 11.3 Test-Day Checklist: Pearson VUE, PRONTO, and Retake Rules 11.4 After the Score: Jurisdiction Application and License Next Steps 11.5 Business, Supervision, Permit, and Compliance Readiness 11.6 Master Electrician Final Mixed Review
1.1 ICC R16, T16, G16, and Jurisdiction Variance
Key Takeaways Explain This Topic AI
R16-N, T16-N, and G16-N are ICC National Standard Master Electrician exams tied to different NEC editions, not different license scopes by themselves.
ICC provides exams for licensing agencies; the state, county, city, or board decides whether a passing score satisfies a license requirement.
R16-N is based on the 2023 NEC and 2021 International Codes, T16-N is based on the 2020 NEC and 2018 International Codes, and G16-N is listed as a 2017 NEC master exam.
A master candidate must verify the jurisdiction, exam ID, code cycle, application rules, retake rules, and accepted references before scheduling.
Source control means studying from the bulletin, exam catalog, current ICC exam list, and local board instructions instead of relying on old prep-site summaries.
Last updated: May 2026
ICC exam identity and source control
The ICC National Standard Master Electrician exam is best understood as an exam product used by licensing agencies, not as a nationwide master license. That distinction controls everything else in this guide. ICC develops and administers contractor and trades examinations through Pearson VUE, but a jurisdiction decides whether the exam is required, whether an applicant is eligible to sit, what experience must be documented, what fees are paid to the board, and what happens after a passing result.
For current NEC-centered master exams, the core ICC labels are R16-N, T16-N, and G16-N. R16-N is the Master Electrician exam based on the 2023 National Electrical Code and related 2021 International Codes. T16-N is the Master Electrician exam based on the 2020 NEC and related 2018 International Codes. G16-N is listed in the current ICC national contractor exam list as a Master Electrician exam based on the 2017 NEC. A local board may still use an older exam while another has moved to R16. The title alone is not enough.
A serious candidate treats the exam ID as a controlled document field. Write it at the top of your study plan: exam ID, code edition, jurisdiction, registration bulletin date, reference list, test vendor, question count, time limit, passing score, and any board-specific amendment packet. If one of those fields is unknown, the study plan is not yet controlled. An uncontrolled plan leads to expensive errors, such as studying 2023 NEC dwelling service changes for a 2020 NEC exam, bringing the wrong book, or assuming a passing ICC result automatically creates a license.
Jurisdiction variance is normal. One city may require a master exam for contracting, another may require a state master license, and another may use ICC only as part of a broader application. A county might require proof of experience, insurance, bond, business registration, or continuing education after the exam. Some boards adopt local amendments that affect field work even when the exam itself is based on the unamended listed references. Do not blend those categories. Exam questions come from the listed exam references. Licensing authority comes from the board.
A practical source-control workflow has three layers. First, read the current ICC National Contractor/Trades Examination Information Bulletin and the current ICC national contractor exam list. These answer what ICC is offering, how the exam is administered, and which code cycle is attached to the exam ID. Second, read the jurisdiction's licensing page or application packet. This answers whether the jurisdiction accepts R16, T16, G16, or another exam, and what the applicant must do before and after testing.
Third, read the exam catalog reference list for the exact exam before buying books, tabs, practice tests, or code updates.
Master-level preparation also requires version discipline inside the NEC. The NEC is reorganized in many small ways from cycle to cycle. A rule may move, a table note may change, a definition may be refined, or a dwelling calculation path may be revised. In the exam room, you are not rewarded for knowing that a later edition changed the topic. You are rewarded for answering from the listed source. If your jurisdiction assigned T16, you need the 2020 NEC logic, even if you work under 2023 NEC in the field.
The clean way to avoid cross-cycle confusion is to build a source-control page in your binder or digital notes. Include a table like this:
- Field Controlled entry
- Jurisdiction Board, city, county, or state requiring the exam
- Exam ID R16-N, T16-N, G16-N, or local equivalent
- NEC edition 2023, 2020, 2017, or other assigned edition
- ICC bulletin Publication date and registration rules used
- References Exact books and editions listed for the exam
- License effect What the jurisdiction says a pass does and does not do
Use that page when you evaluate every practice question. If a question references an edition outside your exam, mark it as cross-cycle practice and do not let it rewrite your exam memory. If an online source says all contractor exams pass at 70%, check it against the ICC passing score guidance for Master Electrician. If a forum says candidates can bring loose notes, check the current open-book rules. The habit matters because the exam often tests narrow distinctions, and narrow distinctions are fragile when your sources are mixed.
A final orientation point: the master exam is not just a harder journeyman quiz. It assumes the candidate can supervise installations, evaluate service and feeder design, coordinate grounding and bonding, recognize special occupancy traps, and navigate references efficiently. That level of judgment starts before Article 100. It starts with knowing exactly which exam you are taking and refusing to study from stale or mismatched instructions.