Study guide

2.4 Demand Loads, Continuous Loads, and Calculation Setup

Master Electrician Study Guide Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Master Exam Orientation and Source Control

1.1 ICC R16, T16, G16, and Jurisdiction Variance 1.2 Current Format, Cost, Time, and Passing Score 1.3 Master License Scope vs. Exam Provider 1.4 Official References, Open-Book Rules, and Calculators 1.5 Domain Weights and Master-Level Study Map 1.6 Using the Practice Bank, Error Log, and Code Index

2 Chapter 2: Master-Level Electrical Theory, Plans, and Calculations

2.1 Plan Reading, Specifications, and Supervisory Review 2.2 Ohms Law, Power Factor, and Three-Phase Review 2.3 Fault Current, Available Fault Current, and Equipment Ratings 2.4 Demand Loads, Continuous Loads, and Calculation Setup 2.5 Voltage Drop and Design Judgment 2.6 Coordination, Selectivity, and Master-Level Decision-Making 2.7 Theory, Plans, and Calculation Case Lab

3 Chapter 3: Services, Service Equipment, and Main Distribution

3.1 Service Point, Service Conductors, and Utility Boundaries 3.2 Service Load Calculations and Demand-Factor Workflow 3.3 Service Disconnects, Overcurrent Protection, and Grouping 3.4 Service Equipment Ratings, Clearances, and Working Space 3.5 Transformers and Separately Derived System Decisions 3.6 Temporary Services and Construction Power 3.7 Services and Main Distribution Case Lab

4 Chapter 4: Grounding, Bonding, and Fault-Current Paths

4.1 Grounding vs. Bonding and Exam Language 4.2 Grounding Electrode Systems and Grounding Electrode Conductors 4.3 Main Bonding Jumpers, System Bonding, and Equipment Bonding 4.4 Separately Derived Systems Grounding and Bonding 4.5 Fault-Current Paths, Clearing Time, and Equipment Ratings 4.6 Special Bonding Patterns: Pools, Services, and Metal Systems 4.7 Grounding and Bonding Case Lab

5 Chapter 5: Feeders, Branch Circuits, and Conductor Engineering

5.1 Feeder vs. Branch Boundaries and Load Flow 5.2 Conductor Ampacity, Temperature Ratings, and Terminal Limits 5.3 Adjustment, Correction, and Neutral Counting 5.4 Overcurrent Protection, Tap Conductors, and Next-Size Rules 5.5 Required Outlets, GFCI/AFCI, and Occupancy Patterns 5.6 Multiwire Branch Circuits, Shared Neutrals, and Voltage Drop 5.7 Feeders, Branch Circuits, and Conductor Case Lab

6 Chapter 6: Wiring Methods, Raceways, Box Fill, and Installation Judgment

6.1 Raceway Selection and Installation Conditions 6.2 Raceway Fill, Conductor Protection, and Bending Limits 6.3 Boxes, Enclosures, and Conduit Bodies 6.4 Box Fill: Device Yokes, Equipment Grounds, and Clamps 6.5 Underground, Wet, Corrosive, and Physical-Damage Locations 6.6 Cabinets, Panelboards, Switchboards, and Working Clearance 6.7 Wiring Methods Installation Case Lab

7 Chapter 7: Equipment, Devices, Controls, and Utilization Equipment

7.1 Luminaires, Receptacles, Switches, and Device Placement 7.2 Appliances, Utilization Equipment, and Nameplate Data 7.3 Heating, Cooling, and HVAC Equipment Branch-Circuit Decisions 7.4 Disconnects, Switches, Controllers, and Control-Circuit Logic 7.5 Panelboards, Switchboards, Cabinets, and Equipment Labeling 7.6 Working Space, Accessibility, and Maintenance Judgment 7.7 Equipment, Devices, and Controls Case Lab

8 Chapter 8: Motors, Generators, Transformers, and Power Systems

8.1 Motor Loads, Full-Load Current, and Nameplate Boundaries 8.2 Motor Conductors, Overloads, and Short-Circuit/Ground-Fault Protection 8.3 Motor Controllers, Disconnects, and Group Installations 8.4 Generators, Transfer Equipment, and Optional Standby Systems 8.5 Emergency, Legally Required, and Critical Power Distinctions 8.6 Transformer Primary, Secondary, and Grounding Decisions 8.7 Motors, Generators, and Power Systems Case Lab

9 Chapter 9: Special Occupancies, Emergency Systems, and Safety

9.1 Hazardous Classified Locations and Boundary Thinking 9.2 Healthcare, Places of Assembly, and Commercial Special Rules 9.3 Pools, Spas, Marinas, and Corrosive/Wet Environments 9.4 RV Parks, Mobile Homes, Data Centers, and Special Equipment 9.5 Emergency Systems, Signaling, and Fire Alarm Interfaces 9.6 OSHA Electrical Safety, Lockout, and Field Risk Control 9.7 Special Occupancies and Safety Case Lab

10 Chapter 10: Master Electrician Integrated Code and Calculation Labs

10.1 Residential Service Upgrade Integrated Lab 10.2 Small Commercial Tenant Improvement Integrated Lab 10.3 Motor Shop and Industrial Equipment Integrated Lab 10.4 Mixed-Occupancy Special Condition Integrated Lab 10.5 Generator, Transfer, and Emergency Load Integrated Lab 10.6 Plan Review, Redline, and Supervisory Correction Lab 10.7 Five-Hour Open-Book Simulation Strategy

11 Chapter 11: Final Review, Test Day, Licensing, and Business Next Steps

11.1 Final 30-Day Master Electrician Review Plan 11.2 Reference Tab, Index, and Open-Book Speed Drills 11.3 Test-Day Checklist: Pearson VUE, PRONTO, and Retake Rules 11.4 After the Score: Jurisdiction Application and License Next Steps 11.5 Business, Supervision, Permit, and Compliance Readiness 11.6 Master Electrician Final Mixed Review

2.4 Demand Loads, Continuous Loads, and Calculation Setup

Key Takeaways Explain This Topic AI

Calculation setup must identify occupancy, load type, continuous duration, demand factors, and whether the question asks for load, conductor, or overcurrent sizing.

Continuous-load adjustment is not the same thing as a demand factor, and applying both in the wrong order can change the answer.

Nameplate data, article-specific rules, and dwelling versus non-dwelling treatment often control the calculation path.

A master-level worksheet separates connected load, demand load, neutral load, largest motor, and final conductor or device selection.

Last updated: May 2026

Calculation setup before arithmetic

Demand-load questions are usually won or lost before the first multiplication. The master electrician should first decide what is being sized: service load, feeder load, branch-circuit conductor, neutral, overcurrent device, equipment rating, or a plan-check value. A connected load is the sum of loads connected to the system. A demand load is the load after permitted demand factors or calculation methods are applied.

A continuous load is a load expected to run for a long enough duration that code rules commonly require sizing at 125 percent unless the equipment and assembly are listed for 100 percent operation under the applicable conditions.

Do not mix these ideas. Demand factors recognize diversity. Continuous-load adjustment recognizes heating from sustained current. Motor rules recognize starting and operating characteristics. Transformer rules recognize source and secondary protection. Appliance and HVAC nameplate rules recognize tested equipment. A master-level calculation labels each line so the final answer can be defended.

Worksheet format

Use a worksheet even on scratch paper:

Identify code edition and jurisdiction or exam reference.

Identify occupancy and system voltage.

List each load by category: lighting, receptacle, appliance, cooking, HVAC, motor, continuous, noncontinuous, sign, show window, EV, welder, special equipment.

Convert all loads to VA or amperes on a common voltage basis.

Apply article-specific demand factors where permitted.

Add continuous load treatment where required for conductors and overcurrent devices.

Add largest motor adjustments where required.

Calculate neutral separately when rules allow or require a different value.

Select conductor ampacity after adjustment, correction, terminal temperature, and standard-size device rules are considered.

Check equipment ratings, fault current, voltage drop, and plan notes.

This structure prevents a common exam mistake: answering the wrong question. If the stem asks for calculated load, stop at calculated load. If it asks for minimum conductor ampacity, continue through continuous load and applicable adjustment or correction. If it asks for overcurrent protection, apply the device selection rule. The same project data can produce different correct numbers depending on the target.

Demand factor and continuous-load comparison

Concept Why it exists Typical effect Trap

Connected load Total load connected before diversity. Highest raw total. Treating it as final service load.

Demand factor Recognizes not all loads operate at maximum together. Reduces calculated load when permitted. Applying a demand factor where the article does not allow it.

Continuous-load factor Accounts for sustained heating. Often increases conductor or OCPD sizing basis. Applying it to every load without reading duration.

Largest motor addition Accounts for motor starting and feeder behavior. Adds a percentage of largest motor load in many setups. Adding largest motor twice when it is already included in an HVAC nameplate rule.

Neutral calculation Reflects expected neutral current. May be same, reduced, or specially treated. Reducing nonlinear or specified neutral loads incorrectly.

Example setup

Assume a non-dwelling feeder supplies 42,000 VA of noncontinuous load and 18,000 VA of continuous load at 208 volts, three-phase, and no other demand factors apply. If the question asks for calculated feeder load for sizing conductors under the common continuous-load rule, set it up as 42,000 + 1.25 x 18,000 = 64,500 VA. Convert to current: 64,500 / (1.732 x 208) = about 179 amps. The final conductor and overcurrent selection would then require ampacity table use, terminal temperature review, conductor material, adjustment and correction, and standard device selection.

If the same problem asked only for connected load, the answer would be 60,000 VA. If it asked for real power at a given power factor, that would be a different theory question. If it named specific equipment with minimum circuit ampacity and maximum overcurrent protection, nameplate and equipment article rules might replace the generic setup. The exam stem usually tells you which path is intended.

Dwelling and non-dwelling caution

Dwelling service and feeder calculations contain special methods and demand factors that do not automatically apply to commercial, industrial, or institutional buildings. A range, dryer, dwelling appliance, general lighting load, or HVAC selection may be handled differently depending on whether the installation is a one-family dwelling, multifamily dwelling, hotel, dormitory, restaurant, school, office, store, or other occupancy. Do not import a dwelling demand table into a non-dwelling problem because the numbers look familiar.

Likewise, a commercial kitchen is not a dwelling kitchen. A dormitory room is not always a dwelling unit. A house panel in a multifamily building may carry common-area loads that are not calculated as one dwelling. The master electrician should underline the occupancy words before choosing the article or table.

Field supervision and exam traps

In the field, load calculations support permit submittals, service changes, generator sizing, feeder installation, and equipment procurement. The master electrician should verify that the calculation matches the approved plans and actual equipment. If the owner substitutes a larger water heater, adds EV charging, changes HVAC, or adds kitchen equipment, the load calculation may no longer match the installation.

On the exam, traps include applying 125 percent to noncontinuous loads, forgetting to apply it to continuous loads when sizing conductors or devices, using single-phase formulas for three-phase VA, rounding too early, treating spare breaker spaces as load, and using breaker size as load. Another trap is ignoring the phrase all loads are noncontinuous or all loads are continuous. The correct answer follows the stated facts, not a typical job assumption.