Study guide

2.7 Theory, Plans, and Calculation Case Lab

Master Electrician Study Guide Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Master Exam Orientation and Source Control

1.1 ICC R16, T16, G16, and Jurisdiction Variance 1.2 Current Format, Cost, Time, and Passing Score 1.3 Master License Scope vs. Exam Provider 1.4 Official References, Open-Book Rules, and Calculators 1.5 Domain Weights and Master-Level Study Map 1.6 Using the Practice Bank, Error Log, and Code Index

2 Chapter 2: Master-Level Electrical Theory, Plans, and Calculations

2.1 Plan Reading, Specifications, and Supervisory Review 2.2 Ohms Law, Power Factor, and Three-Phase Review 2.3 Fault Current, Available Fault Current, and Equipment Ratings 2.4 Demand Loads, Continuous Loads, and Calculation Setup 2.5 Voltage Drop and Design Judgment 2.6 Coordination, Selectivity, and Master-Level Decision-Making 2.7 Theory, Plans, and Calculation Case Lab

3 Chapter 3: Services, Service Equipment, and Main Distribution

3.1 Service Point, Service Conductors, and Utility Boundaries 3.2 Service Load Calculations and Demand-Factor Workflow 3.3 Service Disconnects, Overcurrent Protection, and Grouping 3.4 Service Equipment Ratings, Clearances, and Working Space 3.5 Transformers and Separately Derived System Decisions 3.6 Temporary Services and Construction Power 3.7 Services and Main Distribution Case Lab

4 Chapter 4: Grounding, Bonding, and Fault-Current Paths

4.1 Grounding vs. Bonding and Exam Language 4.2 Grounding Electrode Systems and Grounding Electrode Conductors 4.3 Main Bonding Jumpers, System Bonding, and Equipment Bonding 4.4 Separately Derived Systems Grounding and Bonding 4.5 Fault-Current Paths, Clearing Time, and Equipment Ratings 4.6 Special Bonding Patterns: Pools, Services, and Metal Systems 4.7 Grounding and Bonding Case Lab

5 Chapter 5: Feeders, Branch Circuits, and Conductor Engineering

5.1 Feeder vs. Branch Boundaries and Load Flow 5.2 Conductor Ampacity, Temperature Ratings, and Terminal Limits 5.3 Adjustment, Correction, and Neutral Counting 5.4 Overcurrent Protection, Tap Conductors, and Next-Size Rules 5.5 Required Outlets, GFCI/AFCI, and Occupancy Patterns 5.6 Multiwire Branch Circuits, Shared Neutrals, and Voltage Drop 5.7 Feeders, Branch Circuits, and Conductor Case Lab

6 Chapter 6: Wiring Methods, Raceways, Box Fill, and Installation Judgment

6.1 Raceway Selection and Installation Conditions 6.2 Raceway Fill, Conductor Protection, and Bending Limits 6.3 Boxes, Enclosures, and Conduit Bodies 6.4 Box Fill: Device Yokes, Equipment Grounds, and Clamps 6.5 Underground, Wet, Corrosive, and Physical-Damage Locations 6.6 Cabinets, Panelboards, Switchboards, and Working Clearance 6.7 Wiring Methods Installation Case Lab

7 Chapter 7: Equipment, Devices, Controls, and Utilization Equipment

7.1 Luminaires, Receptacles, Switches, and Device Placement 7.2 Appliances, Utilization Equipment, and Nameplate Data 7.3 Heating, Cooling, and HVAC Equipment Branch-Circuit Decisions 7.4 Disconnects, Switches, Controllers, and Control-Circuit Logic 7.5 Panelboards, Switchboards, Cabinets, and Equipment Labeling 7.6 Working Space, Accessibility, and Maintenance Judgment 7.7 Equipment, Devices, and Controls Case Lab

8 Chapter 8: Motors, Generators, Transformers, and Power Systems

8.1 Motor Loads, Full-Load Current, and Nameplate Boundaries 8.2 Motor Conductors, Overloads, and Short-Circuit/Ground-Fault Protection 8.3 Motor Controllers, Disconnects, and Group Installations 8.4 Generators, Transfer Equipment, and Optional Standby Systems 8.5 Emergency, Legally Required, and Critical Power Distinctions 8.6 Transformer Primary, Secondary, and Grounding Decisions 8.7 Motors, Generators, and Power Systems Case Lab

9 Chapter 9: Special Occupancies, Emergency Systems, and Safety

9.1 Hazardous Classified Locations and Boundary Thinking 9.2 Healthcare, Places of Assembly, and Commercial Special Rules 9.3 Pools, Spas, Marinas, and Corrosive/Wet Environments 9.4 RV Parks, Mobile Homes, Data Centers, and Special Equipment 9.5 Emergency Systems, Signaling, and Fire Alarm Interfaces 9.6 OSHA Electrical Safety, Lockout, and Field Risk Control 9.7 Special Occupancies and Safety Case Lab

10 Chapter 10: Master Electrician Integrated Code and Calculation Labs

10.1 Residential Service Upgrade Integrated Lab 10.2 Small Commercial Tenant Improvement Integrated Lab 10.3 Motor Shop and Industrial Equipment Integrated Lab 10.4 Mixed-Occupancy Special Condition Integrated Lab 10.5 Generator, Transfer, and Emergency Load Integrated Lab 10.6 Plan Review, Redline, and Supervisory Correction Lab 10.7 Five-Hour Open-Book Simulation Strategy

11 Chapter 11: Final Review, Test Day, Licensing, and Business Next Steps

11.1 Final 30-Day Master Electrician Review Plan 11.2 Reference Tab, Index, and Open-Book Speed Drills 11.3 Test-Day Checklist: Pearson VUE, PRONTO, and Retake Rules 11.4 After the Score: Jurisdiction Application and License Next Steps 11.5 Business, Supervision, Permit, and Compliance Readiness 11.6 Master Electrician Final Mixed Review

2.7 Theory, Plans, and Calculation Case Lab

Key Takeaways Explain This Topic AI

Case-style questions require combining plan reading, theory, demand calculation, fault-current review, and supervisory judgment.

A master-level answer documents assumptions, identifies the controlling article path, and separates calculated load from equipment rating decisions.

The correct workflow often matters more than a memorized number because the same project data can support several different questions.

Field-quality review includes asking whether substitutions, available fault current, voltage drop, and coordination requirements still match the approved design.

Last updated: May 2026

Case setup

Assume you are reviewing a small commercial tenant improvement. The service is 480Y/277 volts, three-phase, 4-wire, feeding a 225 amp panel. A 45 kVA transformer supplies a 208Y/120 volt panel for receptacles and small equipment. The one-line shows 18 kA available fault current at the service switchboard and 9 kA at the 208Y/120 volt panel. The specification requires copper conductors, listed equipment, permanent circuit identification, and a coordination review for the emergency lighting inverter feeder.

The plans include lighting, receptacles, one rooftop unit, a small motor load, and an emergency lighting inverter.

This is the kind of mixed fact pattern that appears in master-level work. The exam version may be shorter, but it tests the same habits. The field version has more documents, more substitutions, and more people making assumptions. Your task is to separate the facts into plan review, theory, load calculation, fault-current rating, voltage drop, and coordination decisions.

Step 1: Build the document map

Start by matching the one-line to the schedules. Confirm the service voltage, panel names, transformer size, feeder sizes, overcurrent device ratings, and available fault-current notes. Check whether the 225 amp panel schedule actually carries a load that requires 225 amps or whether 225 amps is only the equipment rating. Check whether the transformer primary and secondary conductors are shown and whether secondary protection is addressed. Confirm that emergency lighting inverter circuits are separated and identified as required by the applicable system rules and project documents.

Then read specifications for requirements that drawings might not show in every symbol. Copper-only conductors change conductor selection. Coordination review changes submittal requirements. Equipment SCCR and interrupting ratings must match available fault current. If the plan says 9 kA available at the 208Y/120 panel, a 10 kA rated panel and breakers may be acceptable from an interrupting-rating standpoint if no higher value applies at that point, but downstream equipment SCCR still needs checking. If utility or transformer changes increase available fault current, the gear may no longer match.

Step 2: Do theory checks

For the 45 kVA, 208 volt, three-phase transformer secondary, full-load current is 45,000 / (1.732 x 208), or about 125 amps. The primary current at 480 volts is 45,000 / (1.732 x 480), or about 54 amps. These are base theory currents, not final protection answers. Transformer primary and secondary protection, conductor sizing, and grounding or bonding details require the transformer article and related rules.

If the rooftop unit nameplate gives minimum circuit ampacity and maximum overcurrent protection, use those values for that equipment instead of recalculating from horsepower or kW unless the question specifically asks for a theory conversion. If a motor load is listed by horsepower, navigate to motor full-load current tables and motor circuit rules rather than using nameplate current for every code purpose. If the emergency lighting inverter has input and output ratings, identify whether you are sizing the supply circuit, the output circuits, or the emergency system distribution path.

Step 3: Organize load calculation

Create a load table. List lighting at the voltage and load basis shown. List receptacles and apply the permitted calculation method for the occupancy. List HVAC from nameplate or calculation rules. List motors and identify the largest motor if a feeder rule requires an additional percentage. Identify continuous loads, such as lighting expected to operate continuously, and noncontinuous loads. Add demand factors only where the applicable article permits them.

A sample line might read: general lighting, 12,000 VA, continuous; receptacles, 18,000 VA connected, demand method to be verified; rooftop unit, use nameplate MCA and MOCP; motor, use table FLC for feeder calculation; emergency inverter, verify continuous input load and system article. This line-by-line labeling is more important than mental arithmetic. It tells the reviewer what rule applies and prevents double-counting. Do not add the largest motor twice if an equipment nameplate or HVAC rule has already built in the relevant sizing basis.

Step 4: Check fault current and ratings

At the service switchboard, equipment interrupting ratings must be at least 18 kA unless a listed series combination or other approved design is used. If the specification requires fully rated equipment, each device must individually meet the available fault current at its line terminals. At the 208Y/120 panel with 9 kA available, 10 kA equipment may be adequate for interrupting rating, but verify panel SCCR, breakers, and any downstream equipment. If the transformer is replaced with a lower-impedance unit or located closer to the panel, available fault current can increase.

For industrial control panels, HVAC equipment, transfer switches, and inverter equipment, read SCCR labels. A 10 kA breaker feeding a 5 kA SCCR control panel does not magically make the control panel suitable for 9 kA available fault current unless listed current-limiting protection and manufacturer instructions establish the rating. The master-level move is to compare every relevant label to the available value at that point.

Step 5: Voltage drop and coordination

Suppose the emergency lighting inverter feeder is 180 feet one way and carries 32 amps at 480 volts, three-phase. Using an ohms-per-thousand-feet method, you would identify conductor resistance, then calculate approximate drop as 1.732 x I x R x D / 1000. If the result is too high for the specification or equipment instructions, consider larger conductors, a shorter route, a different panel location, or adjusted distribution. Do not confuse this design change with a lower load calculation.

Coordination review for the emergency lighting inverter feeder means checking device behavior, not only ratings. The branch or feeder device nearest a fault should operate as required by the applicable emergency system rule or specification. Review time-current curves, settings, and manufacturer data. If a series-rated combination is proposed, verify that it is allowed by the project requirement and that it does not conflict with required selectivity.

Step 6: Exam answer discipline

For a case-style exam problem, write a five-line scratch outline: documents, theory, load, fault, coordination. Then answer only the question asked. If it asks for transformer secondary current, calculate about 125 amps and stop. If it asks whether 10 kA equipment is acceptable at a point with 18 kA available, answer no unless a listed series design is stated. If it asks why the emergency feeder needs special review, discuss selective coordination or system reliability rather than ordinary room receptacle layout.

The final habit is to avoid global claims. ICC master electrician exams use four-option multiple-choice questions and published references, but licensure is determined by the jurisdiction. The master electrician's job is to use the correct code edition, follow the adopted local rules, document assumptions, and supervise the installation so the built work matches the approved design.

Structured Decision Aid

Read the plan note, equipment schedule, one-line diagram, and load description before touching formulas.

Identify system voltage, phase, continuous load status, and equipment ratings before selecting conductors or OCPD.

Write the calculation sequence in order: load, demand, ampacity, adjustment/correction, terminal limit, OCPD, grounding.

Check whether the exam asks for minimum code compliance, good design judgment, or a supervisory correction.