Study guide

6.4 Box Fill: Device Yokes, Equipment Grounds, and Clamps

Master Electrician Study Guide Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Master Exam Orientation and Source Control

1.1 ICC R16, T16, G16, and Jurisdiction Variance 1.2 Current Format, Cost, Time, and Passing Score 1.3 Master License Scope vs. Exam Provider 1.4 Official References, Open-Book Rules, and Calculators 1.5 Domain Weights and Master-Level Study Map 1.6 Using the Practice Bank, Error Log, and Code Index

2 Chapter 2: Master-Level Electrical Theory, Plans, and Calculations

2.1 Plan Reading, Specifications, and Supervisory Review 2.2 Ohms Law, Power Factor, and Three-Phase Review 2.3 Fault Current, Available Fault Current, and Equipment Ratings 2.4 Demand Loads, Continuous Loads, and Calculation Setup 2.5 Voltage Drop and Design Judgment 2.6 Coordination, Selectivity, and Master-Level Decision-Making 2.7 Theory, Plans, and Calculation Case Lab

3 Chapter 3: Services, Service Equipment, and Main Distribution

3.1 Service Point, Service Conductors, and Utility Boundaries 3.2 Service Load Calculations and Demand-Factor Workflow 3.3 Service Disconnects, Overcurrent Protection, and Grouping 3.4 Service Equipment Ratings, Clearances, and Working Space 3.5 Transformers and Separately Derived System Decisions 3.6 Temporary Services and Construction Power 3.7 Services and Main Distribution Case Lab

4 Chapter 4: Grounding, Bonding, and Fault-Current Paths

4.1 Grounding vs. Bonding and Exam Language 4.2 Grounding Electrode Systems and Grounding Electrode Conductors 4.3 Main Bonding Jumpers, System Bonding, and Equipment Bonding 4.4 Separately Derived Systems Grounding and Bonding 4.5 Fault-Current Paths, Clearing Time, and Equipment Ratings 4.6 Special Bonding Patterns: Pools, Services, and Metal Systems 4.7 Grounding and Bonding Case Lab

5 Chapter 5: Feeders, Branch Circuits, and Conductor Engineering

5.1 Feeder vs. Branch Boundaries and Load Flow 5.2 Conductor Ampacity, Temperature Ratings, and Terminal Limits 5.3 Adjustment, Correction, and Neutral Counting 5.4 Overcurrent Protection, Tap Conductors, and Next-Size Rules 5.5 Required Outlets, GFCI/AFCI, and Occupancy Patterns 5.6 Multiwire Branch Circuits, Shared Neutrals, and Voltage Drop 5.7 Feeders, Branch Circuits, and Conductor Case Lab

6 Chapter 6: Wiring Methods, Raceways, Box Fill, and Installation Judgment

6.1 Raceway Selection and Installation Conditions 6.2 Raceway Fill, Conductor Protection, and Bending Limits 6.3 Boxes, Enclosures, and Conduit Bodies 6.4 Box Fill: Device Yokes, Equipment Grounds, and Clamps 6.5 Underground, Wet, Corrosive, and Physical-Damage Locations 6.6 Cabinets, Panelboards, Switchboards, and Working Clearance 6.7 Wiring Methods Installation Case Lab

7 Chapter 7: Equipment, Devices, Controls, and Utilization Equipment

7.1 Luminaires, Receptacles, Switches, and Device Placement 7.2 Appliances, Utilization Equipment, and Nameplate Data 7.3 Heating, Cooling, and HVAC Equipment Branch-Circuit Decisions 7.4 Disconnects, Switches, Controllers, and Control-Circuit Logic 7.5 Panelboards, Switchboards, Cabinets, and Equipment Labeling 7.6 Working Space, Accessibility, and Maintenance Judgment 7.7 Equipment, Devices, and Controls Case Lab

8 Chapter 8: Motors, Generators, Transformers, and Power Systems

8.1 Motor Loads, Full-Load Current, and Nameplate Boundaries 8.2 Motor Conductors, Overloads, and Short-Circuit/Ground-Fault Protection 8.3 Motor Controllers, Disconnects, and Group Installations 8.4 Generators, Transfer Equipment, and Optional Standby Systems 8.5 Emergency, Legally Required, and Critical Power Distinctions 8.6 Transformer Primary, Secondary, and Grounding Decisions 8.7 Motors, Generators, and Power Systems Case Lab

9 Chapter 9: Special Occupancies, Emergency Systems, and Safety

9.1 Hazardous Classified Locations and Boundary Thinking 9.2 Healthcare, Places of Assembly, and Commercial Special Rules 9.3 Pools, Spas, Marinas, and Corrosive/Wet Environments 9.4 RV Parks, Mobile Homes, Data Centers, and Special Equipment 9.5 Emergency Systems, Signaling, and Fire Alarm Interfaces 9.6 OSHA Electrical Safety, Lockout, and Field Risk Control 9.7 Special Occupancies and Safety Case Lab

10 Chapter 10: Master Electrician Integrated Code and Calculation Labs

10.1 Residential Service Upgrade Integrated Lab 10.2 Small Commercial Tenant Improvement Integrated Lab 10.3 Motor Shop and Industrial Equipment Integrated Lab 10.4 Mixed-Occupancy Special Condition Integrated Lab 10.5 Generator, Transfer, and Emergency Load Integrated Lab 10.6 Plan Review, Redline, and Supervisory Correction Lab 10.7 Five-Hour Open-Book Simulation Strategy

11 Chapter 11: Final Review, Test Day, Licensing, and Business Next Steps

11.1 Final 30-Day Master Electrician Review Plan 11.2 Reference Tab, Index, and Open-Book Speed Drills 11.3 Test-Day Checklist: Pearson VUE, PRONTO, and Retake Rules 11.4 After the Score: Jurisdiction Application and License Next Steps 11.5 Business, Supervision, Permit, and Compliance Readiness 11.6 Master Electrician Final Mixed Review

6.4 Box Fill: Device Yokes, Equipment Grounds, and Clamps

Key Takeaways Explain This Topic AI

Box fill is a counting method: each conductor or item is assigned volume based on the largest conductor involved under the applicable rule.

Device yokes, internal clamps, support fittings, and equipment grounding conductors are the common missed allowances.

Pigtails that originate and terminate in the same box are usually treated differently from conductors that enter or leave the box.

The largest conductor associated with a device yoke or internal item can control the volume allowance.

Last updated: May 2026

The Box Fill Mindset

Box fill is one of the most reliable places for an exam to separate memorization from code practice. The math is not difficult. The difficulty is translating a messy device box into counted volume allowances. Every conductor that enters, leaves, passes through, originates outside, terminates inside, or is spliced inside may affect fill. Devices, yokes, internal clamps, fixture studs, support fittings, and equipment grounding conductors add volume even though they are not load conductors.

The rule is not asking whether the installer can physically cram the conductors into the box. It is asking whether the box provides enough free space to prevent damage, overheating, and unsafe device pressure. If the device must be forced into place, if wirenuts are crushed behind a receptacle, or if grounding pigtails are the only reason the device fits, the workmanship concern is pointing to the same safety purpose as the fill rule.

Box Fill Counting Table

Item In Box Typical Counting Concept Common Trap

Conductor entering and terminating or spliced Counts as one volume allowance for its size Forgetting neutral or switched leg conductors.

Conductor passing through unbroken Counts according to the rule for pass-through conductors Assuming only spliced conductors count.

Pigtail entirely within the box Often not counted as a separate conductor allowance Counting every short pigtail and oversizing the result on the exam.

Equipment grounding conductors Count together under the grounding-conductor rule Counting every grounding conductor as a full separate allowance when the rule groups them.

Device yoke Counts as conductor volume based on conductors connected to it Forgetting two allowances for a strap-mounted device when required.

Internal cable clamps Count if internal to the box Counting external clamps, or ignoring internal clamps.

Fixture studs or hickeys Count when present under the support fitting rule Missing them because they are mechanical rather than electrical.

Always confirm the exact edition language for the exam you are taking. R16 uses the 2023 NEC, T16 uses the 2020 NEC, and G16 is tied to the 2017 NEC in the current national listing. The concepts are similar, but edition differences can affect wording and examples. The safe study method is to mark the box fill rule and the volume-per-conductor table in the edition listed for your exam.

Worked Setup

Suppose a metal 4-inch square box contains two 12/2 cables with equipment grounding conductors and one duplex receptacle. The ungrounded and grounded circuit conductors enter and are spliced or terminated. The equipment grounding conductors are spliced with a pigtail to the device and box. The duplex receptacle is mounted on one yoke. If the box has internal clamps, they add a volume allowance. The pigtail that stays entirely inside the box normally does not add another entering conductor count.

The setup is more important than the arithmetic:

Count insulated conductors entering or leaving the box.

Apply the equipment grounding conductor allowance correctly.

Add device yoke allowance based on the largest conductor connected to the device.

Add internal clamp allowance if the clamps are inside the box.

Multiply total allowances by the cubic-inch value for the largest conductor involved in each allowance.

Compare to the box marking or listed volume, including any extension ring volume when applicable.

Device Yokes

A device yoke is easy to miss because it looks like hardware, not a conductor. The yoke takes space and forces conductors to bend around it. A duplex receptacle on one strap is one yoke. Two separate switches on separate yokes are counted separately. A multi-gang box with dimmers, GFCI devices, smart switches, or large controls can become crowded fast. The device allowance is based on conductors connected to the device, and the largest conductor involved can control the allowance.

This is a field-quality issue. Modern devices are often deeper than older switches. A box that was technically adequate for a shallow toggle may be a poor choice for a smart dimmer with several conductors, grounding pigtails, and cable clamps. The code minimum volume is only the floor. A master electrician supervising remodel work should recognize when an old box needs replacement or extension rather than forcing a device into an unsafe space.

Equipment Grounds And Bonding Pigtails

Equipment grounding conductors are often mishandled in box fill calculations. They do count, but not always as one full allowance each. The rule groups grounding conductors in a specific way, and additional isolated or separate grounding conductors may affect the count depending on the arrangement and edition. For exam purposes, read whether the grounding conductors are all equipment grounding conductors, whether isolated grounding is involved, and whether bonding jumpers remain entirely within the box.

Bonding the metal box is separate from counting the volume. A box can be large enough but improperly bonded. A box can be bonded but overfilled. Do not let one compliance point distract from the other.

Internal Clamps And Fittings

Internal clamps are another frequent trap. If the clamp is inside the box, it occupies volume and must be counted under the box fill rule. If the clamp is outside and not occupying box space, it is handled differently. Many questions quietly state nonmetallic box with integral clamps or metal box with internal cable clamps. That phrase is a signal. Look for support fittings too, especially in luminaire boxes.

Exam Tactics

Draw the box. Mark each cable entry. Write conductor sizes beside each entry. Put a small circle for each device yoke and a small C for internal clamps. Then count in categories instead of counting randomly across the picture. Random counting causes double counting and missed items.

When answer choices are close, the missed item is usually one yoke allowance, internal clamps, or equipment grounding conductors. When answer choices are far apart, the error is often using the wrong conductor size volume or counting pigtails incorrectly. The best master-level habit is to write the count formula before multiplying. For example: insulated conductors plus grounding allowance plus yoke allowance plus internal clamp allowance equals total volume units. Then multiply by the conductor volume value and compare to the marked box capacity.

In the field, leave enough conductor length for devices and splices while still respecting box volume. Cutting conductors short to make an overfilled box close creates a second violation and makes maintenance dangerous. Correct the enclosure size instead of hiding the problem behind the device plate.