Study guide

10.2 Fall Protection, Trenching, and Scaffolds

Maryland General Contractor Exam Exam

Track your progress as you read

Finished sections get a check mark.

1 Exam Overview and Maryland Licensing Landscape

1.1 Current Exam Facts 1.2 How Maryland Licenses Contractors 1.3 What Counts as Home Improvement

2 Licensing Categories and Qualifications

2.1 Contractor and Salesperson Licenses 2.2 Experience and Character Requirements 2.3 Financial Solvency, Credit Reports, and Surety Bonds 2.4 Insurance Requirements

3 Fees, Renewal, and License Maintenance

3.1 Application Process and Current Fees 3.2 The Two-Year License Cycle 3.3 Displaying the License and Advertising Rules

4 Home Improvement Contract Requirements

4.1 Mandatory Contract Contents 4.2 Deposits and Payment Rules 4.3 Required Notices, Mortgage Clauses, and Arbitration 4.4 Special Rules: Rooftop Solar and Insurance-Claim Work

5 Guaranty Fund, Penalties, and Enforcement

5.1 The Home Improvement Guaranty Fund 5.2 Prohibited Acts and Criminal Penalties 5.3 Complaints, Mediation, and Discipline

6 Door-to-Door Sales Act

6.1 The Right to Cancel 6.2 How Cancellation Works and Exceptions

7 Construction Contract Law Essentials

7.1 Contract Types: Stipulated Sum, Cost-Plus, Unit Price 7.2 Formation and Essential Clauses 7.3 Change Orders, Completion, and Warranties 7.4 Disputes and Subcontractor Agreements

8 Mechanic's Liens and Surety Bonds

8.1 Maryland Mechanic's Lien Law 8.2 Establishing and Defending Liens 8.3 Surety Bonds in Construction

9 Labor and Employment Law

9.1 Employees vs Independent Contractors 9.2 Payroll, Withholding, and Unemployment 9.3 Prevailing Wage and Public Work

10 Safety Regulations and Building Codes

10.1 OSHA Employer Duties and Enforcement 10.2 Fall Protection, Trenching, and Scaffolds 10.3 Hazard Communication and Lead Paint 10.4 Building Codes and Permits in Maryland

11 Estimating, Project Management, and Business Finance

11.1 Construction Estimating 11.2 Scheduling and Project Management 11.3 Job Costing and Financial Management 11.4 Business Formation and Maryland Taxes

10.2 Fall Protection, Trenching, and Scaffolds

Key Takeaways Explain This Topic AI

Construction fall protection is required at 6 feet (29 CFR 1926 Subpart M); guardrail top rails sit at 42 inches plus or minus 3 inches with a midrail halfway up

Scaffolds require guardrails or a personal fall arrest system at 10 feet and must support four times the maximum intended load

Trenches 5 feet or deeper require a protective system — sloping, shoring, or shielding — and a competent person must inspect daily and after every hazard-increasing event such as rain

Soil type drives sloping angles: Type A at 3/4H:1V, Type B at 1H:1V, Type C at 1.5H:1V; previously disturbed soil is never Type A

Ladders in trenches 4 feet or deeper must be within 25 feet of lateral travel, and spoils must sit at least 2 feet back from the excavation edge

Last updated: July 2026

Fall Protection: The 6-Foot Rule

Falls are the leading cause of construction deaths and the most-cited OSHA violation year after year. 29 CFR 1926 Subpart M requires fall protection whenever construction employees work on walking/working surfaces with an unprotected side or edge 6 feet or more above a lower level. Memorize the trigger heights as a set, because the exam loves to mix them:

  • Situation Trigger height
  • General construction walking/working surfaces 6 feet
  • Scaffolds 10 feet
  • Steel erection 15 feet (with limited connector exceptions up to 30 feet)
  • Fixed ladders Fall protection required at 24 feet
  • General industry (for contrast, not construction) 4 feet

The three accepted systems are guardrails , safety nets , and personal fall arrest systems (PFAS) . For guardrails, the top rail is 42 inches plus or minus 3 inches above the walking surface, the midrail sits halfway between the top rail and the surface (about 21 inches), and toe boards at least 3.5 inches high are required where workers or the public pass below. Top rails must withstand a 200-pound force applied outward or downward without failing.

A PFAS consists of an anchorage, full-body harness, and connector (lanyard or self-retracting lifeline). Key numbers: anchorages must hold 5,000 pounds per attached employee or be designed with a 2:1 safety factor ; maximum arresting force on the body is 1,800 pounds ; free fall is limited to 6 feet . Body belts are not acceptable as part of a PFAS. For roofing on low-slope roofs , a warning line system may be used, set at least 6 feet back from the roof edge , often combined with a safety monitoring system. Any floor hole must be covered and the cover secured, marked, and able to support twice the expected load.

Common Exam Traps on Falls

Six feet applies to construction ; four feet is the general-industry number. A question set in a home remodel is construction.

Ten feet is the scaffold number, not the general construction number — the two are swapped constantly in distractors.

A competent or qualified person must inspect PFAS components before each use ; a harness involved in an arrested fall is removed from service.

Trenching and Excavation: The 5-Foot Rule

29 CFR 1926 Subpart P governs excavations. A protective system is required in any trench 5 feet or deeper , unless the excavation is entirely in stable rock. Below 5 feet, a protective system is still required if the competent person finds evidence of a potential cave-in — for example, in loose or previously disturbed soil. One cubic yard of soil weighs roughly 3,000 pounds , which is why cave-ins are so often fatal.

The three protective options:

Sloping or benching — cutting the walls back at an angle tied to soil type: Type A soil at 3/4H:1V (53 degrees) , Type B at 1H:1V (45 degrees) , Type C at 1.5H:1V (34 degrees) . Type C is the default when soil is not tested; previously disturbed soil can never be Type A , which matters on nearly every home-improvement dig next to an existing foundation.

Shoring — timber or hydraulic supports that brace the walls.

Shielding — a trench box that protects workers if the walls fail; workers must stay inside it.

The competent person is central to Subpart P: someone capable of identifying existing and predictable hazards and authorized to take prompt corrective action . That person must classify the soil, choose the protective system, and inspect the excavation daily before the shift starts, and after every rainstorm or other hazard-increasing event . Other testable rules: in trenches 4 feet or deeper , a ladder or ramp must be within 25 feet of lateral travel ; spoil piles and equipment must sit at least 2 feet back from the edge ; no employee works beneath raised loads; and excavations 4 feet or deeper get atmospheric testing where a hazardous atmosphere could reasonably exist (near gas lines, sewers, or landfills).

Scenario the Exam Likes

A crew digs a 6-foot footing trench alongside an existing Baltimore rowhouse — soil that was disturbed decades ago. There is no ladder, spoils sit at the edge, and nobody inspected after last night's rain. Every element is a violation: protective system required (5-foot rule, and the soil cannot be Type A), competent-person inspection required daily and after rain, spoils 2 feet back, and a ladder within 25 feet. Expect a question asking you to count or identify the violations.

Ladders and Scaffolds

Ladders (Subpart X): extension and straight ladders are pitched at about a 4:1 angle (one foot out for every four feet up) and must extend 3 feet above the upper landing for access. Maintain three-point contact , face the ladder, never stand on the top step or top cap of a stepladder, and never use a metal ladder near energized electrical work. Ladders must be inspected before use and defective ones tagged and removed.

Scaffolds (Subpart L) have their own rulebook:

Fall protection — guardrails or a PFAS — is required at 10 feet , not 6.

Scaffolds and components must support at least four times the maximum intended load .

Platforms must be fully planked between uprights, with minimal gaps.

Guardrails are required on all open sides and ends; scaffold top rails installed after the relevant updates must be at least 38 inches (the 42-inch figure belongs to general guardrails).

Safe access (ladder, stairway, or built-in climbing frame) is required; climbing cross braces is prohibited.

Scaffolds must be erected, moved, dismantled, or altered only under the supervision of a competent person , and inspected by that person before each shift.

Never use boxes, blocks, or ladders on top of a scaffold platform to gain height, and never work on scaffolds during storms or high winds.

Mobile scaffolds must have casters locked while in use, and workers may not ride a moving scaffold unless specific conditions are met. For aerial lifts: a scissor lift is treated like a scaffold — its guardrail system is the fall protection — while occupants of a boom lift must wear a harness tied off to the boom or basket. These distinctions appear often because home-improvement contractors rent lifts for siding, roofing, and gutter work.