Study guide
11.3 Duct Hangers, Supports, Insulation & Fire/Smoke Dampers
Maryland HVAC Contractor License Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Maryland HVACR Licensing Framework & Board Jurisprudence
1.1 Maryland HVACR Board Authority, Scope & Statutory Framework 1.2 License Classifications, Scopes & Experience Prerequisites 1.3 Mandatory Insurance, Advertising & Business Regulations 1.4 Examination Logistics, Reciprocity & Board Disciplinary Actions
2 Chapter 2: Electrical Fundamentals, Circuits & Schematics
2.1 Electrical Principles, Ohm's Law & Power Calculations 2.2 Low-Voltage Control Circuits & Transformers 2.3 Electrical Schematics, Ladder Diagrams & Wiring Symbols 2.4 Electrical Test Instruments, Troubleshooting & Diagnostics
3 Chapter 3: Electric Motors & HVACR Control Devices
3.1 Electric Motor Types & Operating Characteristics 3.2 Motor Starting Components & Capacitors 3.3 Operational Controls, Contactors, Relays & Safety Limits
4 Chapter 4: Piping Systems, Materials & Code Installation Standards
4.1 Piping Materials, Sizing & Code Specifications 4.2 Joining Methods, Soldering, Brazing & Mechanical Fittings 4.3 Pipe Hangers, Supports & Vibration Isolation 4.4 Valves, Flow Controls & Piping Insulation
5 Chapter 5: Piping Testing, Hydronic Loop Design & Commissioning
5.1 Pressure Testing, Leak Detection & Code Inspection 5.2 Hydronic Piping Arrangements & Flow Dynamics 5.3 Hydronic Loop Accessories & Expansion Tanks
6 Chapter 6: Thermodynamics, Psychrometrics & The Refrigeration Cycle
6.1 Fundamentals of Heat Transfer & Thermodynamics 6.2 The Vapor-Compression Refrigeration Cycle 6.3 Psychrometric Principles & Chart Analysis 6.4 Psychrometric Diagnostic Applications
7 Chapter 7: Refrigerants, Environmental Regulations & EPA Section 608
7.1 Refrigerant Classifications, Chemistry & ASHRAE Safety Designations 7.2 Temperature Glide, Fractionation & Blends 7.3 Refrigerant Lubricants & Oil Management 7.4 EPA Section 608 Compliance & Recovery Standards
8 Chapter 8: Air Conditioning & Heat Pump Systems
8.1 ACCA Manual J Load Calculations & Manual S Equipment Sizing 8.2 Major System Components & Metering Devices 8.3 Heat Pump Operation, Reversing Valves & Defrost Cycles 8.4 AC & Heat Pump Installation, Charging & System Diagnostics
9 Chapter 9: Gas Heating Systems, Combustion Science & Venting
9.1 Combustion Science, Fuel Gas Properties & Burner Operation 9.2 Gas Furnace Components, Controls & Sequence of Operation 9.3 Gas Piping Sizing, Materials & Installation 9.4 Chimneys, Vents & Flue Gas Sizing
10 Chapter 10: Boilers, Hydronic Heating & Oil-Fired Systems
10.1 Low-Pressure Steam & Hydronic Boilers 10.2 Hydronic Heating Controls, Circulator Pumps & Zone Systems 10.3 Fuel Oil Burners, Storage & Supply Systems
11 Chapter 11: Air Distribution Systems, Duct Design & Ventilation
11.1 Air Distribution Fundamentals & ACCA Manual D 11.2 Duct Construction, Materials & SMACNA Standards 11.3 Duct Hangers, Supports, Insulation & Fire/Smoke Dampers 11.4 Commercial Exhaust, Kitchen Hoods & Building Ventilation
12 Chapter 12: Testing, Air Balancing & Construction Safety
12.1 Airflow Measurement, Testing & System Balancing (TAB) 12.2 Jobsite Safety, OSHA 1926 Standards & Fall Protection 12.3 Electrical Safety, PPE, Hazard Communication & SDS
11.3 Duct Hangers, Supports, Insulation & Fire/Smoke Dampers
Key Takeaways Explain This Topic AI
2018 IMC § 603.10 defers duct supports to SMACNA and manufacturer instructions; it does not contain a universal support-spacing table numbered 603.10.
Under 2015/2018 IECC R403.3.1, both supply and return ducts in attics require R-8 at 3 inches or greater diameter and R-6 below 3 inches; other locations use R-6 and R-4.2 respectively.
Dynamic fire dampers are listed to close against airflow at marked velocity and pressure, while static dampers rely on the system airflow stopping before closure.
2018 IMC § 607.4 requires approved access large enough for inspection and maintenance plus permanent 0.5-inch identification; it does not set a universal 12-by-12-inch minimum.
Last updated: September 2026
Duct Supports, Insulation and Fire/Smoke Dampers
Edition rule: for the 2018 IMC, § 603.10 defers duct support to SMACNA and factory-made-duct manufacturer instructions. Section 607.4 requires access large enough for inspection and maintenance but does not prescribe a 12-inch-square minimum.
1. Structural Support
Supports transfer duct dead load, insulation weight, access loads, and vibration to building structure without crushing or distorting the air passage. Never support duct from ceiling grid, piping, conduit, or another system unless an approved design specifically permits it.
2018 IMC § 603.10 does not contain a “Table 603.10” with universal 10-foot and 16-foot limits. It requires duct support under the SMACNA HVAC Duct Construction Standards—Metal and Flexible and requires flexible and other factory-made ducts to follow manufacturer instructions.
Support selection therefore considers:
Duct shape, material, dimensions, and pressure class.
Horizontal or vertical orientation.
Joint and reinforcement spacing.
Weight of lining, external insulation, dampers, access doors, and accessories.
Seismic restraint and local structural requirements.
Manufacturer instructions for listed factory-made duct.
Trapeze supports for rectangular duct distribute load across the bottom without deforming it. Round duct may use approved bands or trapezes wide enough to prevent distortion. Vertical risers need structural support at floors or intervals determined by the applicable table. Flexible duct needs supports that do not pinch the core or compress insulation. A familiar spacing value is not proof until it is matched to the governing standard or product instructions.
2. Residential Duct Insulation
For the residential prescriptive rule in 2015 and 2018 IECC § R403.3.1:
Supply and return ducts in attics are insulated to at least R-8 when 3 inches or more in diameter and R-6 when less than 3 inches.
Supply and return ducts in other portions of the building are insulated to at least R-6 when 3 inches or more in diameter and R-4.2 when less than 3 inches.
Duct or duct portions completely inside the building thermal envelope are excepted.
The attic rule applies equally to supply and return. “R-8 supply and R-6 return” is not the 2015/2018 prescriptive text. The diameter threshold also matters.
Commercial requirements depend on duct use, location, climate zone, temperature difference, and the adopted commercial energy-code table. Do not transfer the residential attic values to every commercial duct.
Insulation must be installed at its rated thickness. A compressed blanket has less thermal resistance and can create cold bridges. Close butt joints, restore the vapor retarder continuously, seal penetrations, and keep hangers from crushing the insulation where the listed system requires exterior support or saddles.
IMC § 604 contains condensation-control and insulation provisions for ducts conveying air capable of producing condensation. The vapor retarder goes on the warm-in-winter/high-vapor-pressure side appropriate to the assembly and climate. Exterior duct and insulation also require weather protection under § 603.16. Choose jackets, coatings, and fasteners rated for sunlight, water, wind, and service temperature.
3. Fire Dampers and Smoke Dampers
A fire damper protects a fire-resistance-rated assembly where duct penetration protection is required. Under 2018 IMC § 607.3.1 it is listed to UL 555. A smoke damper controls smoke movement and is listed to UL 555S. A combination damper meets both listings.
Section 607.3.2.1 assigns fire-damper ratings:
A 1.5-hour damper for an assembly rated less than 3 hours.
A 3-hour damper for an assembly rated 3 hours or more.
A static fire damper is listed to close when system airflow stops. A dynamic fire damper is listed and rated to close against moving air at its marked velocity and pressure. If the smoke-control or HVAC sequence keeps a fan operating during closure, select a dynamic damper with ratings at least equal to actual airflow and static pressure. Do not assume every damper is dynamic simply because it has a spring.
Fire-damper actuation follows the listing and § 607.3.3. Fusible links commonly operate near 165°F, but the required operating temperature is tied to normal duct temperature and the code/listing criteria. Smoke dampers may actuate from duct or area detection or an engineered smoke-control command as the code permits. Their leakage class and elevated-temperature rating must match the design.
Installation follows the damper listing and manufacturer instructions, including sleeve, retaining-angle or breakaway-connection details, orientation, clearances, and actuator access. Field-added screws, insulation, or sealant must not block blade travel or violate the tested assembly.
4. Access and Identification
2018 IMC § 607.4 requires an approved means of access that is large enough to permit inspection and maintenance of the damper and its operating parts. The access must not reduce the fire-resistance rating, and a duct access door must be tight-fitting and suitable for the duct construction.
The 2018 edition does not specify a universal 12-by-12-inch opening. Later editions added more prescriptive language for certain dampers, but the Maryland Master reference is the 2018 IMC. For the exam, use the edition in the PSI bulletin.
Access points are permanently identified on the exterior with letters at least 0.5 inch high reading FIRE DAMPER, SMOKE DAMPER, or FIRE/SMOKE DAMPER as applicable, with the identification required by that edition. Access should be reachable without dismantling permanent construction and should allow the technician to see blades, link or actuator, and moving parts.
5. Inspection and Functional Testing
An inspection should verify:
The damper location, type, listing, and rating match the rated assembly and system sequence.
The opening and sleeve remain intact and free of unauthorized penetrations.
The access panel is identified and usable.
Blades, tracks, link, actuator, and switches are clean and unobstructed.
The damper closes fully and reopens or resets as designed.
Position indication and fire-alarm or smoke-control interlocks operate correctly.
Inspection frequency comes from the adopted fire code, referenced NFPA standard, damper listing, and facility program. Do not attribute a universal four- or six-year inspection interval directly to IMC § 607.4.