Study guide

7.2 Temperature Glide, Fractionation & Blends

Maryland HVAC Contractor License Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Maryland HVACR Licensing Framework & Board Jurisprudence

1.1 Maryland HVACR Board Authority, Scope & Statutory Framework 1.2 License Classifications, Scopes & Experience Prerequisites 1.3 Mandatory Insurance, Advertising & Business Regulations 1.4 Examination Logistics, Reciprocity & Board Disciplinary Actions

2 Chapter 2: Electrical Fundamentals, Circuits & Schematics

2.1 Electrical Principles, Ohm's Law & Power Calculations 2.2 Low-Voltage Control Circuits & Transformers 2.3 Electrical Schematics, Ladder Diagrams & Wiring Symbols 2.4 Electrical Test Instruments, Troubleshooting & Diagnostics

3 Chapter 3: Electric Motors & HVACR Control Devices

3.1 Electric Motor Types & Operating Characteristics 3.2 Motor Starting Components & Capacitors 3.3 Operational Controls, Contactors, Relays & Safety Limits

4 Chapter 4: Piping Systems, Materials & Code Installation Standards

4.1 Piping Materials, Sizing & Code Specifications 4.2 Joining Methods, Soldering, Brazing & Mechanical Fittings 4.3 Pipe Hangers, Supports & Vibration Isolation 4.4 Valves, Flow Controls & Piping Insulation

5 Chapter 5: Piping Testing, Hydronic Loop Design & Commissioning

5.1 Pressure Testing, Leak Detection & Code Inspection 5.2 Hydronic Piping Arrangements & Flow Dynamics 5.3 Hydronic Loop Accessories & Expansion Tanks

6 Chapter 6: Thermodynamics, Psychrometrics & The Refrigeration Cycle

6.1 Fundamentals of Heat Transfer & Thermodynamics 6.2 The Vapor-Compression Refrigeration Cycle 6.3 Psychrometric Principles & Chart Analysis 6.4 Psychrometric Diagnostic Applications

7 Chapter 7: Refrigerants, Environmental Regulations & EPA Section 608

7.1 Refrigerant Classifications, Chemistry & ASHRAE Safety Designations 7.2 Temperature Glide, Fractionation & Blends 7.3 Refrigerant Lubricants & Oil Management 7.4 EPA Section 608 Compliance & Recovery Standards

8 Chapter 8: Air Conditioning & Heat Pump Systems

8.1 ACCA Manual J Load Calculations & Manual S Equipment Sizing 8.2 Major System Components & Metering Devices 8.3 Heat Pump Operation, Reversing Valves & Defrost Cycles 8.4 AC & Heat Pump Installation, Charging & System Diagnostics

9 Chapter 9: Gas Heating Systems, Combustion Science & Venting

9.1 Combustion Science, Fuel Gas Properties & Burner Operation 9.2 Gas Furnace Components, Controls & Sequence of Operation 9.3 Gas Piping Sizing, Materials & Installation 9.4 Chimneys, Vents & Flue Gas Sizing

10 Chapter 10: Boilers, Hydronic Heating & Oil-Fired Systems

10.1 Low-Pressure Steam & Hydronic Boilers 10.2 Hydronic Heating Controls, Circulator Pumps & Zone Systems 10.3 Fuel Oil Burners, Storage & Supply Systems

11 Chapter 11: Air Distribution Systems, Duct Design & Ventilation

11.1 Air Distribution Fundamentals & ACCA Manual D 11.2 Duct Construction, Materials & SMACNA Standards 11.3 Duct Hangers, Supports, Insulation & Fire/Smoke Dampers 11.4 Commercial Exhaust, Kitchen Hoods & Building Ventilation

12 Chapter 12: Testing, Air Balancing & Construction Safety

12.1 Airflow Measurement, Testing & System Balancing (TAB) 12.2 Jobsite Safety, OSHA 1926 Standards & Fall Protection 12.3 Electrical Safety, PPE, Hazard Communication & SDS

7.2 Temperature Glide, Fractionation & Blends

Key Takeaways Explain This Topic AI

Azeotropic or near-azeotropic blends have little glide, while zeotropic blends change saturation temperature through evaporation and condensation.

For a zeotropic blend, bubble-point data represents saturated liquid and is used for subcooling; dew-point data represents saturated vapor and is used for superheat.

Fractionation can change blend composition, especially through vapor loss or incorrect charging, but the effect depends on the blend and leak conditions.

Follow the refrigerant manufacturer's cylinder-withdrawal instructions; zeotropic blends are generally withdrawn as liquid and safely metered for charging.

After a substantial blend loss, evaluate charge removal and replacement under manufacturer guidance instead of assuming every leak causes the same composition change.

Last updated: September 2026

7.2 Temperature Glide, Fractionation & Blends

Many modern refrigerants are multi-component blends formulated to replace phased-out CFCs and HCFCs. To properly charge, commission, and troubleshoot these systems, an HVAC contractor must understand the thermodynamic distinctions between pure compounds, azeotropic mixtures, and zeotropic blends, as well as the diagnostic implications of temperature glide and fractionation.

1. Pure Compounds, Azeotropes, and Zeotropes

Refrigerants are grouped into three primary thermodynamic categories based on how their molecular components behave during phase transitions:

A. Pure Compounds

Thermodynamic Behavior : Composed of a single chemical molecule (e.g., R-22, R-134a, R-32, R-12). At a given pressure, a pure compound boils and condenses at a single, unchanging saturation temperature.

Temperature Glide : Exactly 0.0 ∘ F 0.0^\circ\text{F} 0. 0 ∘ F .

Charging Protocol : Can be charged into a system from a supply cylinder as either a vapor or a liquid without altering the chemical composition.

B. Azeotropic Blends (500-Series)

Thermodynamic Behavior : A mixture of two or more refrigerants that forms a constant-boiling solution. At equilibrium, the liquid phase and vapor phase possess the exact same chemical formulation.

Representative Blends : R-500 (73.8% R-12 / 26.2% R-152a), R-502 (48.8% R-22 / 51.2% R-115), and R-507A (50% R-125 / 50% R-143a).

Temperature Glide : Negligible to zero ( 0.0 ∘ F 0.0^\circ\text{F} 0. 0 ∘ F ). Azeotropes condense and boil at a fixed temperature just like a pure compound.

Charging Protocol : Can be transferred as either liquid or vapor without risk of composition shift.

C. Zeotropic Blends (400-Series)

Thermodynamic Behavior : Blends composed of two or more refrigerants with different boiling points that maintain their individual phase-change behaviors. When heated at constant pressure, the constituent with the lowest boiling point (highest vapor pressure) vaporizes first, followed progressively by the higher-boiling constituents.

Near-Azeotropes : Zeotropic blends exhibiting very small temperature glide. For example, R-410A has a glide of less than 0.3 ∘ F 0.3^\circ\text{F} 0. 3 ∘ F ( 0.15 ∘ C 0.15^\circ\text{C} 0.1 5 ∘ C ) , and R-454B has a glide of approximately 1.5 ∘ F 1.5^\circ\text{F} 1. 5 ∘ F . In the field, these behave nearly like azeotropes in heat exchangers, but are chemically 400-series blends.

High-Glide Zeotropes : Blends exhibiting substantial temperature glide. For example, R-407C (23% R-32 / 25% R-125 / 52% R-134a) has a glide of 9 ∘ F 9^\circ\text{F} 9 ∘ F to 11 ∘ F 11^\circ\text{F} 1 1 ∘ F ( 5 ∘ C 5^\circ\text{C} 5 ∘ C to 6 ∘ C 6^\circ\text{C} 6 ∘ C ) across operating pressure ranges.

2. The Physics of Temperature Glide

Temperature glide is the observable temperature change that occurs during constant-pressure phase changes in zeotropic refrigerants:

Temperature Glide Definition: The numerical difference between the starting boiling temperature ( Bubble Point ) and the ending vaporization temperature ( Dew Point ) of a zeotropic blend at a constant pressure across an evaporator or condenser coil. Temperature Glide = T dew (vapor) − T bubble (liquid) \text{Temperature Glide} = T_{\text{dew (vapor)}} - T_{\text{bubble (liquid)}} Temperature Glide = T dew (vapor) ​ − T bubble (liquid) ​

Phase Progression Through System Heat Exchangers

In the Evaporator Coil : Saturated liquid enters the evaporator at the Bubble Point . As the refrigerant absorbs heat, the lower-boiling component (the "light end," e.g., R-32 in R-407C) evaporates first. As it travels through the coil tubing, the remaining liquid becomes increasingly rich in the higher-boiling component (the "heavy end," e.g., R-134a). Consequently, the boiling saturation temperature progressively climbs along the length of the coil from inlet to outlet, even if pressure remains constant.

In the Condenser Coil : Superheated discharge vapor enters the condenser and cools to the Dew Point , where the first liquid droplet condenses (rich in the higher-boiling component). As heat is rejected to outdoor air, the condensing saturation temperature progressively drops until the final vapor bubble condenses at the Bubble Point .

3. Bubble Point vs. Dew Point on P-T Cards

Standard Pressure-Temperature (P-T) charts for 400-series zeotropic blends list two distinct saturation temperature columns for every given pressure reading: the Bubble Point and the Dew Point .

Saturation Metric Physical State Represented Diagnostic Application Diagnostic Formula Error if Inverted

Bubble Point ( T bubble T_{\text{bubble}} T bubble ​ ) Saturated Liquid (first vapor bubbles appear) Subcooling calculation on liquid line Subcooling = T bubble − T line (liquid) \text{Subcooling} = T_{\text{bubble}} - T_{\text{line (liquid)}} Subcooling = T bubble ​ − T line (liquid) ​ Overstates subcooling by glide value (leads to severe undercharging)

Dew Point ( T dew T_{\text{dew}} T dew ​ ) Saturated Vapor (first liquid dew condenses) Superheat calculation on suction line Superheat = T line (suction) − T dew \text{Superheat} = T_{\text{line (suction)}} - T_{\text{dew}} Superheat = T line (suction) ​ − T dew ​ Understates superheat by glide value (risks compressor liquid slugging)

Field Diagnostic Protocol & Worked Example

A technician evaluates a commercial rooftop air conditioning system charged with R-407C :

Suction Line Measurements : Suction pressure = 65.0 psig 65.0\text{ psig} 65.0 psig . Suction line pipe temperature = 52.0 ∘ F 52.0^\circ\text{F} 52. 0 ∘ F .

Liquid Line Measurements : High-side liquid pressure = 240.0 psig 240.0\text{ psig} 240.0 psig . Liquid line pipe temperature = 98.0 ∘ F 98.0^\circ\text{F} 98. 0 ∘ F .

P-T Chart Reference for R-407C :

At 65.0 psig 65.0\text{ psig} 65.0 psig : Bubble Point = 29.5 ∘ F \text{Bubble Point} = 29.5^\circ\text{F} Bubble Point = 29. 5 ∘ F ; Dew Point = 40.0 ∘ F \text{Dew Point} = 40.0^\circ\text{F} Dew Point = 40. 0 ∘ F .

At 240.0 psig 240.0\text{ psig} 240.0 psig : Bubble Point = 110.0 ∘ F \text{Bubble Point} = 110.0^\circ\text{F} Bubble Point = 110. 0 ∘ F ; Dew Point = 121.0 ∘ F \text{Dew Point} = 121.0^\circ\text{F} Dew Point = 121. 0 ∘ F .

Calculations :

Evaporator Superheat : Always use the Dew Point ( 40.0 ∘ F 40.0^\circ\text{F} 40. 0 ∘ F ): Superheat = T suction line − T dew = 52.0 ∘ F − 40.0 ∘ F = 12.0 ∘ F \text{Superheat} = T_{\text{suction line}} - T_{\text{dew}} = 52.0^\circ\text{F} - 40.0^\circ\text{F} = 12.0^\circ\text{F} Superheat = T suction line ​ − T dew ​ = 52. 0 ∘ F − 40. 0 ∘ F = 12. 0 ∘ F (If the technician had mistakenly used the Bubble Point of 29.5 ∘ F 29.5^\circ\text{F} 29. 5 ∘ F , calculated superheat would appear to be an erroneous 22.5 ∘ F 22.5^\circ\text{F} 22. 5 ∘ F , leading them to misdiagnose a starving evaporator and overcharge the system).

Condenser Subcooling : Always use the Bubble Point ( 110.0 ∘ F 110.0^\circ\text{F} 110. 0 ∘ F ): Subcooling = T bubble − T liquid line = 110.0 ∘ F − 98.0 ∘ F = 12.0 ∘ F \text{Subcooling} = T_{\text{bubble}} - T_{\text{liquid line}} = 110.0^\circ\text{F} - 98.0^\circ\text{F} = 12.0^\circ\text{F} Subcooling = T bubble ​ − T liquid line ​ = 110. 0 ∘ F − 98. 0 ∘ F = 12. 0 ∘ F (If the technician had mistakenly used the Dew Point of 121.0 ∘ F 121.0^\circ\text{F} 121. 0 ∘ F , calculated subcooling would appear to be an erroneous 23.0 ∘ F 23.0^\circ\text{F} 23. 0 ∘ F , causing them to mistakenly remove refrigerant).

4. Fractionation Mechanics, System Leaks & Servicing Protocols

Fractionation is the physical separation of a zeotropic blend into its individual component parts due to differences in vapor pressure:

The Standing Vapor Leak Scenario

When an idle air conditioning system containing a high-glide zeotropic blend (such as R-407C) develops a slow pinhole leak in a vapor line or coil, the component with the highest vapor pressure (the lighter constituent, such as R-32) boils off and escapes at a faster rate than the less volatile constituent (such as R-134a).

Thermodynamic Consequences : The refrigerant remaining inside the system becomes "fractionated"—disproportionately rich in heavy, lower-pressure components. This changes the chemical formulation, alters compression ratios, elevates compressor discharge temperatures, reduces cooling capacity by 15% to 20% , and renders the manufacturer's published P-T charts invalid.

Servicing Protocols: Low-Glide vs. High-Glide Blends

Near-Azeotropes / Low-Glide Blends (R-410A, R-454B, R-404A) : Because temperature glide is minimal ( < 0.3 ∘ F < 0.3^\circ\text{F} < 0. 3 ∘ F to 1.5 ∘ F 1.5^\circ\text{F} 1. 5 ∘ F ), the composition change during a leak is negligible (less than 1% to 2%). Industry standards and EPA guidelines permit repairing the leak and topping off the remaining charge with fresh liquid refrigerant.

High-Glide Zeotropes (R-407C, R-401A, R-402A) : If a system loses more than 20% to 30% of its charge from a vapor leak while idle , the remaining charge has suffered severe fractionation. The contractor must recover the entire remaining altered charge, repair the leak, evacuate the system to 500 microns , and recharge with fresh virgin refrigerant weighed in as a liquid to the manufacturer's nameplate specification.

5. The Liquid Charging Mandate for 400-Series Blends

Inside any refrigerant supply cylinder containing a 400-series zeotropic blend, the vapor space above the liquid is fractionated: it contains a higher concentration of the low-boiling components than the liquid sitting at the bottom. ZEOTROPIC REFRIGERANT CYLINDER PHENOMENON

  • ┌──────────────────────────────────────────────────┐
  • │ VAPOR HEADSPACE: Fractionated! │
  • │ (Enriched in high-volatility 'light ends') │
  • ├~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~┤
  • │ LIQUID PHASE: Correct Chemical Blend Ratio! │
  • │ (Must be charged strictly from this layer) │
  • └──────────────────────────────────────────────────┘
  • Mandatory Liquid Withdrawal

Follow the cylinder and refrigerant manufacturer's instructions. Zeotropic blends are generally withdrawn as liquid to preserve composition, then introduced in a manner that prevents liquid damage to a running compressor; series number alone is not a complete safe-charging instruction.

Protecting the Compressor During Liquid Charging

Compressors are positive displacement vapor pumps; drawing liquid refrigerant directly into the suction service port causes hydraulic shock ("liquid slugging"), broken reed valves, and shattered scroll wraps. To charge liquid safely into the low-pressure side while the system is running:

Invert cylinders without internal dip tubes (or connect to the dedicated "Liquid" valve on dip-tube cylinders).

Install a liquid throttle restrictor valve or use the manifold gauge hand valve to meter the liquid through an orifice.

The restricted orifice creates a rapid pressure drop that flashes the liquid into vapor before it passes through the service valve into the compressor suction port.

Loading diagram... Phase Transitions and Temperature Glide in Zeotropic Refrigerants