Study guide
6.4 Psychrometric Diagnostic Applications
Maryland HVAC Contractor License Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Maryland HVACR Licensing Framework & Board Jurisprudence
1.1 Maryland HVACR Board Authority, Scope & Statutory Framework 1.2 License Classifications, Scopes & Experience Prerequisites 1.3 Mandatory Insurance, Advertising & Business Regulations 1.4 Examination Logistics, Reciprocity & Board Disciplinary Actions
2 Chapter 2: Electrical Fundamentals, Circuits & Schematics
2.1 Electrical Principles, Ohm's Law & Power Calculations 2.2 Low-Voltage Control Circuits & Transformers 2.3 Electrical Schematics, Ladder Diagrams & Wiring Symbols 2.4 Electrical Test Instruments, Troubleshooting & Diagnostics
3 Chapter 3: Electric Motors & HVACR Control Devices
3.1 Electric Motor Types & Operating Characteristics 3.2 Motor Starting Components & Capacitors 3.3 Operational Controls, Contactors, Relays & Safety Limits
4 Chapter 4: Piping Systems, Materials & Code Installation Standards
4.1 Piping Materials, Sizing & Code Specifications 4.2 Joining Methods, Soldering, Brazing & Mechanical Fittings 4.3 Pipe Hangers, Supports & Vibration Isolation 4.4 Valves, Flow Controls & Piping Insulation
5 Chapter 5: Piping Testing, Hydronic Loop Design & Commissioning
5.1 Pressure Testing, Leak Detection & Code Inspection 5.2 Hydronic Piping Arrangements & Flow Dynamics 5.3 Hydronic Loop Accessories & Expansion Tanks
6 Chapter 6: Thermodynamics, Psychrometrics & The Refrigeration Cycle
6.1 Fundamentals of Heat Transfer & Thermodynamics 6.2 The Vapor-Compression Refrigeration Cycle 6.3 Psychrometric Principles & Chart Analysis 6.4 Psychrometric Diagnostic Applications
7 Chapter 7: Refrigerants, Environmental Regulations & EPA Section 608
7.1 Refrigerant Classifications, Chemistry & ASHRAE Safety Designations 7.2 Temperature Glide, Fractionation & Blends 7.3 Refrigerant Lubricants & Oil Management 7.4 EPA Section 608 Compliance & Recovery Standards
8 Chapter 8: Air Conditioning & Heat Pump Systems
8.1 ACCA Manual J Load Calculations & Manual S Equipment Sizing 8.2 Major System Components & Metering Devices 8.3 Heat Pump Operation, Reversing Valves & Defrost Cycles 8.4 AC & Heat Pump Installation, Charging & System Diagnostics
9 Chapter 9: Gas Heating Systems, Combustion Science & Venting
9.1 Combustion Science, Fuel Gas Properties & Burner Operation 9.2 Gas Furnace Components, Controls & Sequence of Operation 9.3 Gas Piping Sizing, Materials & Installation 9.4 Chimneys, Vents & Flue Gas Sizing
10 Chapter 10: Boilers, Hydronic Heating & Oil-Fired Systems
10.1 Low-Pressure Steam & Hydronic Boilers 10.2 Hydronic Heating Controls, Circulator Pumps & Zone Systems 10.3 Fuel Oil Burners, Storage & Supply Systems
11 Chapter 11: Air Distribution Systems, Duct Design & Ventilation
11.1 Air Distribution Fundamentals & ACCA Manual D 11.2 Duct Construction, Materials & SMACNA Standards 11.3 Duct Hangers, Supports, Insulation & Fire/Smoke Dampers 11.4 Commercial Exhaust, Kitchen Hoods & Building Ventilation
12 Chapter 12: Testing, Air Balancing & Construction Safety
12.1 Airflow Measurement, Testing & System Balancing (TAB) 12.2 Jobsite Safety, OSHA 1926 Standards & Fall Protection 12.3 Electrical Safety, PPE, Hazard Communication & SDS
6.4 Psychrometric Diagnostic Applications
Key Takeaways Explain This Topic AI
Airflow and system capacities are governed by the three fundamental HVAC air equations: Sensible heat (Qs = 1.08 × CFM × ΔT), Latent heat (Ql = 0.68 × CFM × ΔW), and Total heat (Qt = 4.5 × CFM × Δh).
The constant 1.08 derives directly from standard air density (0.075 lb/ft³), specific heat (0.24 BTU/lb·°F), and conversion time (60 min/hr): 0.075 × 0.24 × 60 = 1.08.
Supply air CFM can be accurately verified in the field using electric auxiliary heat temperature rise: CFM = (Volts × Amps × 3.412) / (1.08 × ΔT).
The Apparatus Dew Point (ADP) represents the effective surface temperature of a cooling coil; Coil Bypass Factor (BF) measures the fraction of air that passes through the coil fins without contacting them (CF = 1 - BF).
Mixed air temperatures and enthalpy for economizers and ventilation are calculated using mass-weighted ratios: T_mixed = (T_RA × %RA) + (T_OA × %OA).
Last updated: September 2026
6.4 Psychrometric Diagnostic Applications
Mastering psychrometric diagnostic equations enables HVAC contractors to scientifically verify system airflow, evaluate heating and cooling capacities, diagnose coil bypass performance, and calculate mixed air conditions for ventilation and economizer systems. Rather than relying on guesswork, technicians utilize quantitative psychrometric formulas to identify duct restrictions, incorrect blower speeds, or defective coil operation.
1. The Three Foundational Airflow Diagnostic Equations
Three governing equations define heat transfer across forced-air coils based on volumetric airflow measured in Cubic Feet per Minute (CFM) under standard atmospheric air conditions ( ρ = 0.075 lb/ft 3 \rho = 0.075\text{ lb/ft}^3 ρ = 0.075 lb/ft 3 , c p = 0.24 BTU/lb ⋅ ∘ F c_p = 0.24\text{ BTU/lb}\cdot^\circ\text{F} c p = 0.24 BTU/lb ⋅ ∘ F ):
A. The Sensible Heat Equation Q s = 1.08 × CFM × Δ T Q_s = 1.08 \times \text{CFM} \times \Delta T Q s = 1.08 × CFM × Δ T
Derivation of the 1.08 Constant :
Mass flow rate of air ( m ˙ \dot{m} m ˙ ) equals volumetric airflow ( CFM \text{CFM} CFM ) converted to hours ( 60 min/hr 60\text{ min/hr} 60 min/hr ) and multiplied by standard density ( ρ \rho ρ ): m ˙ = CFM × 60 min/hr × 0.075 lb/ft 3 = 4.5 × CFM ( lbs of air/hr ) \dot{m} = \text{CFM} \times 60\text{ min/hr} \times 0.075\text{ lb/ft}^3 = 4.5 \times \text{CFM} \quad (\text{lbs of air/hr}) m ˙ = CFM × 60 min/hr × 0.075 lb/ft 3 = 4.5 × CFM ( lbs of air/hr ) Multiplying mass flow rate by the specific heat of dry air ( c p = 0.24 BTU / [ lb ⋅ ∘ F ] c_p = 0.24\text{ BTU}/[\text{lb}\cdot^\circ\text{F}] c p = 0.24 BTU / [ lb ⋅ ∘ F ] ) yields: Constant = 60 × 0.075 × 0.24 = 1.08 BTU / ( hr ⋅ CFM ⋅ ∘ F ) \text{Constant} = 60 \times 0.075 \times 0.24 = 1.08\text{ BTU}/(\text{hr}\cdot\text{CFM}\cdot^\circ\text{F}) Constant = 60 × 0.075 × 0.24 = 1.08 BTU / ( hr ⋅ CFM ⋅ ∘ F )
Rearranged for Airflow : CFM = Q s 1.08 × Δ T \text{CFM} = \frac{Q_s}{1.08 \times \Delta T} CFM = 1.08 × Δ T Q s Where Q s Q_s Q s is sensible heat capacity in BTU/hr \text{BTU/hr} BTU/hr and Δ T \Delta T Δ T is dry-bulb temperature change across the equipment (°F).
B. The Latent Heat Equation Q l = 0.68 × CFM × Δ W Q_l = 0.68 \times \text{CFM} \times \Delta W Q l = 0.68 × CFM × Δ W
Derivation of the 0.68 Constant :
Latent moisture change ( Δ W \Delta W Δ W ) is measured in grains of water per pound of dry air. The average latent heat of vaporization for water at typical room conditions is approximately 1 , 061 BTU/lb 1,061\text{ BTU/lb} 1 , 061 BTU/lb . Converting grains to pounds ( 7 , 000 grains = 1 lb 7,000\text{ grains} = 1\text{ lb} 7 , 000 grains = 1 lb ): Constant = 60 min/hr × 0.075 lb/ft 3 × 1 , 061 BTU/lb 7 , 000 grains/lb = 4 , 774.5 7 , 000 ≈ 0.682 ≈ 0.68 \text{Constant} = \frac{60\text{ min/hr} \times 0.075\text{ lb/ft}^3 \times 1,061\text{ BTU/lb}}{7,000\text{ grains/lb}} = \frac{4,774.5}{7,000} \approx 0.682 \approx 0.68 Constant = 7 , 000 grains/lb 60 min/hr × 0.075 lb/ft 3 × 1 , 061 BTU/lb = 7 , 000 4 , 774.5 ≈ 0.682 ≈ 0.68
Field Usage : Quantifies the rate of moisture extraction across an active cooling coil.
C. The Total Heat (Enthalpy) Equation Q t = 4.5 × CFM × Δ h Q_t = 4.5 \times \text{CFM} \times \Delta h Q t = 4.5 × CFM × Δ h
Derivation of the 4.5 Constant :
Air enthalpy ( h h h ) directly captures both sensible and latent thermal energy in BTU/lb \text{BTU/lb} BTU/lb . The constant represents standard air density multiplied by time conversion: Constant = 60 min/hr × 0.075 lb/ft 3 = 4.5 lb ⋅ min / ( ft 3 ⋅ hr ) \text{Constant} = 60\text{ min/hr} \times 0.075\text{ lb/ft}^3 = 4.5\text{ lb}\cdot\text{min}/(\text{ft}^3\cdot\text{hr}) Constant = 60 min/hr × 0.075 lb/ft 3 = 4.5 lb ⋅ min / ( ft 3 ⋅ hr )
Field Usage : Evaluates true total delivered capacity of an operating air conditioner or heat pump in the field using entering and leaving wet-bulb temperatures converted to enthalpy.
Equation Name Primary Formula Constant Derivation Required Field Measurements
Sensible Heat Q s = 1.08 × CFM × Δ T Q_s = 1.08 \times \text{CFM} \times \Delta T Q s = 1.08 × CFM × Δ T 60 × 0.075 × 0.24 = 1.08 60 \times 0.075 \times 0.24 = 1.08 60 × 0.075 × 0.24 = 1.08 Supply/Return Dry-Bulb Temperatures
Latent Heat Q l = 0.68 × CFM × Δ W Q_l = 0.68 \times \text{CFM} \times \Delta W Q l = 0.68 × CFM × Δ W ( 60 × 0.075 × 1 , 061 ) / 7 , 000 = 0.68 (60 \times 0.075 \times 1,061) / 7,000 = 0.68 ( 60 × 0.075 × 1 , 061 ) /7 , 000 = 0.68 Supply/Return Grains of Moisture ( W W W )
Total Heat Q t = 4.5 × CFM × Δ h Q_t = 4.5 \times \text{CFM} \times \Delta h Q t = 4.5 × CFM × Δ h 60 × 0.075 = 4.5 60 \times 0.075 = 4.5 60 × 0.075 = 4.5 Supply/Return Enthalpy ( h h h from WB)
2. Airflow Verification via Electric Heat Temperature Rise
Measuring airflow in installed duct systems using anemometers or pitot tube traverses can be distorted by turbulence, elbows, and damper transitions. The electric heat temperature rise method provides the most reliable field airflow measurement because electric resistance heat operates at 100% thermal efficiency ( P F = 1.0 PF = 1.0 PF = 1.0 ).
Field Testing Protocol
Disable the outdoor heat pump or condenser to ensure only electric resistance heat strips operate.
Measure operating voltage ( V V V ) across the electric heat elements using a calibrated true-RMS multimeter.
Measure operating amperage ( I I I ) on each ungrounded heating conductor using a clamp ammeter.
Calculate total electrical power input: Watts = V × I ( Single-Phase ) \text{Watts} = V \times I \quad (\text{Single-Phase}) Watts = V × I ( Single-Phase )
Convert Watts to thermal heat output ( 1 Watt = 3.41214 BTU/hr 1\text{ Watt} = 3.41214\text{ BTU/hr} 1 Watt = 3.41214 BTU/hr ): Q s = Watts × 3.41214 Q_s = \text{Watts} \times 3.41214 Q s = Watts × 3.41214
Measure the dry-bulb temperature of the entering return air ( T return T_{\text{return}} T return ) and leaving supply air ( T supply T_{\text{supply}} T supply ). Ensure the supply temperature probe is placed out of line-of-sight of radiant element glow (around an elbow or shielded) to avoid radiant heating errors: Δ T = T supply − T return \Delta T = T_{\text{supply}} - T_{\text{return}} Δ T = T supply − T return
Calculate true system airflow: CFM = Watts × 3.41214 1.08 × Δ T \text{CFM} = \frac{\text{Watts} \times 3.41214}{1.08 \times \Delta T} CFM = 1.08 × Δ T Watts × 3.41214
Worked Example: Heat Pump Airflow Diagnostic
A technician inspects a 3-ton residential heat pump in Baltimore, MD. The electric backup heat package draws 42.0 A 42.0\text{ A} 42.0 A at 240 V 240\text{ V} 240 V . Entering return air is 69.0 ∘ F 69.0^\circ\text{F} 69. 0 ∘ F and leaving supply air is 95.5 ∘ F 95.5^\circ\text{F} 95. 5 ∘ F :
Power: Watts = 240 V × 42.0 A = 10 , 080 W = 10.08 kW \text{Watts} = 240\text{ V} \times 42.0\text{ A} = 10,080\text{ W} = 10.08\text{ kW} Watts = 240 V × 42.0 A = 10 , 080 W = 10.08 kW .
Heat Output: Q s = 10 , 080 × 3.41214 = 34 , 394 BTU/hr Q_s = 10,080 \times 3.41214 = 34,394\text{ BTU/hr} Q s = 10 , 080 × 3.41214 = 34 , 394 BTU/hr .
Temperature Rise: Δ T = 95.5 − 69.0 = 26.5 ∘ F \Delta T = 95.5 - 69.0 = 26.5^\circ\text{F} Δ T = 95.5 − 69.0 = 26. 5 ∘ F .
Calculated Airflow: CFM = 34 , 394 1.08 × 26.5 = 34 , 394 28.62 = 1 , 201.7 CFM ≈ 1 , 202 CFM \text{CFM} = \frac{34,394}{1.08 \times 26.5} = \frac{34,394}{28.62} = 1,201.7\text{ CFM} \approx 1,202\text{ CFM} CFM = 1.08 × 26.5 34 , 394 = 28.62 34 , 394 = 1 , 201.7 CFM ≈ 1 , 202 CFM
Evaluation: For a 3-ton system, 1 , 202 CFM / 3.0 tons = 400.7 CFM/ton 1,202\text{ CFM} / 3.0\text{ tons} = 400.7\text{ CFM/ton} 1 , 202 CFM /3.0 tons = 400.7 CFM/ton , confirming ideal airflow tuning.
3. Coil Bypass Factor (BF) & Apparatus Dew Point (ADP)
When air passes through a finned-tube evaporator coil, not all air molecules make direct physical contact with the cold fin surfaces:
Apparatus Dew Point (ADP) : The effective surface temperature of the cooling coil tubes and fins. On the psychrometric chart, extending the coil process line to intersect the 100% saturation curve identifies the ADP.
Contact Factor ( C F CF CF ) : The fraction of total airstream volume that makes intimate contact with coil surfaces, cooling completely to the ADP.
Bypass Factor ( B F BF BF ) : The fraction of total airstream volume that passes between the fin spacings without contacting metal surfaces, exiting at entering air conditions: C F + B F = 1.0 ⟹ C F = 1 − B F CF + BF = 1.0 \implies CF = 1 - BF CF + BF = 1.0 ⟹ CF = 1 − BF
Bypass Factor Formula : B F = T leaving DB − T ADP T entering DB − T ADP BF = \frac{T_{\text{leaving DB}} - T_{\text{ADP}}}{T_{\text{entering DB}} - T_{\text{ADP}}} BF = T entering DB − T ADP T leaving DB − T ADP
Clinical Field Implications
Commercial 6- to 8-row deep cooling coils feature a low bypass factor ( B F = 0.02 − 0.05 BF = 0.02 - 0.05 BF = 0.02 − 0.05 ), maximizing dehumidification.
Residential 3- to 4-row coils typically exhibit B F = 0.08 − 0.15 BF = 0.08 - 0.15 BF = 0.08 − 0.15 .
A high bypass factor ( B F > 0.20 BF > 0.20 BF > 0.20 ) caused by missing coil block-off baffles, low fin density (< 10 FPI), or excessive face velocity (> 550 FPM) allows excessive unconditioned air to leak past the coil, resulting in high indoor humidity and elevated leaving air temperatures.
4. Mixed Air Calculations for Ventilation & Economizers
In commercial HVAC and rooftop unit (RTU) applications, outdoor ventilation air (OA) mixes with recirculated building return air (RA) in a mixing plenum upstream of the cooling and heating coils.
Mixed Air Dry-Bulb Temperature Formula T mixed = ( T RA × % RA ) + ( T OA × % OA ) T_{\text{mixed}} = (T_{\text{RA}} \times \%\text{RA}) + (T_{\text{OA}} \times \%\text{OA}) T mixed = ( T RA × % RA ) + ( T OA × % OA )
Where % R A + % O A = 1.0 \%RA + \%OA = 1.0 % R A + % O A = 1.0 (or 100 % 100\% 100% ). Expressed alternatively by airflow: T mixed = ( CFM RA × T RA ) + ( CFM OA × T OA ) CFM total T_{\text{mixed}} = \frac{(\text{CFM}_{\text{RA}} \times T_{\text{RA}}) + (\text{CFM}_{\text{OA}} \times T_{\text{OA}})}{\text{CFM}_{\text{total}}} T mixed = CFM total ( CFM RA × T RA ) + ( CFM OA × T OA )
Calculating Outdoor Air Percentage from Temperature Data
Technicians can determine the exact ventilation percentage delivered by economizer dampers without flow hoods by measuring dry-bulb temperatures: % OA = T mixed − T RA T OA − T RA × 100 % \%\text{OA} = \frac{T_{\text{mixed}} - T_{\text{RA}}}{T_{\text{OA}} - T_{\text{RA}}} \times 100\% % OA = T OA − T RA T mixed − T RA × 100%
Worked Diagnostic Scenario: Verifying Economizer Minimum Position
A commercial rooftop unit in Rockville, MD supplies 5 , 000 CFM 5,000\text{ CFM} 5 , 000 CFM of total airflow. Code requires a minimum 15% outdoor air ventilation rate ( 750 CFM 750\text{ CFM} 750 CFM ).
- Measured Return Air ( T RA T_{\text{RA}} T RA ): 72.0 ∘ F 72.0^\circ\text{F} 72. 0 ∘ F
- Measured Outdoor Air ( T OA T_{\text{OA}} T OA ): 92.0 ∘ F 92.0^\circ\text{F} 92. 0 ∘ F
- Measured Mixed Air ( T mixed T_{\text{mixed}} T mixed ): 76.0 ∘ F 76.0^\circ\text{F} 76. 0 ∘ F
Diagnostic Calculation : % OA = 76.0 − 72.0 92.0 − 72.0 = 4.0 20.0 = 0.20 = 20 % \%\text{OA} = \frac{76.0 - 72.0}{92.0 - 72.0} = \frac{4.0}{20.0} = 0.20 = 20\% % OA = 92.0 − 72.0 76.0 − 72.0 = 20.0 4.0 = 0.20 = 20%
Delivered Ventilation Airflow: 5 , 000 CFM × 0.20 = 1 , 000 CFM 5,000\text{ CFM} \times 0.20 = 1,000\text{ CFM} 5 , 000 CFM × 0.20 = 1 , 000 CFM .
Conclusion: The unit provides 20% outdoor air ( 1 , 000 CFM 1,000\text{ CFM} 1 , 000 CFM ), satisfying the mandatory code minimum ventilation rate of 15% ( 750 CFM 750\text{ CFM} 750 CFM ).