Study guide

8.1 Backflow Prevention & Cross-Connection Control

Maryland Journeyman Plumber Journey Plumber/Gas Fitter

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Maryland Licensing, Code Administration & the Exam

1.1 Maryland Plumbing Regulations & Licensing 1.2 The Journey Plumber/Gas Fitter Exam: Format, References & Open-Book Strategy

2 Chapter 2: Job-Site Safety & OSHA 29 CFR 1926

2.1 OSHA Construction Safety, PPE & Hazard Communication 2.2 Excavation & Trenching Safety (29 CFR 1926 Subpart P) 2.3 Confined Spaces, Ladders, Scaffolds & Hot Work

3 Chapter 3: Materials, Uses & Specifications

3.1 Approved Plumbing Materials, Pipes & Jointing 3.2 Hanger Spacing, Structural Protection & System Testing 3.3 Valves, Fittings, Fitting Selection & Prohibited Connections

4 Chapter 4: Sanitary Drainage & Waste Piping

4.1 Drainage Fixture Units (DFU) & Drain Pipe Sizing 4.2 Building Sewers, Cleanout Clearances & Underground Piping 4.3 Indirect & Special Waste Systems 4.4 Backwater Valves, Sump Pumps & Sewage Ejectors

5 Chapter 5: Venting Systems

5.1 Vent Sizing, Termination & Soil Stacks 5.2 Individual, Branch & Common Vents 5.3 Wet Venting & Circuit Venting 5.4 Air Admittance Valves (AAVs) & Special Venting

6 Chapter 6: Traps, Interceptors & Backwater Valves

6.1 Traps, Trap Seals & Trap Arm Requirements 6.2 Grease, Oil & Special-Waste Interceptors and Separators

7 Chapter 7: Water Supply & Distribution Systems

7.1 Water Supply Sizing & Fixture Unit (WSFU) Method 7.2 Water Heaters & Safety Devices 7.3 Pressure Regulation, Booster Systems & Disinfection 7.4 Water Service Piping, Meters, Valves & System Protection

8 Chapter 8: Backflow Prevention & Cross-Connection Control

8.1 Backflow Prevention & Cross-Connection Control 8.2 Air Gaps, Vacuum Breakers & Their Application Limits 8.3 Double Check & Reduced Pressure Principle (RPZ) Assemblies 8.4 Backflow Assembly Field Testing Procedures & Gauge Use 8.5 Maryland Backflow Program: 32-Hour Course, Certification & Reporting

9 Chapter 9: Fuel Gas Fundamentals, Materials & Pipe Sizing

9.1 Fuel Gas Properties, Heating Values & IFGC Scope 9.2 Fuel Gas Pipe Sizing & Materials 9.3 Approved Gas Piping Materials, CSST & Bonding 9.4 Gas Pipe Sizing Tables: Longest-Length & Branch-Length Methods 9.5 LP-Gas Systems, NFPA 58 & Propane-Specific Rules

10 Chapter 10: Gas Piping Installation, Testing & Purging

10.1 Gas Piping Installation, Testing & Purging 10.2 Gas Piping Support, Protection, Prohibited Locations & Concealed Piping 10.3 Shutoff Valves, Drips, Unions, Sediment Traps & Appliance Connectors 10.4 Gas Meters, Regulators, Pressure Levels & Overpressure Protection 10.5 Gas Leak Detection, Odorization & Emergency Response

11 Chapter 11: Gas Appliance Venting & Combustion Air

11.1 Gas Appliance Venting & Combustion Air 11.2 Appliance Categories I-IV, Vent Materials & Vent Connectors 11.3 Chimney & Vent Sizing Tables (Type B, Masonry & Common Venting) 11.4 Vent Termination, Clearances & Direct-Vent Systems 11.5 Combustion Air: Indoor & Outdoor Methods and Opening Sizing

12 Chapter 12: Gas Appliance Installation & Service

12.1 Gas Water Heaters, Furnaces & Boilers: Installation Rules 12.2 Appliance Clearances to Combustibles, Access & Location Limits 12.3 Gas Appliance Troubleshooting, Combustion Analysis & CO Safety

13 Chapter 13: Plumbing Fixtures, Fittings & Appliances

13.1 Fixture Clearances, Accessibility & Installation 13.2 Water Conservation Standards & Flow Rates 13.3 Commercial & Specialty Fixture Requirements

14 Chapter 14: Plumbing Mathematics

14.1 Plumbing Math I: Areas, Volumes, Capacities & Water Weight 14.2 Plumbing Math II: Offsets, Travel, Grade & Pipe Layout 14.3 Plumbing Math III: Gas Math, Meter Readings, BTU & Pressure Conversions

8.1 Backflow Prevention & Cross-Connection Control

Key Takeaways Explain This Topic AI

Backflow occurs via backsiphonage (caused by negative gauge pressure in supply lines) or backpressure (downstream pressure exceeding supply main pressure).

Air gaps provide the highest protection level; IPC 2018 Table 608.16.1 requires 1 inch for effective openings up to 1/2 inch, 1-1/2 inches up to 3/4 inch and 2 inches up to 1 inch (1-1/2, 2-1/2 and 3 inches respectively close to a wall), and only openings larger than 1 inch use the two-times and three-times multipliers.

Reduced Pressure Principle (RPZ) assemblies protect against high-hazard contaminants under both backsiphonage and backpressure; IPC 608.15 requires only that access be provided per the manufacturer's instructions, and 608.15.2.1 requires the relief port to discharge to an approved indirect waste receptor or outdoors.

Double Check Valve Assemblies (DCVA) are restricted to low-hazard pollutants only, whereas Pressure Vacuum Breakers (PVB) protect high/low hazard backsiphonage but cannot withstand backpressure.

IPC 2018 Section 312.10.2 requires testable assemblies (RPZ, DCVA, PVB) to be tested at least annually, and Maryland certifies the testers who perform that work through the COMAR 09.20.04 cross-connection and backflow prevention training programme.

Last updated: July 2026

8.1 Backflow Prevention & Cross-Connection Control

Cross-connection control is the highest priority safety standard in modern plumbing. A cross-connection is any actual or potential physical connection between a potable water supply system and any source containing non-potable water, sewage, industrial chemicals, or contaminants. Under IPC Section 608 and Maryland State Plumbing Regulations (COMAR 09.20), plumbers are legally obligated to protect public health by installing, inspecting, and maintaining approved backflow prevention assemblies at every potential point of contamination.

1. Hydraulics of Backflow: Backsiphonage vs. Backpressure

Backflow is the unwanted reversal of flow of non-potable water or other liquids into the potable water distribution system. Backflow occurs through two distinct hydraulic mechanisms: backsiphonage and backpressure .

Backsiphonage

Backsiphonage is backflow caused by negative (sub-atmospheric or vacuum) pressure in the potable supply piping. It functions exactly like drinking through a straw: when supply pressure drops below atmospheric pressure ( 0 psig 0 \text{ psig} 0 psig or 14.7 psia 14.7 \text{ psia} 14.7 psia ), surrounding liquids are sucked into the potable water line.

Common Causes of Backsiphonage:

Municipal water main breaks or line repairs.

High volume water draw nearby during firefighting operations.

Undersized booster pumps drawing a severe vacuum on suction lines.

Draining a building supply line without opening high-point air vents.

Backpressure

Backpressure occurs when the pressure at a downstream fixture, appliance, or non-potable piping system exceeds the pressure supplying it from the potable water main.

Common Causes of Backpressure:

Booster pumps operating downstream without backflow protection.

High-pressure boiler feed systems or hydronic heating loops.

Thermal expansion of water in closed heating piping.

Overhead elevated storage tanks or high-rise vertical piping columns generating static head pressure ( 0.433 psi/ft 0.433 \text{ psi/ft} 0.433 psi/ft ).

2. Hazard Classifications: High Hazard vs. Low Hazard

IPC Section 608 categorizes cross-connections into two distinct risk levels to dictate the required level of backflow protection:

High Hazard (Contaminant): An impairment of the potable water quality that creates an actual hazard to public health through poisoning or the spread of disease. Examples include toxic chemicals, boiler water treated with rust inhibitors, industrial process fluids, sewage, mortuary sinks, and irrigation systems containing fertilizers/pesticides.

Low Hazard (Pollutant): An impairment of the potable water quality that affects the aesthetic qualities of water (taste, odor, color) but does not constitute a health hazard or toxic threat. Examples include food-grade dyes, stagnant water in fire sprinkler systems (without chemical additives), drinking fountain drains, and commercial ice makers.

3. Approved Backflow Prevention Assemblies & Devices

IPC Section 608 mandates specific backflow prevention assemblies based on hazard level, hydraulic mechanism (backsiphonage vs. backpressure), and continuous pressure status.

1. Air Gap (AG)

An Air Gap is an unobstructed vertical physical separation through the free atmosphere between the lowest opening of a supply pipe and the flood level rim of the receiving vessel.

Protection Rating: Protects against High Hazard and Low Hazard , under both Backsiphonage and Backpressure .

Sizing Rule (IPC Table 608.16.1): The table gives flat values for small outlets and multipliers only for large ones . An effective opening not greater than 1/2 inch requires 1 inch ( 1-1/2 inches close to a wall); not greater than 3/4 inch requires 1-1/2 inches ( 2-1/2 inches close to a wall); not greater than 1 inch requires 2 inches ( 3 inches close to a wall). Only for effective openings greater than 1 inch does the gap become two times the diameter of the effective opening, or three times where the outlet is close to a wall. Applying the 2x/3x multiplier to a small outlet under-sizes the gap: a 3/4-inch faucet close to a wall needs 2-1/2 inches, not the 2-1/4 inches a straight 3x produces.

2. Reduced Pressure Principle Backflow Assembly (RPZ / RP)

An RPZ assembly consists of two independently acting, spring-loaded check valves separated by a hydraulically operating, differential pressure relief valve located between them.

Operation: The relief valve maintains a minimum differential pressure of 2.0 psi between the supply zone and the intermediate chamber. If either check valve leaks or supply pressure drops, the relief valve opens to atmosphere and discharges water onto the floor, breaking the backflow path.

Protection Rating: Protects against High Hazard and Low Hazard , under both Backsiphonage and Backpressure .

Installation Rules: Must be installed horizontally (unless specifically certified for vertical orientation). Must be installed with access provided as specified by the manufacturer's instructions (IPC 608.15) - the IPC sets no numeric mounting-height range ; the familiar 12-inch minimum is a USC Manual recommendation and any upper limit comes from the individual water purveyor (commonly 30 to 36 inches). Must NEVER be installed in a pit, vault, or submerged location subject to flooding, because submerging the relief port causes catastrophic cross-connection!

3. Double Check Valve Assembly (DCVA / DC)

A DCVA consists of two independently acting, spring-loaded check valves enclosed within a single body, equipped with four test cocks and two tightly closing shutoff valves.

Protection Rating: Protects against Low Hazard ONLY under both Backsiphonage and Backpressure .

Installation Rules: Allowed in pits or vaults if properly drained. Does not discharge water to atmosphere during normal operation. Cannot be used where toxic contaminants exist (e.g. chemical boiler feeds).

4. Pressure Vacuum Breaker (PVB) & Spill-Resistant Vacuum Breaker (SVB)

A PVB assembly contains an independently operating spring-loaded check valve and an independently operating spring-loaded air inlet valve that opens whenever internal pressure drops to 1.0 psi above atmospheric.

Protection Rating: Protects against High Hazard and Low Hazard , for Backsiphonage ONLY .

Critical Limitation: Cannot protect against backpressure!

Installation Rules: Must be installed at least 12 inches above the highest downstream piping or overflow rim of all outlets served. Subject to continuous line pressure (24 hours/day).

5. Atmospheric Vacuum Breaker (AVB)

An AVB is a non-testable device containing a float check that drops under negative pressure to open an air vent to atmosphere.

Protection Rating: Protects against High Hazard and Low Hazard , for Backsiphonage ONLY .

Critical Limitations: Cannot be under continuous pressure for more than 12 hours in any 24-hour period . Must NEVER have any shutoff valves downstream of the device!

Installation Rules: Must be installed at least 6 inches above the highest downstream outlet or flood level rim .

4. Backflow Device Selection Matrix

Backflow Assembly / Device Hazard Level Protected Backsiphonage Protected? Backpressure Protected? Continuous Pressure Allowed? Min. Installation Height Testable Assembly?

  • Air Gap (AG) High & Low Yes Yes N/A Per Table 608.16.1 (1" min; 2x/3x only above a 1" opening) No (Visual)
  • Reduced Pressure Principle (RPZ) High & Low Yes Yes Yes Access per mfr. instructions (608.15) Yes (Annual)
  • Double Check Valve (DCVA) Low ONLY Yes Yes Yes Access per mfr. instructions (608.15) Yes (Annual)
  • Pressure Vacuum Breaker (PVB) High & Low Yes NO Yes 12" above highest outlet Yes (Annual)
  • Atmospheric Vacuum Breaker (AVB) High & Low Yes NO NO (<12 hrs) 6" above highest outlet No
  • 5. Maryland Annual Testing & Maintenance Mandates

Under Maryland law (COMAR 09.20) and local purveyor regulations (WSSC, Baltimore City, Anne Arundel DPW):

Initial Certification: All testable backflow assemblies (RPZ, DCVA, PVB, SVB) must be tested immediately upon installation, repair, or relocation.

Annual Recertification: Testable assemblies must be field-tested annually by a Maryland-Certified Backflow Technician using calibrated differential pressure gauge kits.

Record Keeping: Test reports detailing differential pressure readings (e.g. check valve #1 holding at ≥ 5.0 psid \ge 5.0 \text{ psid} ≥ 5.0 psid , relief valve opening at ≥ 2.0 psid \ge 2.0 \text{ psid} ≥ 2.0 psid ) must be submitted to the local water purveyor on that purveyor's own schedule - WSSC allows 30 business days, while Anne Arundel County requires 30 days for a passing test and 72 hours for a failure.

6. Exam Traps & Real-World Pitfalls

Exam Trap 1 (AVB Valves): Placing a shutoff valve or hose nozzle valve downstream of an Atmospheric Vacuum Breaker (AVB). This traps continuous pressure behind the AVB, causing the air disc to stick closed and rendering the device completely useless during backsiphonage.

Exam Trap 2 (Submerged RPZ): Installing an RPZ in a basement pit or sump pit. If the pit fills with water, the relief port becomes submerged. Under backsiphonage, dirty pit water will be sucked into the relief port directly into the municipal drinking supply!

Exam Trap 3 (DCVA on Chemical Boiler): Using a Double Check Valve Assembly on a commercial hydronic heating boiler treated with toxic chemical rust inhibitors (such as ethylene glycol or hydrazine). Because toxic chemicals are High Hazard, an RPZ or Air Gap is mandatory!

Exam Trap 4 (Hose Bibb Protection): Connecting a garden hose to an un-protected sillcock. IPC 608.16.4.2 mandates that sillcocks, hose bibbs, wall hydrants and other openings with a hose connection be protected by an atmospheric-type or pressure-type vacuum breaker, or a permanently attached hose connection vacuum breaker (ASSE 1011, typically secured with a non-removable breakaway set screw). Two exceptions apply: water heater and boiler drain valves provided with hose threads and intended only for draining the vessel, and clothes-washer supply valves where backflow protection is otherwise provided or is integral to the machine.

Loading diagram... Cross-Connection Hazard & Assembly Selection Tree