Study guide

4.4 Backwater Valves, Sump Pumps & Sewage Ejectors

Maryland Journeyman Plumber Journey Plumber/Gas Fitter

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Maryland Licensing, Code Administration & the Exam

1.1 Maryland Plumbing Regulations & Licensing 1.2 The Journey Plumber/Gas Fitter Exam: Format, References & Open-Book Strategy

2 Chapter 2: Job-Site Safety & OSHA 29 CFR 1926

2.1 OSHA Construction Safety, PPE & Hazard Communication 2.2 Excavation & Trenching Safety (29 CFR 1926 Subpart P) 2.3 Confined Spaces, Ladders, Scaffolds & Hot Work

3 Chapter 3: Materials, Uses & Specifications

3.1 Approved Plumbing Materials, Pipes & Jointing 3.2 Hanger Spacing, Structural Protection & System Testing 3.3 Valves, Fittings, Fitting Selection & Prohibited Connections

4 Chapter 4: Sanitary Drainage & Waste Piping

4.1 Drainage Fixture Units (DFU) & Drain Pipe Sizing 4.2 Building Sewers, Cleanout Clearances & Underground Piping 4.3 Indirect & Special Waste Systems 4.4 Backwater Valves, Sump Pumps & Sewage Ejectors

5 Chapter 5: Venting Systems

5.1 Vent Sizing, Termination & Soil Stacks 5.2 Individual, Branch & Common Vents 5.3 Wet Venting & Circuit Venting 5.4 Air Admittance Valves (AAVs) & Special Venting

6 Chapter 6: Traps, Interceptors & Backwater Valves

6.1 Traps, Trap Seals & Trap Arm Requirements 6.2 Grease, Oil & Special-Waste Interceptors and Separators

7 Chapter 7: Water Supply & Distribution Systems

7.1 Water Supply Sizing & Fixture Unit (WSFU) Method 7.2 Water Heaters & Safety Devices 7.3 Pressure Regulation, Booster Systems & Disinfection 7.4 Water Service Piping, Meters, Valves & System Protection

8 Chapter 8: Backflow Prevention & Cross-Connection Control

8.1 Backflow Prevention & Cross-Connection Control 8.2 Air Gaps, Vacuum Breakers & Their Application Limits 8.3 Double Check & Reduced Pressure Principle (RPZ) Assemblies 8.4 Backflow Assembly Field Testing Procedures & Gauge Use 8.5 Maryland Backflow Program: 32-Hour Course, Certification & Reporting

9 Chapter 9: Fuel Gas Fundamentals, Materials & Pipe Sizing

9.1 Fuel Gas Properties, Heating Values & IFGC Scope 9.2 Fuel Gas Pipe Sizing & Materials 9.3 Approved Gas Piping Materials, CSST & Bonding 9.4 Gas Pipe Sizing Tables: Longest-Length & Branch-Length Methods 9.5 LP-Gas Systems, NFPA 58 & Propane-Specific Rules

10 Chapter 10: Gas Piping Installation, Testing & Purging

10.1 Gas Piping Installation, Testing & Purging 10.2 Gas Piping Support, Protection, Prohibited Locations & Concealed Piping 10.3 Shutoff Valves, Drips, Unions, Sediment Traps & Appliance Connectors 10.4 Gas Meters, Regulators, Pressure Levels & Overpressure Protection 10.5 Gas Leak Detection, Odorization & Emergency Response

11 Chapter 11: Gas Appliance Venting & Combustion Air

11.1 Gas Appliance Venting & Combustion Air 11.2 Appliance Categories I-IV, Vent Materials & Vent Connectors 11.3 Chimney & Vent Sizing Tables (Type B, Masonry & Common Venting) 11.4 Vent Termination, Clearances & Direct-Vent Systems 11.5 Combustion Air: Indoor & Outdoor Methods and Opening Sizing

12 Chapter 12: Gas Appliance Installation & Service

12.1 Gas Water Heaters, Furnaces & Boilers: Installation Rules 12.2 Appliance Clearances to Combustibles, Access & Location Limits 12.3 Gas Appliance Troubleshooting, Combustion Analysis & CO Safety

13 Chapter 13: Plumbing Fixtures, Fittings & Appliances

13.1 Fixture Clearances, Accessibility & Installation 13.2 Water Conservation Standards & Flow Rates 13.3 Commercial & Specialty Fixture Requirements

14 Chapter 14: Plumbing Mathematics

14.1 Plumbing Math I: Areas, Volumes, Capacities & Water Weight 14.2 Plumbing Math II: Offsets, Travel, Grade & Pipe Layout 14.3 Plumbing Math III: Gas Math, Meter Readings, BTU & Pressure Conversions

4.4 Backwater Valves, Sump Pumps & Sewage Ejectors

Key Takeaways Explain This Topic AI

Backwater valves are required only on drainage branches serving fixtures installed on a floor whose finished floor elevation is below the elevation of the manhole cover of the next upstream manhole in the public sewer (IPC 714.1).

Sewage ejectors receiving water closet discharge must be capable of passing 2-inch spherical solids and require a minimum 2-inch discharge line and a gas-tight, vented pit.

Sump and ejector discharge piping MUST feature an accessible check valve and a full-port shutoff valve installed downstream of the check valve.

Ejector discharge lines must enter the top of the horizontal gravity building drain using a wye fitting, not less than 10 pipe diameters from the base of any soil stack, waste stack or fixture drain (IPC 712.3.5).

Last updated: July 2026

4.4 Backwater Valves, Sump Pumps & Sewage Ejectors

When plumbing fixtures are installed below the crown of the public sewer main or in basements vulnerable to municipal sewer surcharges, gravity drainage alone cannot guarantee safety. IPC Chapter 7 (Sections 712 and 714) establishes explicit installation mandates for backwater valves , clear-water sump pumps , and solids-handling sewage ejectors .

Backwater Valves: Surcharge Protection (IPC 714)

A backwater valve is a mechanical check valve installed in a drainage line to automatically prevent public sewer backflow from flooding low-lying structure levels during heavy rain events or sewer blockages.

Where Backwater Valves ARE Required

Backwater valves must be installed ONLY on drainage branches that receive discharge from fixtures installed on a floor with a finished floor elevation below the elevation of the manhole cover of the next upstream manhole in the public sewer on the public sewer main. [ Backwater Valve Installation Logic ]

  • Upstream Public Sewer Manhole Rim Elevation = 100.0 ft
  • =======================================================
  • Upper Floor Fixtures (Rim = 108.0 ft) ------> Gravity Drain (Bypasses Backwater Valve!)

Basement Fixtures (Rim = 96.0 ft) ----------> Must Flow Through BACKWATER VALVE!

Critical Exam Rule: Upper-floor fixtures whose flood level rims are ABOVE the manhole cover elevation MUST NOT discharge through the backwater valve. If upper-floor waste is routed through a closed backwater valve during a sewer backup, the upper-floor waste will back up and overflow out of the basement fixtures inside the building!

Mechanical Requirements

Accessibility: Backwater valves must be installed in an accessible location with a removable access cover panel or manhole chamber.

Flapper Design: Must feature a floating or swing flapper that provides full-bore flow in the normal direction of drainage and seals drop-tight against back-pressure.

Clear-Water Sump Pumps vs. Sewage Ejectors

Plumbing codes strictly segregate clear-water drainage (subsoil groundwater, AC condensate, storm run-off) from blackwater/sanitary wastewater (toilet, sink, and shower waste).

  • Feature Clear-Water Sump Pump Sewage Ejector Pump
  • Waste Type Groundwater, subsoil drains, condensate Human waste, sewage, fixture discharge
  • Sanitary Sewer Connection STRICTLY PROHIBITED MANDATORY
  • Solids Handling Must pass 1/2-inch spherical solids (IPC 712.4.2) Must pass 2-inch spherical solids

Minimum Discharge Pipe 1-1/4 inches 2 inches (Table 712.4.2 starts at 2 in / 21 gpm; grinder pumps 1-1/4 in, macerating toilets 3/4 in)

Pit Venting Gastight removable cover, vented per Chapter 9 Gastight removable cover, vented per Chapter 9 (size from Table 906.5.1)

  • Basin Minimum Size 18" diameter × 24" depth 18" diameter × 24" depth (Sized for inflow)
  • Sewage Ejector System Engineering (IPC 712)

When basement plumbing fixtures (water closets, showers, lavatories) are situated below the horizontal building drain elevation, a sewage ejector pump system is required to lift the wastewater up to the gravity drain.

Pump & Pit Specifications

Solids Handling Capacity: Any ejector pump receiving water closet discharge must be a solids-handling pump capable of passing 2-inch spherical solids without clogging.

Discharge Pipe Size: Minimum 2-inch diameter discharge line.

Gas-Tight Pit & Venting: The ejector pit must be water-tight and gas-tight, sealed with a gasketed lid. The basin must be vented to the outdoor atmosphere through a dedicated vent pipe (minimum 1-1/2 inch or 2 inch) to relieve air pressure during pump discharge and permit gravity inflow. The vent can connect to the stack vent or vent header.

Duplex Ejector Systems: In public or commercial occupancies where fixture operation cannot be interrupted, duplex ejector pumps (two pumps in a shared pit) with alternating controls and an audible high-water alarm are standard engineering practice and are often required by the AHJ - but note that IPC 2018 Chapter 7 contains no duplex-pump or high-water-alarm requirement , so do not cite it as a code answer.

Required Valve Sequence & Gravity Main Connection (IPC 712.2 & 712.3)

The connection of a sewage ejector discharge line into the gravity building drain requires a precise valve arrangement and fitting orientation to prevent backflow and mechanical stress.

Correct Discharge Valve Sequence

Moving outward from the pump discharge outlet along the discharge line, valves MUST be installed in this exact order: Ejector Pump ⟶ Check Valve ⟶ Full-Port Shutoff Valve (Gate or Ball Valve) ⟶ Gravity Drain \text{Ejector Pump} \longrightarrow \text{Check Valve} \longrightarrow \text{Full-Port Shutoff Valve (Gate or Ball Valve)} \longrightarrow \text{Gravity Drain} Ejector Pump ⟶ Check Valve ⟶ Full-Port Shutoff Valve (Gate or Ball Valve) ⟶ Gravity Drain

Check Valve: Installed first to prevent pumped liquid in the vertical discharge column from flowing back into the sump pit when the pump cycles off.

Full-Port Shutoff Valve: Installed downstream (on the gravity side) of the check valve. This allows technician servicing of the check valve or pump without draining the overhead discharge pipe.

Connection to Gravity Drain Line

Top Entry Fitting: The ejector discharge line must enter the horizontal building drain or branch from the TOP using a wye fitting or combination wye and 1/8 bend.

Downstream Distance: The pump discharge must connect to the drainage system not less than 10 pipe diameters from the base of any soil stack, waste stack or fixture drain (IPC 712.3.5 ) - pipe diameters, not feet to prevent hydraulic jumping and pneumatic pressure fluctuations. [ Gravity Drain Connection Detail ]

  • Full-Port Valve
  • |
  • Horizontal Gravity Drain <=== [ Top Wye Connection ] <=== Check Valve <=== Ejector Pump Discharge
  • Step-by-Step Ejector Capacity Calculation Example

Scenario: Calculate the required minimum discharge rate (in GPM) for a duplex sewage ejector serving a basement restroom with 2 flush tank water closets (3 DFU each), 2 lavatories (1 DFU each), and 1 shower (2 DFU).

  • Step 1: Determine Total Fixture Units
  • 2 Water closets × 3 DFU = 6 DFU
  • 2 Lavatories × 1 DFU = 2 DFU
  • 1 Shower × 2 DFU = 2 DFU
  • Total Load = 10 DFU
  • Step 2: Convert DFU to Peak GPM Inflow

There is no Table 712.2 (712.2 is "Valves required"). IPC 709.3 converts flow at 1 gpm = 2 dfu , so a 10 DFU load is about 5 gpm of design flow - but the governing number is the code minimum: Table 712.4.2 requires a pump serving a 2-inch discharge to deliver not less than 21 gpm .

To prevent solids settling and maintain self-cleansing velocity (min 2 ft/sec) in a 2-inch discharge line, the pump must discharge at a minimum flow rate of 21 GPM .

Therefore, the ejector pump must be selected to deliver at least 21 GPM against the Total Dynamic Head (TDH = static lift + friction loss).

Maryland Journeyman Exam Pitfalls

Prohibited Sump Connections: Connecting subsoil clear groundwater drains to a sewage ejector pit is a major violation (overloads sewage treatment plants).

Valve Order Distractor: Exam questions will try to trick you by placing the gate valve before the check valve. Remember: Pump → \rightarrow → Check Valve → \rightarrow → Gate Valve !

Unvented Sump Cover: Operating a sewage ejector with an unvented cover causes air locking, preventing fixtures from draining by gravity into the pit.

Loading diagram... Sewage Ejector Pump Installation & Top Gravity Main Connection