Study guide
9.1 Fuel Gas Properties, Heating Values & IFGC Scope
Maryland Journeyman Plumber Journey Plumber/Gas Fitter
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Maryland Licensing, Code Administration & the Exam
1.1 Maryland Plumbing Regulations & Licensing 1.2 The Journey Plumber/Gas Fitter Exam: Format, References & Open-Book Strategy
2 Chapter 2: Job-Site Safety & OSHA 29 CFR 1926
2.1 OSHA Construction Safety, PPE & Hazard Communication 2.2 Excavation & Trenching Safety (29 CFR 1926 Subpart P) 2.3 Confined Spaces, Ladders, Scaffolds & Hot Work
3 Chapter 3: Materials, Uses & Specifications
3.1 Approved Plumbing Materials, Pipes & Jointing 3.2 Hanger Spacing, Structural Protection & System Testing 3.3 Valves, Fittings, Fitting Selection & Prohibited Connections
4 Chapter 4: Sanitary Drainage & Waste Piping
4.1 Drainage Fixture Units (DFU) & Drain Pipe Sizing 4.2 Building Sewers, Cleanout Clearances & Underground Piping 4.3 Indirect & Special Waste Systems 4.4 Backwater Valves, Sump Pumps & Sewage Ejectors
5 Chapter 5: Venting Systems
5.1 Vent Sizing, Termination & Soil Stacks 5.2 Individual, Branch & Common Vents 5.3 Wet Venting & Circuit Venting 5.4 Air Admittance Valves (AAVs) & Special Venting
6 Chapter 6: Traps, Interceptors & Backwater Valves
6.1 Traps, Trap Seals & Trap Arm Requirements 6.2 Grease, Oil & Special-Waste Interceptors and Separators
7 Chapter 7: Water Supply & Distribution Systems
7.1 Water Supply Sizing & Fixture Unit (WSFU) Method 7.2 Water Heaters & Safety Devices 7.3 Pressure Regulation, Booster Systems & Disinfection 7.4 Water Service Piping, Meters, Valves & System Protection
8 Chapter 8: Backflow Prevention & Cross-Connection Control
8.1 Backflow Prevention & Cross-Connection Control 8.2 Air Gaps, Vacuum Breakers & Their Application Limits 8.3 Double Check & Reduced Pressure Principle (RPZ) Assemblies 8.4 Backflow Assembly Field Testing Procedures & Gauge Use 8.5 Maryland Backflow Program: 32-Hour Course, Certification & Reporting
9 Chapter 9: Fuel Gas Fundamentals, Materials & Pipe Sizing
9.1 Fuel Gas Properties, Heating Values & IFGC Scope 9.2 Fuel Gas Pipe Sizing & Materials 9.3 Approved Gas Piping Materials, CSST & Bonding 9.4 Gas Pipe Sizing Tables: Longest-Length & Branch-Length Methods 9.5 LP-Gas Systems, NFPA 58 & Propane-Specific Rules
10 Chapter 10: Gas Piping Installation, Testing & Purging
10.1 Gas Piping Installation, Testing & Purging 10.2 Gas Piping Support, Protection, Prohibited Locations & Concealed Piping 10.3 Shutoff Valves, Drips, Unions, Sediment Traps & Appliance Connectors 10.4 Gas Meters, Regulators, Pressure Levels & Overpressure Protection 10.5 Gas Leak Detection, Odorization & Emergency Response
11 Chapter 11: Gas Appliance Venting & Combustion Air
11.1 Gas Appliance Venting & Combustion Air 11.2 Appliance Categories I-IV, Vent Materials & Vent Connectors 11.3 Chimney & Vent Sizing Tables (Type B, Masonry & Common Venting) 11.4 Vent Termination, Clearances & Direct-Vent Systems 11.5 Combustion Air: Indoor & Outdoor Methods and Opening Sizing
12 Chapter 12: Gas Appliance Installation & Service
12.1 Gas Water Heaters, Furnaces & Boilers: Installation Rules 12.2 Appliance Clearances to Combustibles, Access & Location Limits 12.3 Gas Appliance Troubleshooting, Combustion Analysis & CO Safety
13 Chapter 13: Plumbing Fixtures, Fittings & Appliances
13.1 Fixture Clearances, Accessibility & Installation 13.2 Water Conservation Standards & Flow Rates 13.3 Commercial & Specialty Fixture Requirements
14 Chapter 14: Plumbing Mathematics
14.1 Plumbing Math I: Areas, Volumes, Capacities & Water Weight 14.2 Plumbing Math II: Offsets, Travel, Grade & Pipe Layout 14.3 Plumbing Math III: Gas Math, Meter Readings, BTU & Pressure Conversions
9.1 Fuel Gas Properties, Heating Values & IFGC Scope
Key Takeaways Explain This Topic AI
Natural gas has a specific gravity of about 0.60 and about 1,000 Btu per cubic foot; commercial propane is about 1.52 specific gravity, about 2,500 Btu per cubic foot of vapor and about 91,500 Btu per gallon of liquid.
One psi equals 27.7 inches of water column, so the typical 7 in. w.c. natural gas utilization pressure is about 0.25 psi and 11 in. w.c. propane is about 0.40 psi.
Methane's flammable range is about 5 to 15 percent in air and propane's is about 2.1 to 9.5 percent; 49 CFR 192.625(a) requires odorization detectable at one-fifth of the lower explosive limit.
Burning one cubic foot of natural gas needs about 10 cubic feet of air (9.53 stoichiometric); one cubic foot of propane needs about 24 cubic feet (23.8 stoichiometric).
IFGC 2018 Section 402.7 caps gas piping inside buildings at 5 psig unless one of seven listed conditions is met, and the IFGC does not apply above 125 psig natural gas or 20 psig LP-gas.
Last updated: July 2026
9.1 Fuel Gas Properties, Heating Values & IFGC Scope
Quick Answer: Natural gas has a specific gravity of about 0.60 and delivers roughly 1,000 Btu per cubic foot ; commercial propane has a specific gravity of about 1.52 and delivers roughly 2,500 Btu per cubic foot . Natural gas rises when it leaks, propane sinks, and the same appliance load draws about 2.5 times more cubic feet per hour on natural gas than on propane.
Gas Appliances and Piping is 40 of the 100 scored items on the Maryland Journey Plumber/Gas Fitter exam — more than drainage, venting, water supply and backflow combined. Everything in that domain rests on the properties below, and you will reuse these numbers in every sizing, venting and combustion-air calculation.
What the IFGC Governs — and Where It Stops
Maryland adopts the International Fuel Gas Code (IFGC) , the International Plumbing Code (IPC) , the International Residential Code (IRC) , NFPA 54 ( National Fuel Gas Code ) and NFPA 58 (LP-Gas) by reference at COMAR 09.20.01 . In the testing room the IFGC 2018 is your reference for anything that burns gas; the IPC 2018 covers water, waste and vent.
IFGC Section 401.1 draws the boundary: the code applies from the point of delivery to the connections with the appliances . The point of delivery is the outlet of the utility meter for natural gas, or the outlet of the second-stage regulator for LP-gas; upstream of it the utility or propane supplier owns the pipe and federal pipeline rules govern. The IFGC also does not reach systems operating above 125 psig for natural gas or 20 psig for LP-gas . Chapter 24 of the IRC is text extracted from the IFGC, so residential and commercial answers are the same rule under two numbers (IFGC 310.2 is IRC G2411.2).
Natural Gas vs. Propane: The Comparison Table to Memorize
- Property Natural gas (mostly methane) Commercial propane (LP-gas)
- Main constituent CH₄ (methane) C₃H₈ (propane)
- Specific gravity (air = 1.0) ≈ 0.60 (0.554 pure methane) ≈ 1.52 (sizing tables use 1.50)
- Behavior when released Rises, disperses upward Sinks, pools in low spots
- Heating value, vapor ≈ 1,000 Btu/ft³ (utility gas 950–1,050) ≈ 2,500 Btu/ft³
- Heating value, liquid Not applicable ≈ 91,500 Btu/gal
- Flammable (explosive) limits ≈ 5% LEL to 15% UEL (natural gas often listed 4–14%) ≈ 2.1% LEL to 9.5% UEL
- Air for complete combustion ≈ 10 ft³ air per ft³ gas (9.53 exact) ≈ 24 ft³ air per ft³ gas (23.8 exact)
Typical pressure at the appliance 7 in. w.c. 11 in. w.c.
Typical manifold (burner) pressure 3.5 in. w.c. 10 in. w.c.
Boiling point of the liquid −259°F (as LNG) −44°F
Specific gravity is the weight of a volume of gas compared with the same volume of air. Because propane is half again as heavy as air, a leak flows downhill and collects in basements, crawl spaces, pits and floor trenches — which is why NFPA 58 restricts LP-gas containers and certain appliances in below-grade spaces, and why propane detectors mount low . Natural gas at 0.60 gravity gathers at the ceiling, so its detectors mount high . Same leak, opposite search pattern.