Study guide

12.2 Appliance Clearances to Combustibles, Access & Location Limits

Maryland Journeyman Plumber Journey Plumber/Gas Fitter

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Maryland Licensing, Code Administration & the Exam

1.1 Maryland Plumbing Regulations & Licensing 1.2 The Journey Plumber/Gas Fitter Exam: Format, References & Open-Book Strategy

2 Chapter 2: Job-Site Safety & OSHA 29 CFR 1926

2.1 OSHA Construction Safety, PPE & Hazard Communication 2.2 Excavation & Trenching Safety (29 CFR 1926 Subpart P) 2.3 Confined Spaces, Ladders, Scaffolds & Hot Work

3 Chapter 3: Materials, Uses & Specifications

3.1 Approved Plumbing Materials, Pipes & Jointing 3.2 Hanger Spacing, Structural Protection & System Testing 3.3 Valves, Fittings, Fitting Selection & Prohibited Connections

4 Chapter 4: Sanitary Drainage & Waste Piping

4.1 Drainage Fixture Units (DFU) & Drain Pipe Sizing 4.2 Building Sewers, Cleanout Clearances & Underground Piping 4.3 Indirect & Special Waste Systems 4.4 Backwater Valves, Sump Pumps & Sewage Ejectors

5 Chapter 5: Venting Systems

5.1 Vent Sizing, Termination & Soil Stacks 5.2 Individual, Branch & Common Vents 5.3 Wet Venting & Circuit Venting 5.4 Air Admittance Valves (AAVs) & Special Venting

6 Chapter 6: Traps, Interceptors & Backwater Valves

6.1 Traps, Trap Seals & Trap Arm Requirements 6.2 Grease, Oil & Special-Waste Interceptors and Separators

7 Chapter 7: Water Supply & Distribution Systems

7.1 Water Supply Sizing & Fixture Unit (WSFU) Method 7.2 Water Heaters & Safety Devices 7.3 Pressure Regulation, Booster Systems & Disinfection 7.4 Water Service Piping, Meters, Valves & System Protection

8 Chapter 8: Backflow Prevention & Cross-Connection Control

8.1 Backflow Prevention & Cross-Connection Control 8.2 Air Gaps, Vacuum Breakers & Their Application Limits 8.3 Double Check & Reduced Pressure Principle (RPZ) Assemblies 8.4 Backflow Assembly Field Testing Procedures & Gauge Use 8.5 Maryland Backflow Program: 32-Hour Course, Certification & Reporting

9 Chapter 9: Fuel Gas Fundamentals, Materials & Pipe Sizing

9.1 Fuel Gas Properties, Heating Values & IFGC Scope 9.2 Fuel Gas Pipe Sizing & Materials 9.3 Approved Gas Piping Materials, CSST & Bonding 9.4 Gas Pipe Sizing Tables: Longest-Length & Branch-Length Methods 9.5 LP-Gas Systems, NFPA 58 & Propane-Specific Rules

10 Chapter 10: Gas Piping Installation, Testing & Purging

10.1 Gas Piping Installation, Testing & Purging 10.2 Gas Piping Support, Protection, Prohibited Locations & Concealed Piping 10.3 Shutoff Valves, Drips, Unions, Sediment Traps & Appliance Connectors 10.4 Gas Meters, Regulators, Pressure Levels & Overpressure Protection 10.5 Gas Leak Detection, Odorization & Emergency Response

11 Chapter 11: Gas Appliance Venting & Combustion Air

11.1 Gas Appliance Venting & Combustion Air 11.2 Appliance Categories I-IV, Vent Materials & Vent Connectors 11.3 Chimney & Vent Sizing Tables (Type B, Masonry & Common Venting) 11.4 Vent Termination, Clearances & Direct-Vent Systems 11.5 Combustion Air: Indoor & Outdoor Methods and Opening Sizing

12 Chapter 12: Gas Appliance Installation & Service

12.1 Gas Water Heaters, Furnaces & Boilers: Installation Rules 12.2 Appliance Clearances to Combustibles, Access & Location Limits 12.3 Gas Appliance Troubleshooting, Combustion Analysis & CO Safety

13 Chapter 13: Plumbing Fixtures, Fittings & Appliances

13.1 Fixture Clearances, Accessibility & Installation 13.2 Water Conservation Standards & Flow Rates 13.3 Commercial & Specialty Fixture Requirements

14 Chapter 14: Plumbing Mathematics

14.1 Plumbing Math I: Areas, Volumes, Capacities & Water Weight 14.2 Plumbing Math II: Offsets, Travel, Grade & Pipe Layout 14.3 Plumbing Math III: Gas Math, Meter Readings, BTU & Pressure Conversions

12.2 Appliance Clearances to Combustibles, Access & Location Limits

Key Takeaways Explain This Topic AI

IFGC 2018 Table 308.2 takes an 18-inch side and rear clearance down to 6 inches with 24-gage sheet metal on a ventilated airspace, and to 9 inches above the appliance.

IFGC 306.1 requires a level working space not less than 30 inches deep by 30 inches wide in front of the control side of every appliance.

IFGC 303.3 bars appliances from sleeping rooms, bathrooms, toilet rooms, storage closets and surgical rooms except under six listed exceptions, including direct-vent units.

A domestic dryer exhaust duct is limited to 35 feet, less 5 feet for each 4-inch radius mitered 90-degree elbow and 2 feet 6 inches for each mitered 45 (Table 614.8.4.1).

IFGC 614.4 forbids screens at the dryer termination and prohibits connecting a dryer exhaust duct to any vent connector, vent or chimney.

Last updated: July 2026

12.2 Appliance Clearances to Combustibles, Access & Location Limits

Quick Answer: IFGC 2018 Section 303.3 prohibits appliances in sleeping rooms, bathrooms, toilet rooms, storage closets and surgical rooms -- or in any space that opens only into such rooms -- unless one of six specific exceptions applies. The first and broadest is a direct-vent appliance installed in accordance with its listing and the manufacturer's instructions .

Clearance and location questions are the easiest points in the 40-question Gas Appliances and Piping domain because the answers are tabulated. The trap is that two different rules are in play: clearance to combustibles , which protects the building from the appliance, and access and working space , which protects the technician's ability to service it.

Listed Clearances Versus Reduced Clearances

IFGC 305.8 sets the baseline: heat-producing appliances maintain the clearances specified in the listing and the manufacturer's instructions , and those clearances "shall be reduced only in accordance with Section 308." The same section warns that clearance means real, permanent clearance -- it must account for door swing, drawer pull, overhead projections or shelving, and window swing , and door stops, limits and closers may not be used to create the required clearance .

Section 308 offers exactly two legal ways to reduce a clearance:

A reduced clearance protective assembly listed and labeled to UL 1618 , installed per its listing; or

One of the eight forms of protection in Table 308.2 , which is a lookup, not a percentage you calculate.

Where a needed distance is not printed in the table you may interpolate between the listed distances , but you may never extrapolate below the range of the table . And no reduction is permitted at all where the appliance or equipment listing specifically prohibits it.

Table 308.2 -- Selected Values (2018 IFGC)

Column 1 is the clearance above the appliance or a horizontal connector; column 2 is the clearance from the sides and rear , a vertical connector and single-wall metal pipe.

Form of protection applied to the combustible material 36 in required: above / sides 18 in required: above / sides 12 in required: above / sides

  • 3-1/2 in masonry wall, no ventilated airspace -- / 24 -- / 12 -- / 9
  • 1/2 in insulation board over 1 in glass fiber or mineral wool batts 24 / 18 12 / 9 9 / 6
  • 24-gage sheet metal with ventilated airspace 18 / 12 9 / 6 6 / 4
  • 1/2 in insulation board with ventilated airspace 18 / 12 9 / 6 6 / 4

The footnotes carry the installation principle, and they are examinable:

Air gap: a wall protector mounted on a flat wall away from corners needs a minimum 1-inch air gap , with the bottom and top edges, or the side and top edges, or all edges left open so air can circulate. Keep not less than 1 inch between the protection system and the combustible wall or ceiling.

Spacers and ties must be noncombustible , and no spacer or tie may be placed directly opposite the appliance or connector -- that would be a straight conduction path into the framing.

Not less than 1 inch must remain between the appliance and the protector.

Clearance is measured from the outer surface of the combustible material to the nearest point on the appliance, disregarding the protection applied to it .

Mineral wool batts need a minimum density of 8 pounds per cubic foot and a melting point of 1,500 degrees F ; insulation used in the assembly must have a thermal conductivity of 1.0 Btu-in/ft2-h-degree F or less .

No reduction may interfere with combustion air, draft hood clearance and relief, or accessibility for servicing .

Worked example. An appliance is listed for 18 inches to combustibles at the sides and rear. You install 24-gage sheet metal on a 1-inch ventilated airspace, extended far enough in each direction that the protected zone equals the unprotected clearance (Figure 308.2(1)). Table 308.2 gives 6 inches -- a reduction of 12 inches, or 12/18 = 67 percent . Above the appliance the same protection takes 18 inches down to 9 inches , only 50 percent, which is why you must read the correct column instead of applying one percentage everywhere.