Study guide
11.2 Appliance Categories I-IV, Vent Materials & Vent Connectors
Maryland Journeyman Plumber Journey Plumber/Gas Fitter
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Maryland Licensing, Code Administration & the Exam
1.1 Maryland Plumbing Regulations & Licensing 1.2 The Journey Plumber/Gas Fitter Exam: Format, References & Open-Book Strategy
2 Chapter 2: Job-Site Safety & OSHA 29 CFR 1926
2.1 OSHA Construction Safety, PPE & Hazard Communication 2.2 Excavation & Trenching Safety (29 CFR 1926 Subpart P) 2.3 Confined Spaces, Ladders, Scaffolds & Hot Work
3 Chapter 3: Materials, Uses & Specifications
3.1 Approved Plumbing Materials, Pipes & Jointing 3.2 Hanger Spacing, Structural Protection & System Testing 3.3 Valves, Fittings, Fitting Selection & Prohibited Connections
4 Chapter 4: Sanitary Drainage & Waste Piping
4.1 Drainage Fixture Units (DFU) & Drain Pipe Sizing 4.2 Building Sewers, Cleanout Clearances & Underground Piping 4.3 Indirect & Special Waste Systems 4.4 Backwater Valves, Sump Pumps & Sewage Ejectors
5 Chapter 5: Venting Systems
5.1 Vent Sizing, Termination & Soil Stacks 5.2 Individual, Branch & Common Vents 5.3 Wet Venting & Circuit Venting 5.4 Air Admittance Valves (AAVs) & Special Venting
6 Chapter 6: Traps, Interceptors & Backwater Valves
6.1 Traps, Trap Seals & Trap Arm Requirements 6.2 Grease, Oil & Special-Waste Interceptors and Separators
7 Chapter 7: Water Supply & Distribution Systems
7.1 Water Supply Sizing & Fixture Unit (WSFU) Method 7.2 Water Heaters & Safety Devices 7.3 Pressure Regulation, Booster Systems & Disinfection 7.4 Water Service Piping, Meters, Valves & System Protection
8 Chapter 8: Backflow Prevention & Cross-Connection Control
8.1 Backflow Prevention & Cross-Connection Control 8.2 Air Gaps, Vacuum Breakers & Their Application Limits 8.3 Double Check & Reduced Pressure Principle (RPZ) Assemblies 8.4 Backflow Assembly Field Testing Procedures & Gauge Use 8.5 Maryland Backflow Program: 32-Hour Course, Certification & Reporting
9 Chapter 9: Fuel Gas Fundamentals, Materials & Pipe Sizing
9.1 Fuel Gas Properties, Heating Values & IFGC Scope 9.2 Fuel Gas Pipe Sizing & Materials 9.3 Approved Gas Piping Materials, CSST & Bonding 9.4 Gas Pipe Sizing Tables: Longest-Length & Branch-Length Methods 9.5 LP-Gas Systems, NFPA 58 & Propane-Specific Rules
10 Chapter 10: Gas Piping Installation, Testing & Purging
10.1 Gas Piping Installation, Testing & Purging 10.2 Gas Piping Support, Protection, Prohibited Locations & Concealed Piping 10.3 Shutoff Valves, Drips, Unions, Sediment Traps & Appliance Connectors 10.4 Gas Meters, Regulators, Pressure Levels & Overpressure Protection 10.5 Gas Leak Detection, Odorization & Emergency Response
11 Chapter 11: Gas Appliance Venting & Combustion Air
11.1 Gas Appliance Venting & Combustion Air 11.2 Appliance Categories I-IV, Vent Materials & Vent Connectors 11.3 Chimney & Vent Sizing Tables (Type B, Masonry & Common Venting) 11.4 Vent Termination, Clearances & Direct-Vent Systems 11.5 Combustion Air: Indoor & Outdoor Methods and Opening Sizing
12 Chapter 12: Gas Appliance Installation & Service
12.1 Gas Water Heaters, Furnaces & Boilers: Installation Rules 12.2 Appliance Clearances to Combustibles, Access & Location Limits 12.3 Gas Appliance Troubleshooting, Combustion Analysis & CO Safety
13 Chapter 13: Plumbing Fixtures, Fittings & Appliances
13.1 Fixture Clearances, Accessibility & Installation 13.2 Water Conservation Standards & Flow Rates 13.3 Commercial & Specialty Fixture Requirements
14 Chapter 14: Plumbing Mathematics
14.1 Plumbing Math I: Areas, Volumes, Capacities & Water Weight 14.2 Plumbing Math II: Offsets, Travel, Grade & Pipe Layout 14.3 Plumbing Math III: Gas Math, Meter Readings, BTU & Pressure Conversions
11.2 Appliance Categories I-IV, Vent Materials & Vent Connectors
Key Takeaways Explain This Topic AI
IFGC 2018 defines the four vented appliance categories by vent static pressure and condensate potential only: Category I non-positive and non-condensing, II non-positive and condensing, III positive and non-condensing, IV positive and condensing.
IFGC 2018 Section 503.10.8 limits a single-wall vent connector to 75 percent of the chimney or vent height and a Type B double-wall connector to 100 percent, while Table 504.3.2 caps common-vent connectors at 1 1/2 feet per inch of diameter.
IFGC 2018 Section 503.10.7 requires a vent connector to be installed without dips or sags and to slope upward toward the vent not less than 1/4 inch per foot.
IFGC 2018 Table 503.10.5 requires 6 inches of clearance from single-wall metal pipe to combustibles for listed draft-hood appliances, 9 inches for unlisted draft-hood appliances and 36 inches for medium-heat appliances.
IFGC 2018 Section 503.13 prohibits a manually operated damper in the vent connector for any appliance; only a listed automatically operated vent damper is permitted under Section 503.14.
Last updated: July 2026
11.2 Appliance Categories I-IV, Vent Materials & Vent Connectors
Quick Answer: The four vented appliance categories are defined by exactly two variables - vent static pressure (non-positive or positive) and whether the vent gas temperature is capable of causing excessive condensate in the vent. Category I (non-positive, non-condensing) is the only category the IFGC itself sizes; Categories II, III and IV are designed, sized and installed strictly per the appliance manufacturer's instructions (IFGC 2018 Section 501.14).
Two Variables, Four Boxes
The International Fuel Gas Code (IFGC) and NFPA 54, National Fuel Gas Code classify vented appliances for exactly one purpose: choosing a vent. Both variables are pass/fail, so two variables produce four categories. Nothing about efficiency, fuel or appliance type enters the definition.
Category Vent static pressure Vent gas temperature Plain English Typical appliance
I Non-positive Avoids excessive condensate Non-condensing, negative pressure Atmospheric water heater; draft-hood or 80-percent fan-assisted furnace
II Non-positive Capable of causing excessive condensate Condensing, negative pressure Uncommon in residential work; some commercial boilers
III Positive Avoids excessive condensate Non-condensing, positive pressure Power-vented water heater, some unit heaters
IV Positive Capable of causing excessive condensate Condensing, positive pressure 90-percent-plus condensing furnace, boiler or tankless water heater
Two consequences follow immediately. A draft hood can appear only on a Category I appliance, because a draft hood dilutes flue gas with room air and cannot hold positive pressure. A fan-assisted combustion system - an appliance with an integral mechanical means of drawing or forcing products of combustion through the heat exchanger (IFGC 504.1) - can land in any of the four categories, so you cannot classify an appliance by spotting its blower.
The temperature number that is not in the code
Trade references routinely say "Category I is above 275 degrees F, Category IV is below 275 degrees F." Read the actual definition and no number appears: the code says a vent gas temperature that avoids excessive condensate production (Categories I and III) or is capable of causing it (Categories II and IV). The 275 degree figure belongs to UL vent-temperature classes, not to the category definitions. On an open-book exam, look the definition up instead of reciting the number.
What Vent Material Each Category Requires
IFGC 2018 Table 503.4 assigns the venting system by appliance, and Section 501.14 hands Categories II, III and IV to the manufacturer.
Category Permitted venting system Governing listing
I Type B gas vent; masonry, metal or factory-built chimney; listed chimney lining system for gas venting; single-wall metal pipe within its limits; special gas vent listed for these appliances UL 441 (Type B), UL 103 (factory-built chimney), UL 1777 (liner), UL 1738 (special gas vent)
II As specified or furnished by the appliance manufacturer UL 1738
III As specified by the manufacturer - gas-tight positive-pressure vent, commonly AL29-4C superferritic stainless UL 1738
IV As specified by the manufacturer - PVC, CPVC, polypropylene or AL29-4C stainless UL 1738, or the product standard the appliance manufacturer names
Section 502.1 carves out one exception worth memorizing: plastic vents for Category IV appliances are not required to be listed and labeled where the vent is specified by the appliance manufacturer and installed per that manufacturer's instructions. Section 503.4.1 still requires the appliance itself to be listed for plastic venting and the instructions to identify the specific plastic, and 503.4.1.1 requires primer, where used, to be a contrasting color so an inspector can confirm it was applied.
Two hard prohibitions police the boundary between categories. Section 501.6 requires a venting system that will see positive pressure to be designed for positive-pressure application, and 503.5.1 requires a factory-built chimney serving a positive-pressure appliance to be listed for that use. Section 503.10.4 forbids connecting a Category I vent connector to any portion of a mechanical draft system operating under positive static pressure , such as one serving a Category III or IV appliance.
Type B, Type B-W and Type L: Three Different Jobs
Type B gas vent - double-wall construction, aluminum inner liner inside a galvanized outer wall with an insulating air space, listed to UL 441 . It serves listed Category I appliances, appliances equipped with draft hoods, and appliances listed for use with Type B vent. It terminates not less than 5 feet in vertical height above the highest connected draft hood outlet or flue collar (503.6.6). Table 503.10.5 lists its clearance to combustibles as "as listed" - the common listing is 1 inch, but the label governs, not a remembered number.
Type B-W gas vent - the oval Type B variant listed for listed vented wall furnaces only (Table 503.4). Its listed capacity must be not less than that of the wall furnace it serves (503.6.3), and it terminates not less than 12 feet in vertical height above the bottom of the wall furnace (503.6.6).
Type L vent - low-temperature venting listed to UL 641 , the venting system for listed combination gas- and oil-burning appliances and for residential appliances listed for use with Type L. Table 503.10.5 permits Type L in several places where Type B is "not permitted," such as unlisted residential appliances with draft hoods.
Section 503.6.14 adds a rule inspectors write up constantly: screws, rivets and other fasteners shall not penetrate the inner wall of a double-wall gas vent , except at the transition from a draft hood outlet, flue collar or single-wall metal connector into the double-wall vent.