Study guide

11.4 Vent Termination, Clearances & Direct-Vent Systems

Maryland Journeyman Plumber Journey Plumber/Gas Fitter

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Maryland Licensing, Code Administration & the Exam

1.1 Maryland Plumbing Regulations & Licensing 1.2 The Journey Plumber/Gas Fitter Exam: Format, References & Open-Book Strategy

2 Chapter 2: Job-Site Safety & OSHA 29 CFR 1926

2.1 OSHA Construction Safety, PPE & Hazard Communication 2.2 Excavation & Trenching Safety (29 CFR 1926 Subpart P) 2.3 Confined Spaces, Ladders, Scaffolds & Hot Work

3 Chapter 3: Materials, Uses & Specifications

3.1 Approved Plumbing Materials, Pipes & Jointing 3.2 Hanger Spacing, Structural Protection & System Testing 3.3 Valves, Fittings, Fitting Selection & Prohibited Connections

4 Chapter 4: Sanitary Drainage & Waste Piping

4.1 Drainage Fixture Units (DFU) & Drain Pipe Sizing 4.2 Building Sewers, Cleanout Clearances & Underground Piping 4.3 Indirect & Special Waste Systems 4.4 Backwater Valves, Sump Pumps & Sewage Ejectors

5 Chapter 5: Venting Systems

5.1 Vent Sizing, Termination & Soil Stacks 5.2 Individual, Branch & Common Vents 5.3 Wet Venting & Circuit Venting 5.4 Air Admittance Valves (AAVs) & Special Venting

6 Chapter 6: Traps, Interceptors & Backwater Valves

6.1 Traps, Trap Seals & Trap Arm Requirements 6.2 Grease, Oil & Special-Waste Interceptors and Separators

7 Chapter 7: Water Supply & Distribution Systems

7.1 Water Supply Sizing & Fixture Unit (WSFU) Method 7.2 Water Heaters & Safety Devices 7.3 Pressure Regulation, Booster Systems & Disinfection 7.4 Water Service Piping, Meters, Valves & System Protection

8 Chapter 8: Backflow Prevention & Cross-Connection Control

8.1 Backflow Prevention & Cross-Connection Control 8.2 Air Gaps, Vacuum Breakers & Their Application Limits 8.3 Double Check & Reduced Pressure Principle (RPZ) Assemblies 8.4 Backflow Assembly Field Testing Procedures & Gauge Use 8.5 Maryland Backflow Program: 32-Hour Course, Certification & Reporting

9 Chapter 9: Fuel Gas Fundamentals, Materials & Pipe Sizing

9.1 Fuel Gas Properties, Heating Values & IFGC Scope 9.2 Fuel Gas Pipe Sizing & Materials 9.3 Approved Gas Piping Materials, CSST & Bonding 9.4 Gas Pipe Sizing Tables: Longest-Length & Branch-Length Methods 9.5 LP-Gas Systems, NFPA 58 & Propane-Specific Rules

10 Chapter 10: Gas Piping Installation, Testing & Purging

10.1 Gas Piping Installation, Testing & Purging 10.2 Gas Piping Support, Protection, Prohibited Locations & Concealed Piping 10.3 Shutoff Valves, Drips, Unions, Sediment Traps & Appliance Connectors 10.4 Gas Meters, Regulators, Pressure Levels & Overpressure Protection 10.5 Gas Leak Detection, Odorization & Emergency Response

11 Chapter 11: Gas Appliance Venting & Combustion Air

11.1 Gas Appliance Venting & Combustion Air 11.2 Appliance Categories I-IV, Vent Materials & Vent Connectors 11.3 Chimney & Vent Sizing Tables (Type B, Masonry & Common Venting) 11.4 Vent Termination, Clearances & Direct-Vent Systems 11.5 Combustion Air: Indoor & Outdoor Methods and Opening Sizing

12 Chapter 12: Gas Appliance Installation & Service

12.1 Gas Water Heaters, Furnaces & Boilers: Installation Rules 12.2 Appliance Clearances to Combustibles, Access & Location Limits 12.3 Gas Appliance Troubleshooting, Combustion Analysis & CO Safety

13 Chapter 13: Plumbing Fixtures, Fittings & Appliances

13.1 Fixture Clearances, Accessibility & Installation 13.2 Water Conservation Standards & Flow Rates 13.3 Commercial & Specialty Fixture Requirements

14 Chapter 14: Plumbing Mathematics

14.1 Plumbing Math I: Areas, Volumes, Capacities & Water Weight 14.2 Plumbing Math II: Offsets, Travel, Grade & Pipe Layout 14.3 Plumbing Math III: Gas Math, Meter Readings, BTU & Pressure Conversions

11.4 Vent Termination, Clearances & Direct-Vent Systems

Key Takeaways Explain This Topic AI

IFGC 2018 Figure 503.6.5 sets gas vent height by roof pitch: 1.0 foot flat through 6/12, 1.5 feet over 7/12 to 8/12, 2.0 feet over 8/12 to 9/12, and 8.0 feet over 20/12 to 21/12.

A gas vent over 12 inches in size, or standing less than 8 feet from a vertical wall, must terminate 2 feet above the roof penetration and 2 feet above any portion of the building within 10 feet horizontally (IFGC 2018 Section 503.6.5, Item 2).

Chimneys for residential or low-heat appliances follow the 3-2-10 rule: 3 feet above the roof penetration, 2 feet above any building portion within 10 feet, and 5 feet above the highest connected draft hood outlet (IFGC 2018 Section 503.5.4).

IFGC 2018 Table 503.8 gives direct-vent terminal clearance from any air opening as 6 inches under 10,000 Btu/h, 9 inches from 10,000 through 50,000 Btu/h, and 12 inches over 50,000 through 150,000 Btu/h.

A mechanical draft vent other than direct-vent must terminate 4 feet below, 4 feet horizontally from, or 1 foot above any door, operable window or gravity air inlet, with the bottom of the terminal not less than 12 inches above finished ground level.

Last updated: July 2026

11.4 Vent Termination, Clearances & Direct-Vent Systems

Quick Answer: A gas vent 12 inches or less in size standing at least 8 feet from a vertical wall terminates at the height given in IFGC 2018 Figure 503.6.5 -- 1.0 foot above the roof for pitches flat through 6/12. Every other gas vent must terminate 2 feet above the roof penetration and 2 feet above any portion of the building within 10 feet horizontally .

Gas Appliances and Piping is 40 of the 100 scored questions on the Maryland Journey Plumber/Gas Fitter exam, and termination clearances are the most heavily tested slice of that domain because every answer is a hard, lookup-able number. The International Fuel Gas Code (IFGC) 2018 is an allowed open-book reference, so the exam rewards knowing which section holds the number rather than memorizing all of them. Input ratings below are in British thermal units per hour (Btu/h) .

Roof Terminations: Two Different Paths

IFGC 2018 Section 503.6.5 splits gas vents into two cases, and picking the wrong one is the classic error.

Path 1 -- the roof-pitch table. A gas vent 12 inches or less in size that stands not less than 8 feet from a vertical wall or similar obstruction terminates at height H above the roof, measured to the lowest discharge opening of the listed cap:

  • Roof slope H (minimum), feet
  • Flat to 6/12 1.0
  • Over 6/12 to 7/12 1.25
  • Over 7/12 to 8/12 1.5
  • Over 8/12 to 9/12 2.0
  • Over 9/12 to 10/12 2.5
  • Over 10/12 to 11/12 3.25
  • Over 11/12 to 12/12 4.0
  • Over 12/12 to 14/12 5.0
  • Over 14/12 to 16/12 6.0
  • Over 16/12 to 18/12 7.0
  • Over 18/12 to 20/12 7.5
  • Over 20/12 to 21/12 8.0

Read the rows as ranges , not as single pitches. A 9/12 roof sits at the top of the 'Over 8/12 to 9/12' band and needs 2.0 feet , not the 2.5 feet printed on the next line.

Path 2 -- the 2-2-10 rule. A gas vent that is over 12 inches in size , or that stands less than 8 feet from a vertical wall , loses the table entirely. It must terminate 2 feet above the highest point where it passes through the roof and 2 feet above any portion of a building within 10 feet horizontally . Both conditions apply and you build to the taller result.

Worked Example

A 5-inch Type B vent penetrates a 10/12 roof only 6 feet from a two-story wall. The vent is under 12 inches, but it is closer than 8 feet to a vertical wall, so Path 1 is unavailable. Under Path 2 it must rise 2 feet above the penetration and 2 feet above the top of any construction within 10 feet. If that wall rises 9 feet above the penetration point, the vent must extend 11 feet -- not the 2.5 feet the pitch table would have suggested.

Minimum height above the appliance (Section 503.6.6). Independently of the roof geometry, a Type B or Type L gas vent must terminate not less than 5 feet in vertical height above the highest connected appliance draft hood or flue collar , and a Type B-W vent serving a wall furnace must terminate not less than 12 feet above the bottom of the wall furnace . Short single-story vents routinely fail this rule even when the roof height checks out.