Study guide
2.3 Confined Spaces, Ladders, Scaffolds & Hot Work
Maryland Journeyman Plumber Journey Plumber/Gas Fitter
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Maryland Licensing, Code Administration & the Exam
1.1 Maryland Plumbing Regulations & Licensing 1.2 The Journey Plumber/Gas Fitter Exam: Format, References & Open-Book Strategy
2 Chapter 2: Job-Site Safety & OSHA 29 CFR 1926
2.1 OSHA Construction Safety, PPE & Hazard Communication 2.2 Excavation & Trenching Safety (29 CFR 1926 Subpart P) 2.3 Confined Spaces, Ladders, Scaffolds & Hot Work
3 Chapter 3: Materials, Uses & Specifications
3.1 Approved Plumbing Materials, Pipes & Jointing 3.2 Hanger Spacing, Structural Protection & System Testing 3.3 Valves, Fittings, Fitting Selection & Prohibited Connections
4 Chapter 4: Sanitary Drainage & Waste Piping
4.1 Drainage Fixture Units (DFU) & Drain Pipe Sizing 4.2 Building Sewers, Cleanout Clearances & Underground Piping 4.3 Indirect & Special Waste Systems 4.4 Backwater Valves, Sump Pumps & Sewage Ejectors
5 Chapter 5: Venting Systems
5.1 Vent Sizing, Termination & Soil Stacks 5.2 Individual, Branch & Common Vents 5.3 Wet Venting & Circuit Venting 5.4 Air Admittance Valves (AAVs) & Special Venting
6 Chapter 6: Traps, Interceptors & Backwater Valves
6.1 Traps, Trap Seals & Trap Arm Requirements 6.2 Grease, Oil & Special-Waste Interceptors and Separators
7 Chapter 7: Water Supply & Distribution Systems
7.1 Water Supply Sizing & Fixture Unit (WSFU) Method 7.2 Water Heaters & Safety Devices 7.3 Pressure Regulation, Booster Systems & Disinfection 7.4 Water Service Piping, Meters, Valves & System Protection
8 Chapter 8: Backflow Prevention & Cross-Connection Control
8.1 Backflow Prevention & Cross-Connection Control 8.2 Air Gaps, Vacuum Breakers & Their Application Limits 8.3 Double Check & Reduced Pressure Principle (RPZ) Assemblies 8.4 Backflow Assembly Field Testing Procedures & Gauge Use 8.5 Maryland Backflow Program: 32-Hour Course, Certification & Reporting
9 Chapter 9: Fuel Gas Fundamentals, Materials & Pipe Sizing
9.1 Fuel Gas Properties, Heating Values & IFGC Scope 9.2 Fuel Gas Pipe Sizing & Materials 9.3 Approved Gas Piping Materials, CSST & Bonding 9.4 Gas Pipe Sizing Tables: Longest-Length & Branch-Length Methods 9.5 LP-Gas Systems, NFPA 58 & Propane-Specific Rules
10 Chapter 10: Gas Piping Installation, Testing & Purging
10.1 Gas Piping Installation, Testing & Purging 10.2 Gas Piping Support, Protection, Prohibited Locations & Concealed Piping 10.3 Shutoff Valves, Drips, Unions, Sediment Traps & Appliance Connectors 10.4 Gas Meters, Regulators, Pressure Levels & Overpressure Protection 10.5 Gas Leak Detection, Odorization & Emergency Response
11 Chapter 11: Gas Appliance Venting & Combustion Air
11.1 Gas Appliance Venting & Combustion Air 11.2 Appliance Categories I-IV, Vent Materials & Vent Connectors 11.3 Chimney & Vent Sizing Tables (Type B, Masonry & Common Venting) 11.4 Vent Termination, Clearances & Direct-Vent Systems 11.5 Combustion Air: Indoor & Outdoor Methods and Opening Sizing
12 Chapter 12: Gas Appliance Installation & Service
12.1 Gas Water Heaters, Furnaces & Boilers: Installation Rules 12.2 Appliance Clearances to Combustibles, Access & Location Limits 12.3 Gas Appliance Troubleshooting, Combustion Analysis & CO Safety
13 Chapter 13: Plumbing Fixtures, Fittings & Appliances
13.1 Fixture Clearances, Accessibility & Installation 13.2 Water Conservation Standards & Flow Rates 13.3 Commercial & Specialty Fixture Requirements
14 Chapter 14: Plumbing Mathematics
14.1 Plumbing Math I: Areas, Volumes, Capacities & Water Weight 14.2 Plumbing Math II: Offsets, Travel, Grade & Pipe Layout 14.3 Plumbing Math III: Gas Math, Meter Readings, BTU & Pressure Conversions
2.3 Confined Spaces, Ladders, Scaffolds & Hot Work
Key Takeaways Explain This Topic AI
Acceptable oxygen in a permit-required confined space is 19.5 percent to 23.5 percent by volume; readings outside that range define a hazardous atmosphere under 1926.1202.
1926.1204(e)(3) requires atmospheric testing in a fixed order: oxygen first, then combustible gases and vapors, then toxic gases and vapors.
Portable ladder side rails must extend at least 3 feet above the upper landing surface (1926.1053(b)(1)), and the base is set out about one-quarter of the working length (4:1).
Scaffold fall protection is required more than 10 feet above a lower level, and every scaffold must support at least 4 times its maximum intended load (1926.451).
Oxygen cylinders in storage must be at least 20 feet from fuel-gas cylinders or separated by a noncombustible barrier at least 5 feet high rated at one-half hour (1926.350(a)(10)).
Last updated: November 2026
2.3 Confined Spaces, Ladders, Scaffolds & Hot Work
Quick Answer: In a permit-required confined space the acceptable oxygen range is 19.5 percent to 23.5 percent by volume, and 1926.1204(e)(3) requires atmospheric testing in a fixed order: oxygen first, then combustible gases and vapors, then toxic gases and vapors . For portable ladders, side rails must extend at least 3 feet above the upper landing surface (1926.1053(b)(1)) and the base is set out about one-quarter of the working length - the 4:1 pitch rule (1926.1053(b)(5)(i)).
Subpart AA - Confined Spaces in Construction
Subpart AA (1926.1201 through 1926.1213) governs confined-space entry on construction sites. A confined space meets all three of these tests:
- It is large enough and so configured that an employee can bodily enter it;
- It has limited or restricted means for entry and exit ; and
It is not designed for continuous employee occupancy .
It becomes a permit-required confined space (PRCS) if it has any one of four characteristics:
- Contains or has the potential to contain a hazardous atmosphere ;
- Contains a material with the potential for engulfing an entrant;
Has an internal configuration such that an entrant could be trapped or asphyxiated by inwardly converging walls, or by a floor that slopes downward and tapers to a smaller cross-section;
Contains any other recognized serious safety or health hazard .
Plumbing spaces that almost always qualify:
- Space Primary hazards
- Sanitary or storm manhole Hydrogen sulfide, methane, oxygen deficiency, engulfment, traffic
- Sewage wet well or lift station Hydrogen sulfide, methane, engulfment, electrical, rotating equipment
- Septic tank Hydrogen sulfide, oxygen deficiency, engulfment
- Deep sump or sewage ejector pit Oxygen deficiency, methane, mechanical hazards
- Water meter or valve vault Oxygen deficiency, flooding, traffic loading
- Boiler or interceptor pit Fuel gas, carbon monoxide, chemical, heat
- Hazardous atmosphere - the numbers
An atmosphere is hazardous if any one of the following is true:
- Oxygen below 19.5 percent or above 23.5 percent by volume;
- Flammable gas, vapor, or mist in excess of 10 percent of its lower flammable limit (LFL) ;
- Airborne combustible dust at or above its LFL;
- Any substance in a concentration above its permissible exposure limit (PEL) ;
Any other atmospheric condition that is immediately dangerous to life or health (IDLH) .
Methane has an LFL of roughly 5 percent by volume , so 10 percent of the LFL is 0.5 percent by volume, about 5,000 ppm - and that, not 5 percent, is the evacuation number. Methane is lighter than air and collects at the top of a manhole. Hydrogen sulfide (H2S) is heavier than air and pools at the bottom of a wet well or septic tank. OSHA's construction PEL for H2S is 10 ppm as an 8-hour TWA (1926.55, Table 1); the general-industry limit is a 20 ppm ceiling with a 50 ppm peak for 10 minutes once per shift if no other measurable exposure occurs; NIOSH lists the IDLH at 100 ppm . Its rotten-egg odor disappears at high concentration because of olfactory paralysis, so never treat your nose as a gas detector .
Why the testing order is fixed
Test oxygen first because the catalytic-bead sensor that reads combustible gas needs oxygen to burn the sample; in an oxygen-deficient space the LEL channel reads falsely low and a lethal atmosphere looks clean. Test combustibles second , because an explosion acts faster than a toxin. Test toxics last . Reversing that order is a favorite distractor.
Roles under Subpart AA
Role Standard Core duty
Entry supervisor 1926.1210 Determines that acceptable entry conditions exist, authorizes and terminates entry, verifies rescue services are available
Authorized entrant 1926.1208 Knows the hazards, uses assigned equipment, communicates with the attendant, self-evacuates on any warning sign
Attendant 1926.1209 Stationed outside the space, tracks entrants, monitors conditions, orders evacuation, summons rescue - and does not enter to attempt rescue
Rescue and emergency services 1926.1211 Non-entry retrieval whenever it is feasible
1926.1211 requires a retrieval system whenever an authorized entrant enters a permit space, unless the retrieval equipment would increase overall risk or would not contribute to rescue. The retrieval line attaches to a chest or full-body harness at the center of the entrant's back near shoulder level, or above the entrant's head , and a mechanical device - tripod and winch - must be available to retrieve entrants from vertical type permit spaces more than 5 feet deep . If an entrant is exposed to a substance for which a Safety Data Sheet exists, that SDS must be made available to the medical facility treating the entrant .
Exam Trap: More oxygen is not safer. 23.5 percent is an upper limit , not a comfort margin. An oxygen-enriched atmosphere - created by a leaking oxygen hose in a vault, or by someone "freshening" a space with an oxygen bottle - makes clothing, grease, and hair ignite violently. Any reading above 23.5 percent or below 19.5 percent is a hazardous atmosphere, and the answer choice that says "purge the space with oxygen" is always wrong. You ventilate with clean, breathable air .