Study guide

14.1 Plumbing Math I: Areas, Volumes, Capacities & Water Weight

Maryland Journeyman Plumber Journey Plumber/Gas Fitter

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Maryland Licensing, Code Administration & the Exam

1.1 Maryland Plumbing Regulations & Licensing 1.2 The Journey Plumber/Gas Fitter Exam: Format, References & Open-Book Strategy

2 Chapter 2: Job-Site Safety & OSHA 29 CFR 1926

2.1 OSHA Construction Safety, PPE & Hazard Communication 2.2 Excavation & Trenching Safety (29 CFR 1926 Subpart P) 2.3 Confined Spaces, Ladders, Scaffolds & Hot Work

3 Chapter 3: Materials, Uses & Specifications

3.1 Approved Plumbing Materials, Pipes & Jointing 3.2 Hanger Spacing, Structural Protection & System Testing 3.3 Valves, Fittings, Fitting Selection & Prohibited Connections

4 Chapter 4: Sanitary Drainage & Waste Piping

4.1 Drainage Fixture Units (DFU) & Drain Pipe Sizing 4.2 Building Sewers, Cleanout Clearances & Underground Piping 4.3 Indirect & Special Waste Systems 4.4 Backwater Valves, Sump Pumps & Sewage Ejectors

5 Chapter 5: Venting Systems

5.1 Vent Sizing, Termination & Soil Stacks 5.2 Individual, Branch & Common Vents 5.3 Wet Venting & Circuit Venting 5.4 Air Admittance Valves (AAVs) & Special Venting

6 Chapter 6: Traps, Interceptors & Backwater Valves

6.1 Traps, Trap Seals & Trap Arm Requirements 6.2 Grease, Oil & Special-Waste Interceptors and Separators

7 Chapter 7: Water Supply & Distribution Systems

7.1 Water Supply Sizing & Fixture Unit (WSFU) Method 7.2 Water Heaters & Safety Devices 7.3 Pressure Regulation, Booster Systems & Disinfection 7.4 Water Service Piping, Meters, Valves & System Protection

8 Chapter 8: Backflow Prevention & Cross-Connection Control

8.1 Backflow Prevention & Cross-Connection Control 8.2 Air Gaps, Vacuum Breakers & Their Application Limits 8.3 Double Check & Reduced Pressure Principle (RPZ) Assemblies 8.4 Backflow Assembly Field Testing Procedures & Gauge Use 8.5 Maryland Backflow Program: 32-Hour Course, Certification & Reporting

9 Chapter 9: Fuel Gas Fundamentals, Materials & Pipe Sizing

9.1 Fuel Gas Properties, Heating Values & IFGC Scope 9.2 Fuel Gas Pipe Sizing & Materials 9.3 Approved Gas Piping Materials, CSST & Bonding 9.4 Gas Pipe Sizing Tables: Longest-Length & Branch-Length Methods 9.5 LP-Gas Systems, NFPA 58 & Propane-Specific Rules

10 Chapter 10: Gas Piping Installation, Testing & Purging

10.1 Gas Piping Installation, Testing & Purging 10.2 Gas Piping Support, Protection, Prohibited Locations & Concealed Piping 10.3 Shutoff Valves, Drips, Unions, Sediment Traps & Appliance Connectors 10.4 Gas Meters, Regulators, Pressure Levels & Overpressure Protection 10.5 Gas Leak Detection, Odorization & Emergency Response

11 Chapter 11: Gas Appliance Venting & Combustion Air

11.1 Gas Appliance Venting & Combustion Air 11.2 Appliance Categories I-IV, Vent Materials & Vent Connectors 11.3 Chimney & Vent Sizing Tables (Type B, Masonry & Common Venting) 11.4 Vent Termination, Clearances & Direct-Vent Systems 11.5 Combustion Air: Indoor & Outdoor Methods and Opening Sizing

12 Chapter 12: Gas Appliance Installation & Service

12.1 Gas Water Heaters, Furnaces & Boilers: Installation Rules 12.2 Appliance Clearances to Combustibles, Access & Location Limits 12.3 Gas Appliance Troubleshooting, Combustion Analysis & CO Safety

13 Chapter 13: Plumbing Fixtures, Fittings & Appliances

13.1 Fixture Clearances, Accessibility & Installation 13.2 Water Conservation Standards & Flow Rates 13.3 Commercial & Specialty Fixture Requirements

14 Chapter 14: Plumbing Mathematics

14.1 Plumbing Math I: Areas, Volumes, Capacities & Water Weight 14.2 Plumbing Math II: Offsets, Travel, Grade & Pipe Layout 14.3 Plumbing Math III: Gas Math, Meter Readings, BTU & Pressure Conversions

14.1 Plumbing Math I: Areas, Volumes, Capacities & Water Weight

Key Takeaways Explain This Topic AI

One cubic foot holds 7.48 gallons, so the official PSI sample tank of 8 ft × 4.5 ft × 6 ft = 216 cubic feet holds 216 × 7.48 = 1,615.68 gallons.

One gallon of water weighs 8.33 pounds and one cubic foot of water weighs 62.4 pounds; one U.S. gallon is exactly 231 cubic inches.

1 psi equals 2.31 feet of head and 1 foot of head equals 0.433 psi, so a fixture 60.5 feet above the meter loses 60.5 × 0.433 = 26.2 psi of static pressure.

Use A = 0.7854 × d² instead of πr² when a problem gives a diameter; 0.7854 is π ÷ 4, and it eliminates the radius-versus-diameter error.

IPC 2018 Table 704.1 slopes convert to percent grade as 1/4 inch per foot = 2.08%, 1/8 inch per foot = 1.04%, and 1/16 inch per foot = 0.52%.

Last updated: July 2026

14.1 Plumbing Math I: Areas, Volumes, Capacities & Water Weight

Quick Answer: Volume in cubic feet × 7.48 = gallons. The official PSI sample question — a tank 8 feet long, 4 1/2 feet wide and 6 feet deep — works out to 8 × 4.5 × 6 = 216 cubic feet, and 216 × 7.48 = 1,615.68 gallons .

Plumbing Mathematics is 7 of the 100 scored questions on the Maryland Journey Plumber/Gas Fitter exam, and the Board lets you carry Mathematics for Plumbers and Pipefitters (Lee Smith, 8th edition) plus a non-programmable calculator into the testing room. That combination makes these seven the most reliably winnable points on the exam — the arithmetic is elementary, but only if the conversion constants and geometry formulas are already in your head instead of being hunted for with the clock running.

The Conversion Constants You Must Know Cold

  • Convert from To Multiply by Where it comes from
  • Cubic feet (ft³) Gallons 7.48 1,728 in³ ÷ 231 in³ = 7.4805
  • Gallons Cubic feet 0.1337 reciprocal of 7.48
  • Gallons Cubic inches 231 exact, by definition of the U.S. gallon
  • Cubic feet Cubic inches 1,728 12 × 12 × 12
  • Cubic yards Cubic feet 27 3 × 3 × 3
  • Gallons of water Pounds 8.33 weight of water at ordinary service temperature
  • Cubic feet of water Pounds 62.4 7.48 gal × 8.34 lb
  • psi Feet of head 2.31 height of a water column exerting 1 psi
  • Feet of head psi 0.433 reciprocal of 2.31
  • Inches Decimal feet ÷ 12 0.0833 ft per inch

Some reference tables print 8.34 pounds per gallon rather than 8.33, because 62.4 ÷ 7.48 = 8.342. Either value lands inside exam answer tolerance; the plumbing trade standard is 8.33, so use it consistently and never mix the two inside one problem.

Converting Inches to Decimal Feet

Every capacity problem has to be worked in one consistent unit. Because tank and trench dimensions arrive in feet and inches, convert the inches to decimal feet by dividing by 12 before you multiply anything.

  • Inches Decimal foot Inches Decimal foot
  • 1" 0.0833 7" 0.5833
  • 2" 0.1667 8" 0.6667
  • 3" 0.2500 9" 0.7500
  • 4" 0.3333 10" 0.8333
  • 5" 0.4167 11" 0.9167
  • 6" 0.5000 12" 1.0000

A tank 6 feet 9 inches deep is 6 + (9 ÷ 12) = 6.75 feet . A trap arm 3 feet 4 inches long is 3 + (4 ÷ 12) = 3.333 feet .