Study guide

14.2 Plumbing Math II: Offsets, Travel, Grade & Pipe Layout

Maryland Journeyman Plumber Journey Plumber/Gas Fitter

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Maryland Licensing, Code Administration & the Exam

1.1 Maryland Plumbing Regulations & Licensing 1.2 The Journey Plumber/Gas Fitter Exam: Format, References & Open-Book Strategy

2 Chapter 2: Job-Site Safety & OSHA 29 CFR 1926

2.1 OSHA Construction Safety, PPE & Hazard Communication 2.2 Excavation & Trenching Safety (29 CFR 1926 Subpart P) 2.3 Confined Spaces, Ladders, Scaffolds & Hot Work

3 Chapter 3: Materials, Uses & Specifications

3.1 Approved Plumbing Materials, Pipes & Jointing 3.2 Hanger Spacing, Structural Protection & System Testing 3.3 Valves, Fittings, Fitting Selection & Prohibited Connections

4 Chapter 4: Sanitary Drainage & Waste Piping

4.1 Drainage Fixture Units (DFU) & Drain Pipe Sizing 4.2 Building Sewers, Cleanout Clearances & Underground Piping 4.3 Indirect & Special Waste Systems 4.4 Backwater Valves, Sump Pumps & Sewage Ejectors

5 Chapter 5: Venting Systems

5.1 Vent Sizing, Termination & Soil Stacks 5.2 Individual, Branch & Common Vents 5.3 Wet Venting & Circuit Venting 5.4 Air Admittance Valves (AAVs) & Special Venting

6 Chapter 6: Traps, Interceptors & Backwater Valves

6.1 Traps, Trap Seals & Trap Arm Requirements 6.2 Grease, Oil & Special-Waste Interceptors and Separators

7 Chapter 7: Water Supply & Distribution Systems

7.1 Water Supply Sizing & Fixture Unit (WSFU) Method 7.2 Water Heaters & Safety Devices 7.3 Pressure Regulation, Booster Systems & Disinfection 7.4 Water Service Piping, Meters, Valves & System Protection

8 Chapter 8: Backflow Prevention & Cross-Connection Control

8.1 Backflow Prevention & Cross-Connection Control 8.2 Air Gaps, Vacuum Breakers & Their Application Limits 8.3 Double Check & Reduced Pressure Principle (RPZ) Assemblies 8.4 Backflow Assembly Field Testing Procedures & Gauge Use 8.5 Maryland Backflow Program: 32-Hour Course, Certification & Reporting

9 Chapter 9: Fuel Gas Fundamentals, Materials & Pipe Sizing

9.1 Fuel Gas Properties, Heating Values & IFGC Scope 9.2 Fuel Gas Pipe Sizing & Materials 9.3 Approved Gas Piping Materials, CSST & Bonding 9.4 Gas Pipe Sizing Tables: Longest-Length & Branch-Length Methods 9.5 LP-Gas Systems, NFPA 58 & Propane-Specific Rules

10 Chapter 10: Gas Piping Installation, Testing & Purging

10.1 Gas Piping Installation, Testing & Purging 10.2 Gas Piping Support, Protection, Prohibited Locations & Concealed Piping 10.3 Shutoff Valves, Drips, Unions, Sediment Traps & Appliance Connectors 10.4 Gas Meters, Regulators, Pressure Levels & Overpressure Protection 10.5 Gas Leak Detection, Odorization & Emergency Response

11 Chapter 11: Gas Appliance Venting & Combustion Air

11.1 Gas Appliance Venting & Combustion Air 11.2 Appliance Categories I-IV, Vent Materials & Vent Connectors 11.3 Chimney & Vent Sizing Tables (Type B, Masonry & Common Venting) 11.4 Vent Termination, Clearances & Direct-Vent Systems 11.5 Combustion Air: Indoor & Outdoor Methods and Opening Sizing

12 Chapter 12: Gas Appliance Installation & Service

12.1 Gas Water Heaters, Furnaces & Boilers: Installation Rules 12.2 Appliance Clearances to Combustibles, Access & Location Limits 12.3 Gas Appliance Troubleshooting, Combustion Analysis & CO Safety

13 Chapter 13: Plumbing Fixtures, Fittings & Appliances

13.1 Fixture Clearances, Accessibility & Installation 13.2 Water Conservation Standards & Flow Rates 13.3 Commercial & Specialty Fixture Requirements

14 Chapter 14: Plumbing Mathematics

14.1 Plumbing Math I: Areas, Volumes, Capacities & Water Weight 14.2 Plumbing Math II: Offsets, Travel, Grade & Pipe Layout 14.3 Plumbing Math III: Gas Math, Meter Readings, BTU & Pressure Conversions

14.2 Plumbing Math II: Offsets, Travel, Grade & Pipe Layout

Key Takeaways Explain This Topic AI

For a 45-degree offset, travel = offset × 1.414 and run = offset × 1.000; 45 degrees is the only fitting angle where the run equals the offset.

Travel multipliers are 1.155 at 60°, 1.414 at 45°, 2.000 at 30°, 2.613 at 22 1/2° and 5.126 at 11 1/4°, each being 1 ÷ the sine of the angle.

Actual cut length = center-to-center travel − two fitting take-offs + two thread make-ups; a 1-inch 45° malleable elbow takes off 1.12 inches and makes up 11/16 inch.

A rolling offset is solved with a² + b² = c²: a 9-inch rise and a 12-inch roll give a true offset of 15 inches and a 45° travel of 21.21 inches.

Fall equals developed length × slope, so an 86-foot building sewer at 1/8 inch per foot drops 10.75 inches, or 0.896 foot, of invert elevation.

Last updated: July 2026

14.2 Plumbing Math II: Offsets, Travel, Grade & Pipe Layout

Quick Answer: For a 45-degree offset , travel = offset × 1.414 and run = offset × 1.000 . A 16-inch offset therefore needs a center-to-center travel of 16 × 1.414 = 22.62 inches , and the diagonal advances the line exactly 16 inches down the run.

Offset math is the plumber's daily geometry, and every offset is a right triangle in disguise. Two fittings of equal angle move a line sideways around an obstruction: the offset (also called the set ) is one leg, the run (also called the advance ) is the other leg, and the travel — the diagonal piece you actually have to cut — is the hypotenuse.

The Offset Constants

Travel = offset ÷ sine of the fitting angle, and run = offset ÷ tangent of the fitting angle, so every standard fitting carries two fixed multipliers. Memorize the travel column first; the exam asks for travel far more often than for run.

  • Fitting angle Travel = offset × Run = offset × Derivation
  • 60° 1.155 0.577 1 ÷ sin 60° = 1.1547
  • 45° 1.414 1.000 1 ÷ sin 45° = 1.4142
  • 30° 2.000 1.732 1 ÷ sin 30° = 2.0000
  • 22 1/2° 2.613 2.414 1 ÷ sin 22.5° = 2.6131
  • 11 1/4° 5.126 5.027 1 ÷ sin 11.25° = 5.1258

Three facts fall straight out of that table:

At 45 degrees the run always equals the offset. It is the only angle where that is true, which is exactly why the 45 is the workhorse fitting — you can lay out the second fitting with a tape measure and no arithmetic at all.

Shallower angles buy a gentler turn but eat horizontal room. A 22 1/2° offset needs 2.414 times the offset in run; an 11 1/4° offset needs 5.027 times. In a tight ceiling space that constraint picks the fitting for you.

To reverse the calculation, divide. Offset = travel ÷ 1.414.

Pythagorean Solutions and Rolling Offsets

When the fittings are not a standard angle — or when a pipe must shift sideways and up or down in the same move — fall back on a² + b² = c² .

A rolling offset shifts a line horizontally and vertically at once. Solve the true offset first, then treat it as an ordinary offset:

  • true offset = √(vertical offset² + horizontal offset²)
  • Worked Example 1 — Rolling Offset with 45s

A 2-inch line must move 9 inches up and 12 inches over.

  • True offset = √(9² + 12²) = √(81 + 144) = √225 = 15 inches
  • Travel = 15 × 1.414 = 21.21 inches center to center
  • Run (advance along the original line) = 15 × 1.000 = 15 inches

The two 45-degree fittings are then rolled to the angle the true offset makes with vertical, but the pipe length is governed entirely by that 21.21-inch travel.