Study guide
6.1 Traps, Trap Seals & Trap Arm Requirements
Maryland Journeyman Plumber Journey Plumber/Gas Fitter
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Maryland Licensing, Code Administration & the Exam
1.1 Maryland Plumbing Regulations & Licensing 1.2 The Journey Plumber/Gas Fitter Exam: Format, References & Open-Book Strategy
2 Chapter 2: Job-Site Safety & OSHA 29 CFR 1926
2.1 OSHA Construction Safety, PPE & Hazard Communication 2.2 Excavation & Trenching Safety (29 CFR 1926 Subpart P) 2.3 Confined Spaces, Ladders, Scaffolds & Hot Work
3 Chapter 3: Materials, Uses & Specifications
3.1 Approved Plumbing Materials, Pipes & Jointing 3.2 Hanger Spacing, Structural Protection & System Testing 3.3 Valves, Fittings, Fitting Selection & Prohibited Connections
4 Chapter 4: Sanitary Drainage & Waste Piping
4.1 Drainage Fixture Units (DFU) & Drain Pipe Sizing 4.2 Building Sewers, Cleanout Clearances & Underground Piping 4.3 Indirect & Special Waste Systems 4.4 Backwater Valves, Sump Pumps & Sewage Ejectors
5 Chapter 5: Venting Systems
5.1 Vent Sizing, Termination & Soil Stacks 5.2 Individual, Branch & Common Vents 5.3 Wet Venting & Circuit Venting 5.4 Air Admittance Valves (AAVs) & Special Venting
6 Chapter 6: Traps, Interceptors & Backwater Valves
6.1 Traps, Trap Seals & Trap Arm Requirements 6.2 Grease, Oil & Special-Waste Interceptors and Separators
7 Chapter 7: Water Supply & Distribution Systems
7.1 Water Supply Sizing & Fixture Unit (WSFU) Method 7.2 Water Heaters & Safety Devices 7.3 Pressure Regulation, Booster Systems & Disinfection 7.4 Water Service Piping, Meters, Valves & System Protection
8 Chapter 8: Backflow Prevention & Cross-Connection Control
8.1 Backflow Prevention & Cross-Connection Control 8.2 Air Gaps, Vacuum Breakers & Their Application Limits 8.3 Double Check & Reduced Pressure Principle (RPZ) Assemblies 8.4 Backflow Assembly Field Testing Procedures & Gauge Use 8.5 Maryland Backflow Program: 32-Hour Course, Certification & Reporting
9 Chapter 9: Fuel Gas Fundamentals, Materials & Pipe Sizing
9.1 Fuel Gas Properties, Heating Values & IFGC Scope 9.2 Fuel Gas Pipe Sizing & Materials 9.3 Approved Gas Piping Materials, CSST & Bonding 9.4 Gas Pipe Sizing Tables: Longest-Length & Branch-Length Methods 9.5 LP-Gas Systems, NFPA 58 & Propane-Specific Rules
10 Chapter 10: Gas Piping Installation, Testing & Purging
10.1 Gas Piping Installation, Testing & Purging 10.2 Gas Piping Support, Protection, Prohibited Locations & Concealed Piping 10.3 Shutoff Valves, Drips, Unions, Sediment Traps & Appliance Connectors 10.4 Gas Meters, Regulators, Pressure Levels & Overpressure Protection 10.5 Gas Leak Detection, Odorization & Emergency Response
11 Chapter 11: Gas Appliance Venting & Combustion Air
11.1 Gas Appliance Venting & Combustion Air 11.2 Appliance Categories I-IV, Vent Materials & Vent Connectors 11.3 Chimney & Vent Sizing Tables (Type B, Masonry & Common Venting) 11.4 Vent Termination, Clearances & Direct-Vent Systems 11.5 Combustion Air: Indoor & Outdoor Methods and Opening Sizing
12 Chapter 12: Gas Appliance Installation & Service
12.1 Gas Water Heaters, Furnaces & Boilers: Installation Rules 12.2 Appliance Clearances to Combustibles, Access & Location Limits 12.3 Gas Appliance Troubleshooting, Combustion Analysis & CO Safety
13 Chapter 13: Plumbing Fixtures, Fittings & Appliances
13.1 Fixture Clearances, Accessibility & Installation 13.2 Water Conservation Standards & Flow Rates 13.3 Commercial & Specialty Fixture Requirements
14 Chapter 14: Plumbing Mathematics
14.1 Plumbing Math I: Areas, Volumes, Capacities & Water Weight 14.2 Plumbing Math II: Offsets, Travel, Grade & Pipe Layout 14.3 Plumbing Math III: Gas Math, Meter Readings, BTU & Pressure Conversions
6.1 Traps, Trap Seals & Trap Arm Requirements
Key Takeaways Explain This Topic AI
IPC 2018 Section 1002.4 requires every fixture trap to have a liquid seal of not less than 2 inches and not more than 4 inches, deeper only for special designs relating to accessible fixtures.
IPC Table 909.1 caps the developed length from trap weir to vent fitting at 5 feet for a 1-1/4 inch trap, 6 feet for 1-1/2 inch, 8 feet for 2 inch, 12 feet for 3 inch and 16 feet for 4 inch.
IPC Section 909.2 limits the total fall in a fixture drain to one pipe diameter, and the vent connection may not be below the trap weir except for water closets.
IPC Section 1002.3 prohibits bell traps, drum traps, crown-vented traps, S-traps, traps with moving parts and non-integral traps relying on interior partitions; only drum traps used as solids interceptors or on chemical waste systems are excepted.
IPC Section 1002.1 limits the fixture outlet to trap weir drop to 24 inches vertical and 30 inches horizontal centerline to centerline, and Section 1002.5 forbids a trap larger than the drainage pipe it discharges into.
Last updated: July 2026
6.1 Traps, Trap Seals & Trap Arm Requirements
Quick Answer: Under IPC 2018 Section 1002.4 , every fixture trap must hold a liquid seal of not less than 2 inches and not more than 4 inches deep, deeper only for special designs relating to accessible fixtures. The vent protecting that trap must be within the Table 909.1 distances (5 ft for a 1-1/4 in. trap, 6 ft for 1-1/2 in., 8 ft for 2 in., 12 ft for 3 in., 16 ft for 4 in.), and the total fall in the fixture drain may never exceed one pipe diameter (Section 909.2).
"Traps, Interceptors, and Backwater Valves" is worth 4 of the 100 scored questions on the Maryland Journey Plumber/Gas Fitter exam. That is only 4 percent, but the questions are almost all pure lookup-and-apply items drawn from IPC 2018 Chapter 10 and from Section 909 in Chapter 9 — exactly the kind of point you should never lose on an open-book test. Learn where the numbers live and you bank all four.
1. What a Trap Must Do (IPC 1002.2)
A trap is a fitting or device that holds a trap seal — a body of standing water that blocks sewer gas, vermin and odors from entering the building while still passing waste freely. IPC Section 1002.2 imposes three design requirements:
Self-scouring. The trap must be shaped so the discharge velocity sweeps the trap clean on every use. This is why the smooth-bore P-trap survived and the pot-shaped drum trap did not.
No interior partitions. Fixture traps may not use internal baffles to form the seal unless the trap is integral with the fixture (the water closet is the classic example) or is built of an approved corrosion- and degradation-resistant material.
Slip joints only in three places. Slip joints must use an approved elastomeric gasket and may be installed only at the trap inlet , the trap outlet , and within the trap seal . A slip joint buried in a concealed wall downstream of the trap outlet is a violation.
2. Trap Seal Depth (IPC 1002.4)
The seal depth is measured from the trap weir (the crown weir — the top of the outlet bend, where water begins to spill over) down to the trap dip (the bottom of the inlet leg).
Condition Required liquid seal
Standard fixture trap Not less than 2 in. , not more than 4 in.
Special designs relating to accessible fixtures Permitted to be deeper than 4 in.
A seal shallower than 2 inches is destroyed by the smallest pressure fluctuation. A seal deeper than 4 inches on an ordinary fixture is equally wrong: the extra water slows the flush velocity, the trap stops scouring itself, and solids settle out. A deep-seal trap is a legitimate product — it is simply reserved by the code for the accessible-fixture designs it names, and for the special uses (such as evaporation-prone floor drains) the code official approves.