Study guide
7.2 Water Heaters & Safety Devices
Maryland Journeyman Plumber Journey Plumber/Gas Fitter
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Maryland Licensing, Code Administration & the Exam
1.1 Maryland Plumbing Regulations & Licensing 1.2 The Journey Plumber/Gas Fitter Exam: Format, References & Open-Book Strategy
2 Chapter 2: Job-Site Safety & OSHA 29 CFR 1926
2.1 OSHA Construction Safety, PPE & Hazard Communication 2.2 Excavation & Trenching Safety (29 CFR 1926 Subpart P) 2.3 Confined Spaces, Ladders, Scaffolds & Hot Work
3 Chapter 3: Materials, Uses & Specifications
3.1 Approved Plumbing Materials, Pipes & Jointing 3.2 Hanger Spacing, Structural Protection & System Testing 3.3 Valves, Fittings, Fitting Selection & Prohibited Connections
4 Chapter 4: Sanitary Drainage & Waste Piping
4.1 Drainage Fixture Units (DFU) & Drain Pipe Sizing 4.2 Building Sewers, Cleanout Clearances & Underground Piping 4.3 Indirect & Special Waste Systems 4.4 Backwater Valves, Sump Pumps & Sewage Ejectors
5 Chapter 5: Venting Systems
5.1 Vent Sizing, Termination & Soil Stacks 5.2 Individual, Branch & Common Vents 5.3 Wet Venting & Circuit Venting 5.4 Air Admittance Valves (AAVs) & Special Venting
6 Chapter 6: Traps, Interceptors & Backwater Valves
6.1 Traps, Trap Seals & Trap Arm Requirements 6.2 Grease, Oil & Special-Waste Interceptors and Separators
7 Chapter 7: Water Supply & Distribution Systems
7.1 Water Supply Sizing & Fixture Unit (WSFU) Method 7.2 Water Heaters & Safety Devices 7.3 Pressure Regulation, Booster Systems & Disinfection 7.4 Water Service Piping, Meters, Valves & System Protection
8 Chapter 8: Backflow Prevention & Cross-Connection Control
8.1 Backflow Prevention & Cross-Connection Control 8.2 Air Gaps, Vacuum Breakers & Their Application Limits 8.3 Double Check & Reduced Pressure Principle (RPZ) Assemblies 8.4 Backflow Assembly Field Testing Procedures & Gauge Use 8.5 Maryland Backflow Program: 32-Hour Course, Certification & Reporting
9 Chapter 9: Fuel Gas Fundamentals, Materials & Pipe Sizing
9.1 Fuel Gas Properties, Heating Values & IFGC Scope 9.2 Fuel Gas Pipe Sizing & Materials 9.3 Approved Gas Piping Materials, CSST & Bonding 9.4 Gas Pipe Sizing Tables: Longest-Length & Branch-Length Methods 9.5 LP-Gas Systems, NFPA 58 & Propane-Specific Rules
10 Chapter 10: Gas Piping Installation, Testing & Purging
10.1 Gas Piping Installation, Testing & Purging 10.2 Gas Piping Support, Protection, Prohibited Locations & Concealed Piping 10.3 Shutoff Valves, Drips, Unions, Sediment Traps & Appliance Connectors 10.4 Gas Meters, Regulators, Pressure Levels & Overpressure Protection 10.5 Gas Leak Detection, Odorization & Emergency Response
11 Chapter 11: Gas Appliance Venting & Combustion Air
11.1 Gas Appliance Venting & Combustion Air 11.2 Appliance Categories I-IV, Vent Materials & Vent Connectors 11.3 Chimney & Vent Sizing Tables (Type B, Masonry & Common Venting) 11.4 Vent Termination, Clearances & Direct-Vent Systems 11.5 Combustion Air: Indoor & Outdoor Methods and Opening Sizing
12 Chapter 12: Gas Appliance Installation & Service
12.1 Gas Water Heaters, Furnaces & Boilers: Installation Rules 12.2 Appliance Clearances to Combustibles, Access & Location Limits 12.3 Gas Appliance Troubleshooting, Combustion Analysis & CO Safety
13 Chapter 13: Plumbing Fixtures, Fittings & Appliances
13.1 Fixture Clearances, Accessibility & Installation 13.2 Water Conservation Standards & Flow Rates 13.3 Commercial & Specialty Fixture Requirements
14 Chapter 14: Plumbing Mathematics
14.1 Plumbing Math I: Areas, Volumes, Capacities & Water Weight 14.2 Plumbing Math II: Offsets, Travel, Grade & Pipe Layout 14.3 Plumbing Math III: Gas Math, Meter Readings, BTU & Pressure Conversions
7.2 Water Heaters & Safety Devices
Key Takeaways Explain This Topic AI
Temperature & Pressure (T&P) relief valves must be set to open at a maximum pressure of 150 psi and a maximum temperature of 210°F (99°C), with a BTUH rating matching or exceeding heater input.
T&P discharge piping must be full size (min 3/4 inch), constructed of approved rigid materials, terminate indirectly 2 to 6 inches above the floor/drain with no threads, no valves, and no low points.
Thermal expansion tanks are mandatory on closed potable systems (created by PRVs or backflow preventers) and must be air pre-charged to equal incoming static cold water pressure prior to installation.
Anti-scald protection standards require ASSE 1016 shower valves to limit delivery to 120°F (49°C) max, ASSE 1070 public lavatory valves to 110°F max, and ASSE 1017 master mixing valves at water heaters.
Water heaters generating sparks in residential garages must have ignition sources elevated at least 18 inches above the floor unless listed as Flammable Vapor Ignition Resistant (FVIR).
Last updated: July 2026
7.2 Water Heaters & Safety Devices
Water heaters are pressurized thermal energy vessels present in virtually every plumbing system. Governed by IPC Chapter 5 (Water Heaters) and IPC Section 607 (Hot Water Supply System) , water heater installations require rigorous safety engineering. Because water expands when heated and can reach temperatures capable of causing instant third-degree thermal burns or violent explosive tank rupture, Journeyman Plumbers must strictly execute rules governing Temperature and Pressure (T&P) relief valves, thermal expansion control, anti-scald mixing valves, and installation clearances.
1. Temperature & Pressure (T&P) Relief Valves
A Temperature & Pressure (T&P) Relief Valve (conforming to ANSI Z21.22 / CSA 4.4) is the primary emergency safety device protecting against water heater catastrophic explosion. If a water heater thermostat fails in the closed position, heating elements or gas burners will continuously boil the trapped water. Water superheated above 212 ∘ F 212^\circ\text{F} 21 2 ∘ F inside a sealed tank under pressure remains liquid; however, if the tank ruptures, superheated water instantly flashes into steam, expanding 1 , 600 times 1,600 \text{ times} 1 , 600 times its liquid volume, destroying entire buildings.
Mandatory Operating Ratings (IPC 504.4)
Maximum Pressure Setting: 150 psi (1,034 kPa) (or the rated working pressure of the tank, whichever is lower).
Maximum Temperature Setting: 210°F (99°C) .
BTUH Discharge Capacity: The T&P valve's ASME temperature steam relief rating must equal or exceed the total heat input rating (BTUH or kW) of the water heater.
Sensing Element Location: The temperature sensing probe must extend into the top 6 inches (152 mm) of the tank, where the hottest water naturally accumulates due to thermal stratification.
2. IPC 504.6 Discharge Pipe Strict Installation Rules
The discharge pipe attached to a T&P relief valve outlet is subject to 14 non-negotiable IPC installation rules . Violating any of these rules can turn a safety device into a deadly hazard.
Full Size: Pipe diameter must be at least full nominal size of the valve outlet (never reduced below 3/4 inch).
Approved Materials: Must be rigid pipe approved for hot water distribution (Copper, CPVC, Galvanized Steel, PE-RT, or stainless steel). PEX and PE-RT are permitted for relief discharge piping, but the piping must be one nominal size larger than the relief valve outlet and the outlet end of the tubing must be fastened in place (IPC 504.6, items 13 and 14).
No Threaded Outlets: The terminal end of the discharge pipe must NOT be threaded (prevents building occupants from screwing on a cap or plug to stop nuisance drips).
No Valves or Tees: Zero shutoff valves, check valves, or tee fittings are permitted anywhere in the discharge line.
Continuous Gravity Slope: Must pitch downward continuously toward the point of discharge (no low points, sags, or traps that trap water and create static head pressure).
Air Gap Termination: Must terminate indirectly into an approved floor drain, waste receptor, or outdoors through an air gap.
Termination Height: Must terminate not more than 6 inches above , and not less than two times the discharge pipe diameter above , the floor or flood level rim of the waste receptor (IPC 504.6, item 10).
No Concealed Termination: The discharge point must be readily visible to building occupants so leaks are immediately noticed.
No Freezing: Must not discharge where ice formation could block the pipe end outdoors.
3. Thermal Expansion Control in Closed Systems
When water is heated from 40 ∘ F 40^\circ\text{F} 4 0 ∘ F to 140 ∘ F 140^\circ\text{F} 14 0 ∘ F , it expands in volume by approximately 1.7% to 2.0% . In an open plumbing system, expanding water simply flows backwards through the service line into the municipal main.
However, modern plumbing codes mandate backflow preventers, check valves, or Pressure Reducing Valves (PRV) at the water service entry. These devices act as one-way check valves, creating a Closed System . When water heats inside a closed system, expanding water has nowhere to go. System pressure rapidly spikes from 50 psi to over 150 psi every time the water heater fires, popping the T&P relief valve and destroying valve seals.
Thermal Expansion Tank Installation (IPC 607.3)
Under IPC 607.3, an approved thermal expansion tank (or equivalent pressure relief device) must be installed on any closed potable water system.
Location: Installed on the cold water supply line between the water heater inlet and the backflow preventer/PRV.
Internal Design: Features a heavy-duty butyl rubber diaphragm separating a pre-charged air chamber from the potable water chamber.
Air Pre-Charge Rule: The expansion tank air valve (Schrader valve) must be pre-charged with air to equal the static cold water pressure of the building prior to installation! (e.g. If main static pressure is 60 psi, air pre-charge must be adjusted to 60 psi). Expansion Volume Required ( V e ) = V t a n k × e \text{Expansion Volume Required } (V_e) = V_{tank} \times e Expansion Volume Required ( V e ) = V t ank × e
Where V t a n k V_{tank} V t ank = total water heater volume, and e e e = thermal expansion coefficient (~0.0172 for 40 ∘ F → 140 ∘ F 40^\circ\text{F} \rightarrow 140^\circ\text{F} 4 0 ∘ F → 14 0 ∘ F ).
4. Anti-Scald Protection & Temperature Limiting Standards
Hot water delivered to plumbing fixtures presents severe thermal burn hazards, particularly to children, the elderly, and mobility-impaired individuals.
Water Temperature Burn Severity Thresholds
160°F (71°C): Instantaneous third-degree burn (less than 0.5 seconds).
140°F (60°C): Third-degree burn in 5 seconds .
130°F (54°C): Third-degree burn in 30 seconds .
120°F (49°C): Third-degree burn takes over 5 minutes (safe domestic maximum).
IPC & ASSE Temperature Control Standards
Safety Standard Valve Type & Application Max Allowable Temp Application Details
ASSE 1017 Master Thermostatic Mixing Valve 120°F (recommended) Installed at water heater outlet; allows storage at 140°F+ (kills Legionella ) while tempering delivery to 120°F.
ASSE 1016 / ASME A112.18.1 Automatic Compensating Shower Valve 120°F (49°C) Mandated for all individual showers and tub/shower combinations. Protects against thermal shock & scalding.
ASSE 1070 Water Temperature Limiting Device 110°F (43°C) Mandated for public handwashing lavatories, bidet fixtures, and gang sinks.
Pathogen Control vs. Anti-Scald: Storing water below 140°F in water heater tanks promotes colonization of Legionella pneumophila bacteria (the cause of Legionnaires' disease). The ultimate plumbing standard is to store water at 140°F inside the tank to kill bacteria, and install an ASSE 1017 master mixing valve on the outlet set to 120°F for safe distribution.
- 5. Water Heater Pans & Garage Ignition Elevation
- Drain Pans (IPC 504.7)
Where water heaters are installed in attics, ceiling spaces, floor/ceiling assemblies, or locations where tank leakage would cause structural damage to floors or finished ceilings below:
Must sit inside a corrosion-resistant pan (min. 24-gauge galvanized steel or approved plastic).
Pan depth must be at least 1.5 inches (38 mm) .
Pan must have a minimum 3/4-inch nominal drain line discharging indirectly to an approved floor drain or outdoors between 6 inches and 24 inches above grade.
Garage Elevation Rule (IPC 502.1 / Fuel Gas Code)
Water heaters generating a spark, flame, or glow installed in residential garages must be installed so that burner ignition sources are elevated at least 18 inches (457 mm) above the garage floor .
Reason: Gasoline vapors are heavier than air and pool along the garage floor. Elevating ignition sources 18 inches prevents flammable vapor ignition. (Note: Water heaters listed as Flammable Vapor Ignition Resistant [FVIR] are exempt from the 18-inch elevation rule unless mandated by local Maryland utility codes) .