Study guide
7.1 Water Supply Sizing & Fixture Unit (WSFU) Method
Maryland Journeyman Plumber Journey Plumber/Gas Fitter
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Maryland Licensing, Code Administration & the Exam
1.1 Maryland Plumbing Regulations & Licensing 1.2 The Journey Plumber/Gas Fitter Exam: Format, References & Open-Book Strategy
2 Chapter 2: Job-Site Safety & OSHA 29 CFR 1926
2.1 OSHA Construction Safety, PPE & Hazard Communication 2.2 Excavation & Trenching Safety (29 CFR 1926 Subpart P) 2.3 Confined Spaces, Ladders, Scaffolds & Hot Work
3 Chapter 3: Materials, Uses & Specifications
3.1 Approved Plumbing Materials, Pipes & Jointing 3.2 Hanger Spacing, Structural Protection & System Testing 3.3 Valves, Fittings, Fitting Selection & Prohibited Connections
4 Chapter 4: Sanitary Drainage & Waste Piping
4.1 Drainage Fixture Units (DFU) & Drain Pipe Sizing 4.2 Building Sewers, Cleanout Clearances & Underground Piping 4.3 Indirect & Special Waste Systems 4.4 Backwater Valves, Sump Pumps & Sewage Ejectors
5 Chapter 5: Venting Systems
5.1 Vent Sizing, Termination & Soil Stacks 5.2 Individual, Branch & Common Vents 5.3 Wet Venting & Circuit Venting 5.4 Air Admittance Valves (AAVs) & Special Venting
6 Chapter 6: Traps, Interceptors & Backwater Valves
6.1 Traps, Trap Seals & Trap Arm Requirements 6.2 Grease, Oil & Special-Waste Interceptors and Separators
7 Chapter 7: Water Supply & Distribution Systems
7.1 Water Supply Sizing & Fixture Unit (WSFU) Method 7.2 Water Heaters & Safety Devices 7.3 Pressure Regulation, Booster Systems & Disinfection 7.4 Water Service Piping, Meters, Valves & System Protection
8 Chapter 8: Backflow Prevention & Cross-Connection Control
8.1 Backflow Prevention & Cross-Connection Control 8.2 Air Gaps, Vacuum Breakers & Their Application Limits 8.3 Double Check & Reduced Pressure Principle (RPZ) Assemblies 8.4 Backflow Assembly Field Testing Procedures & Gauge Use 8.5 Maryland Backflow Program: 32-Hour Course, Certification & Reporting
9 Chapter 9: Fuel Gas Fundamentals, Materials & Pipe Sizing
9.1 Fuel Gas Properties, Heating Values & IFGC Scope 9.2 Fuel Gas Pipe Sizing & Materials 9.3 Approved Gas Piping Materials, CSST & Bonding 9.4 Gas Pipe Sizing Tables: Longest-Length & Branch-Length Methods 9.5 LP-Gas Systems, NFPA 58 & Propane-Specific Rules
10 Chapter 10: Gas Piping Installation, Testing & Purging
10.1 Gas Piping Installation, Testing & Purging 10.2 Gas Piping Support, Protection, Prohibited Locations & Concealed Piping 10.3 Shutoff Valves, Drips, Unions, Sediment Traps & Appliance Connectors 10.4 Gas Meters, Regulators, Pressure Levels & Overpressure Protection 10.5 Gas Leak Detection, Odorization & Emergency Response
11 Chapter 11: Gas Appliance Venting & Combustion Air
11.1 Gas Appliance Venting & Combustion Air 11.2 Appliance Categories I-IV, Vent Materials & Vent Connectors 11.3 Chimney & Vent Sizing Tables (Type B, Masonry & Common Venting) 11.4 Vent Termination, Clearances & Direct-Vent Systems 11.5 Combustion Air: Indoor & Outdoor Methods and Opening Sizing
12 Chapter 12: Gas Appliance Installation & Service
12.1 Gas Water Heaters, Furnaces & Boilers: Installation Rules 12.2 Appliance Clearances to Combustibles, Access & Location Limits 12.3 Gas Appliance Troubleshooting, Combustion Analysis & CO Safety
13 Chapter 13: Plumbing Fixtures, Fittings & Appliances
13.1 Fixture Clearances, Accessibility & Installation 13.2 Water Conservation Standards & Flow Rates 13.3 Commercial & Specialty Fixture Requirements
14 Chapter 14: Plumbing Mathematics
14.1 Plumbing Math I: Areas, Volumes, Capacities & Water Weight 14.2 Plumbing Math II: Offsets, Travel, Grade & Pipe Layout 14.3 Plumbing Math III: Gas Math, Meter Readings, BTU & Pressure Conversions
7.1 Water Supply Sizing & Fixture Unit (WSFU) Method
Key Takeaways Explain This Topic AI
IPC Table E103.3(2) establishes Water Supply Fixture Unit (WSFU) values: a private flush-tank water closet is 2.2 WSFU, a public flush-tank water closet 5.0, a private flushometer-valve water closet 6.0, and a public flushometer-valve water closet 10.0. Table 604.3 assigns no WSFU values — it lists required flow rates and flow pressures.
Peak demand conversion uses Table E103.3(3): 100 WSFU on a predominantly flush-tank system is about 43.5 GPM, while 100 WSFU on a predominantly flushometer-valve system is about 67.5 GPM.
Design velocity should be held to about 8 feet per second for cold water and 5 feet per second for hot water under copper-industry (CDA) guidance and the design-velocity provisions of IPC Appendix E; IPC 604.4 is 'Maximum flow and water consumption' and sets no velocity cap.
Minimum flow pressures in IPC Table 604.3 run from 8 psi for lavatories, sinks and hose bibbs, to 20 psi for a tank-type water closet and thermostatic shower valve, 25 psi for a urinal flushometer valve, and 35 psi for a siphonic water closet flushometer valve (45 psi blowout); the minimum water service pipe size is 3/4 inch.
The pressure drop method calculates permissible friction loss by subtracting elevation head loss (0.433 psi per foot), meter pressure loss, and required residual pressure from available main static pressure.
Last updated: July 2026
7.1 Water Supply Sizing & Fixture Unit (WSFU) Method
Designing a safe, reliable, and efficient potable water supply distribution system is a core responsibility of a Journeyman Plumber. In Maryland, water supply design is governed by the International Plumbing Code (IPC) Chapter 6 and Appendix E, alongside local utility regulations (such as WSSC Water in Prince George's and Montgomery Counties, or Baltimore City DPW). A properly sized water supply system must deliver adequate flow rate (GPM) and residual pressure (psi) to every plumbing fixture under peak demand conditions, while maintaining water velocity below maximum safety thresholds to prevent pipe erosion, hydraulic noise, and destructive water hammer.
1. Fundamentals of the Water Supply Fixture Unit (WSFU) System
Directly sizing water piping based on the total potential flow of all installed fixtures running simultaneously would result in absurdly oversized, expensive, and stagnant piping networks. Plumbing fixtures operate intermittently. To account for the statistical probability that only a fraction of fixtures will operate concurrently, empirical research conducted by Dr. Roy B. Hunter of the National Bureau of Standards established the Water Supply Fixture Unit (WSFU) system.
A Water Supply Fixture Unit (WSFU) is a dimensionless design index that represents the relative load drawn by a specific plumbing fixture onto the water supply system. WSFU values account for:
Flow rate demand of the fixture (GPM).
Average duration of an operational cycle.
Frequency of use (interval between cycles).
Crucial Exam Distinction: Never confuse WSFU (Water Supply Fixture Units) with DFU (Drainage Fixture Units). DFU values (IPC Chapter 7) dictate drain and vent pipe sizing based on wastewater discharge rates (1 DFU = 7.5 GPM discharge rate). WSFU values (IPC Chapter 6) dictate supply pipe sizing based on potable water draw. They originate from completely separate tables and cannot be interchanged!
2. Flush Tank vs. Flushometer Valve Fixture Load Sizing
Plumbing fixtures fall into two primary hydraulic operational categories: flush tanks (gravity tank water closets, residential sinks) and flushometer valves (direct pressure flush valves for commercial water closets and urinals).
Flush tanks fill slowly through a small ballcock or fill valve over 45 to 60 seconds at a low flow rate (1.5 to 3.0 GPM). In contrast, flushometer valves open wide and deliver a powerful, instantaneous burst of water directly from the supply main (25 to 40 GPM) over a brief 4-to-7 second flushing cycle. Consequently, systems supplying flushometer valves experience dramatically higher peak flow demands for an equivalent number of fixture units.
IPC Table E103.3(2) WSFU Values & Table 604.3 Flow/Pressure Requirements
Plumbing Fixture Type Load (WSFU) - Cold Load (WSFU) - Hot Load (WSFU) - Total Min. Residual Pressure (psi) Min. Flow Rate (GPM)
- Water Closet (Flush Tank - Private) 2.2 0.0 2.2 20 3.0
- Water Closet (Flush Tank - Public) 5.0 0.0 5.0 20 3.0
- Water Closet (Flushometer Valve - Public) 10.0 0.0 10.0 35 25.0
- Urinal (3/4-inch Flushometer Valve, Public) 5.0 0.0 5.0 25 12.0
- Lavatory (Private) 0.5 0.5 0.7 8 0.8
- Lavatory (Public) 1.5 1.5 2.0 8 0.4
- Bathtub (Private, Faucet) 1.0 1.0 1.4 20 4.0
- Kitchen Sink (Private) 1.0 1.0 1.4 8 1.75
- Hose Bibb (First outlet / Residential) 2.5 0.0 2.5 8 5.0
- Hose Bibb (Each additional outlet) 1.0 0.0 1.0 8 5.0
- 3. Converting WSFU to Peak Gallons Per Minute (GPM)
Once the total WSFU load for a building or pipe segment is calculated, it must be converted into peak water demand in Gallons Per Minute (GPM) using Hunter's Curve (IPC Appendix E, Table E103.3(3)). Because flushometer valves impose massive instantaneous surges, two separate curves exist: Curve 1 (Predominantly Flushometer Valves) and Curve 2 (Predominantly Flush Tanks) .
Peak Demand (GPM) Comparison: Flush Tank vs. Flushometer Systems
- Total WSFU Load Peak Demand: Flush Tank System (GPM) Peak Demand: Flushometer System (GPM)
- 10 14.6 GPM 27.0 GPM
- 20 19.6 GPM 35.0 GPM
- 50 29.1 GPM 50.0 GPM
- 100 43.5 GPM 67.5 GPM
- 200 65.0 GPM 90.0 GPM
- 500 124.0 GPM 143.0 GPM
Exam Trap (Continuous Loads): Non-discretionary continuous loads—such as lawn irrigation systems, commercial ice machines, air conditioning cooling towers, and hose bibbs operating continuously—are NOT included in the WSFU total! You must convert the intermittent fixture load to GPM via Hunter's Curve first, and then add the continuous GPM load directly to the peak GPM demand.
Example Calculation: A building has a 100 WSFU flush tank load plus a 15 GPM continuous lawn sprinkler load.
Total Peak Demand = 43.5 GPM (from Hunter's Curve for 100 WSFU) + 15.0 GPM (continuous) = 58.5 GPM .
4. The Pressure Drop Sizing Method (Step-by-Step)
IPC Appendix E details the standard engineering protocol for sizing water supply distribution networks: the Simplified Pressure Drop Method . This method ensures that the hydraulic friction loss inside pipes does not reduce water pressure below the minimum residual pressure needed at the most hydraulically remote fixture outlet.
Step 1: Determine System Pressure & Elevation Head Loss
Static water pressure at the municipal main or well pressure tank serves as the initial energy baseline ( P s t a t i c P_{static} P s t a t i c ).
Calculate elevation head loss ( P e l e v P_{elev} P e l e v ) caused by gravity as water rises to upper floor levels: Elevation Head Loss ( P e l e v ) = Elevation Gain (feet) × 0.433 psi/ft \text{Elevation Head Loss } (P_{elev}) = \text{Elevation Gain (feet)} \times 0.433 \text{ psi/ft} Elevation Head Loss ( P e l e v ) = Elevation Gain (feet) × 0.433 psi/ft
(Note: If the fixture is located below the main, elevation creates a pressure gain of 0.433 psi per foot of fall) .
Step 2: Subtract Equipment Pressure Drops
Subtract pressure drops caused by water meters, backflow preventers, pressure reducing valves (PRV), water softeners, and filters ( P e q u i p m e n t P_{equipment} P e q u i p m e n t ). Water meters typically consume 5 to 15 psi depending on flow rate; RPZ backflow preventers introduce a fixed 10 to 12 psi drop across their relief mechanism.
Step 3: Determine Minimum Required Residual Pressure
Identify the highest residual pressure requirement ( P r e s i d u a l P_{residual} P res i d u a l ) among all fixtures on the line (IPC Table 604.3). Per Table 604.3, lavatories, sinks and hose bibbs require 8 psi ; a tank-type water closet 20 psi ; a urinal flushometer valve 25 psi ; a siphonic water closet flushometer valve 35 psi (blowout, 45 psi); and thermostatic shower and tub valves 20 psi .
Step 4: Calculate Available Pressure Loss for Pipe Friction Permissible Friction Loss ( P l o s s ) = P s t a t i c − P e l e v − P e q u i p m e n t − P r e s i d u a l \text{Permissible Friction Loss } (P_{loss}) = P_{static} - P_{elev} - P_{equipment} - P_{residual} Permissible Friction Loss ( P l oss ) = P s t a t i c − P e l e v − P e q u i p m e n t − P res i d u a l
Step 5: Determine Developed Pipe Length & Equivalent Fitting Length
Measure the actual physical pipe distance from the water main to the furthest fixture. To account for internal turbulence caused by elbows, tees, and valves, add 50% to the actual length to establish the Total Developed Length ( L d e v L_{dev} L d e v ): L d e v = Actual Length (feet) × 1.50 L_{dev} = \text{Actual Length (feet)} \times 1.50 L d e v = Actual Length (feet) × 1.50
Step 6: Calculate Allowable Friction Loss per 100 Feet Allowable Friction Loss per 100 ft = ( P l o s s L d e v ) × 100 \text{Allowable Friction Loss per 100 ft} = \left( \frac{P_{loss}}{L_{dev}} \right) \times 100 Allowable Friction Loss per 100 ft = ( L d e v P l oss ) × 100
Use friction head loss charts (Hazen-Williams formula for Type L copper, CPVC, or PEX) to select the smallest pipe diameter that keeps friction loss within this allowable limit at the required peak GPM.
5. Maximum Allowable Water Velocity Limits
Pipe sizing is not dictated solely by pressure drop; it is strictly bounded by maximum permissible fluid velocity. Under copper industry standards (CDA guidelines) and the design-velocity provisions of IPC Appendix E, water velocity inside supply piping should not exceed the following. Note that IPC 604.4 is "Maximum flow and water consumption" (the gpm/gpf fixture limits) and sets no velocity cap :
Cold Water Piping Maximum Velocity: 8.0 feet per second (fps) .
Hot Water Piping Maximum Velocity: 5.0 feet per second (fps) .
Why Are Velocity Limits Strictly Enforced?
Erosion-Corrosion (Copper Pitting): When water flows through copper tubing above 8 fps (or above 5 fps in hot water lines over 140°F), turbulent shear stress strips the protective cuprous oxide film from the internal pipe wall. This causes rapid mechanical erosion, wall thinning, pinhole leaks, and catastrophic line failure.
Water Hammer: High velocity amplifies kinetic energy ( E k = 1 2 m v 2 E_k = \frac{1}{2} m v^2 E k = 2 1 m v 2 ). When quick-closing solenoid valves (washing machines, dishwashers, flushometers) snap shut, high-velocity water columns create violent pressure shockwaves (water hammer) exceeding 300 psi, rupturing pipe joints.
Noise: Excessive velocity causes high-frequency whistle and hum inside building walls. Velocity Formula: V = 0.408 × Q d 2 \text{Velocity Formula: } V = \frac{0.408 \times Q}{d^2} Velocity Formula: V = d 2 0.408 × Q
Where V V V = velocity (fps), Q Q Q = flow rate (GPM), and d d d = internal pipe diameter (inches).
6. Minimum Water Service Pipe Sizing
Under IPC Section 603.1 , no water service pipe supplying any building shall be less than 3/4 inch (19.1 mm) nominal diameter. Even if a small single-bathroom dwelling calculates to a load requiring only 1/2-inch pipe for flow, the underground water service from the street main or well casing to the main building shutoff valve must be at least 3/4 inch to provide structural strength and resist ground shear stress.
7. Exam Traps & Journeyman Summary Checklist
Trap 1: Sizing a commercial flushometer line using flush tank WSFU values. Always verify whether the water closet uses a flushometer valve ( 10 WSFU public, 6 WSFU private ) or a flush tank ( 5 WSFU public, 2.2 WSFU private ).
Trap 2: Forgetting the 5.0 fps hot water velocity limit. Hot water recirculating loops must be sized generously to maintain velocity below 5 fps (ideally 3 to 4 fps).
Trap 3: Omitting meter loss or RPZ loss in pressure drop calculations. An RPZ backflow preventer loses approx 12 psi instantly; neglecting it will cause top-floor showers to lose pressure whenever lower-floor fixtures open.
Trap 4: Confusing elevation head loss and gain. Elevation gain (going up) subtracts 0.433 psi per foot. Elevation drop (going down to a basement) adds 0.433 psi per foot.